High‐speed surface temperature measurements on plasma facing materials for fusion applications

1996 ◽  
Vol 67 (1) ◽  
pp. 178-184 ◽  
Author(s):  
Masanori Araki ◽  
Masanobu Kobayashi
Keyword(s):  
Surface Temperature ◽  
High Speed ◽  
Temperature Measurements ◽  
Fusion Applications ◽  
Plasma Facing Materials

scholarly journals Effect of Surface Oxidation on the Onset of Nucleate Boiling in a Materials Test Reactor Coolant Channel

2016 ◽  
Vol 2 (2) ◽  
Author(s):  
Eric C. Forrest ◽  
Sarah M. Don ◽  
Lin-Wen Hu ◽  
Jacopo Buongiorno ◽  
Thomas J. McKrell
Keyword(s):  
Heat Flux ◽  
Surface Temperature ◽  
High Speed ◽  
Surface Oxidation ◽  
Nucleate Boiling ◽  
Temperature Measurements ◽  
Native Oxide ◽  
Oxide Surface ◽  
Surface Conditions ◽  
Test Reactor

The onset of nucleate boiling (ONB) serves as the thermal-hydraulic operating limit for many research and test reactors. However, boiling incipience under forced convection has not been well-characterized in narrow channel geometries or for oxidized surface conditions. This study presents experimental data for the ONB in vertical upflow of deionized (DI) water in a simulated materials test reactor (MTR) coolant channel. The channel gap thickness and aspect ratio were 1.96 mm and 29∶1, respectively. Boiling surface conditions were carefully controlled and characterized, with both heavily oxidized and native oxide surfaces tested. Measurements were performed for mass fluxes ranging from 750 to 3000  kg/m2 s and for subcoolings ranging from 10 to 45°C. ONB was identified using a combination of high-speed visual observation, surface temperature measurements, and channel pressure drop measurements. Surface temperature measurements were found to be most reliable in identifying the ONB. For the nominal (native oxide) surface, results indicate that the correlation of Bergles and Rohsenow, when paired with the appropriate single-phase heat transfer correlation, adequately predicts the ONB heat flux. Incipience on the oxidized surface occurred at a higher heat flux and superheat than on the plain surface.

scholarly journals Operating temperatures of oil-lubricated medium-speed gears: Numerical models and experimental results

2003 ◽  
Vol 217 (2) ◽  
pp. 87-106 ◽  
Author(s):  
H Long ◽  
A A Lord ◽  
D T Gethin ◽  
B J Roylance
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Temperature ◽  
Rotational Speed ◽  
High Speed ◽  
Applied Load ◽  
Frictional Heat ◽  
Transfer Coefficients ◽  
Gear Teeth ◽  
Heat Transfer Coefficients

This paper investigates the effects of gear geometry, rotational speed and applied load, as well as lubrication conditions on surface temperature of high-speed gear teeth. The analytical approach and procedure for estimating frictional heat flux and heat transfer coefficients of gear teeth in high-speed operational conditions was developed and accounts for the effect of oil mist as a cooling medium. Numerical simulations of tooth temperature based on finite element analysis were established to investigate temperature distributions and variations over a range of applied load and rotational speed, which compared well with experimental measurements. A sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperatures was conducted and the major parameters influencing surface temperature were evaluated.

scholarly journals Wall Temperature Measurements in Gas Turbine Combustors With Thermographic Phosphors

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Patrick Nau ◽  
Zhiyao Yin ◽  
Oliver Lammel ◽  
Wolfgang Meier
Keyword(s):  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Bluff Body ◽  
Temperature Measurements ◽  
Transient Temperature ◽  
High Time Resolution ◽  
Ceramic Surface ◽  
Precessing Vortex Core

Phosphor thermometry has been developed for wall temperature measurements in gas turbines and gas turbine model combustors. An array of phosphors has been examined in detail for spatially and temporally resolved surface temperature measurements. Two examples are provided, one at high pressure (8 bar) and high temperature and one at atmospheric pressure with high time resolution. To study the feasibility of this technique for full-scale gas turbine applications, a high momentum confined jet combustor at 8 bar was used. Successful measurements up to 1700 K on a ceramic surface are shown with good accuracy. In the same combustor, temperatures on the combustor quartz walls were measured, which can be used as boundary conditions for numerical simulations. An atmospheric swirl-stabilized flame was used to study transient temperature changes on the bluff body. For this purpose, a high-speed setup (1 kHz) was used to measure the wall temperatures at an operating condition where the flame switches between being attached (M-flame) and being lifted (V-flame) (bistable). The influence of a precessing vortex core (PVC) present during M-flame periods is identified on the bluff body tip, but not at positions further inside the nozzle.

Sign in / Sign up

Export Citation Format

Share Document