Vertical photon beam position measurement at bending magnets using lateral diodes

1995 ◽  
Vol 66 (2) ◽  
pp. 1889-1891 ◽  
Author(s):  
K. Holldack ◽  
W. B. Peatman ◽  
Th. Schroeter
Keyword(s):  
Photon Beam ◽  
Position Measurement ◽  
Beam Position ◽  
Lateral Diodes

scholarly journals A phase-space beam position monitor for synchrotron radiation

2015 ◽  
Vol 22 (4) ◽  
pp. 946-955 ◽  
Author(s):  
Nazanin Samadi ◽  
Bassey Bassey ◽  
Mercedes Martinson ◽  
George Belev ◽  
Les Dallin ◽  
...  
Keyword(s):  
Phase Space ◽  
Synchrotron Radiation ◽  
Incident Angle ◽  
Operating Conditions ◽  
Photon Beam ◽  
Profile Measurement ◽  
Beam Position Monitor ◽  
Position Measurement ◽  
Beam Position ◽  
X Ray

The stability of the photon beam position on synchrotron beamlines is critical for most if not all synchrotron radiation experiments. The position of the beam at the experiment or optical element location is set by the position and angle of the electron beam source as it traverses the magnetic field of the bend-magnet or insertion device. Thus an ideal photon beam monitor would be able to simultaneously measure the photon beam's position and angle, and thus infer the electron beam's position in phase space. X-ray diffraction is commonly used to prepare monochromatic beams on X-ray beamlines usually in the form of a double-crystal monochromator. Diffraction couples the photon wavelength or energy to the incident angle on the lattice planes within the crystal. The beam from such a monochromator will contain a spread of energies due to the vertical divergence of the photon beam from the source. This range of energies can easily cover the absorption edge of a filter element such as iodine at 33.17 keV. A vertical profile measurement of the photon beam footprint with and without the filter can be used to determine the vertical centroid position and angle of the photon beam. In the measurements described here an imaging detector is used to measure these vertical profiles with an iodine filter that horizontally covers part of the monochromatic beam. The goal was to investigate the use of a combined monochromator, filter and detector as a phase-space beam position monitor. The system was tested for sensitivity to position and angle under a number of synchrotron operating conditions, such as normal operations and special operating modes where the photon beam is intentionally altered in position and angle at the source point. The results are comparable with other methods of beam position measurement and indicate that such a system is feasible in situations where part of the synchrotron beam can be used for the phase-space measurement.

Photon beam position measurement system based on four-quadrant detector

2010 ◽  
Vol 22 (12) ◽  
pp. 2964-2968
Author(s):  
顾黎明 Gu Liming ◽  
孙葆根 Sun Baogen ◽  
申超波 Shen Chaobo ◽  
卢平 Lu Ping ◽  
王季刚 Wang Jigang ◽  
...  
Keyword(s):  
Measurement System ◽  
Photon Beam ◽  
Position Measurement ◽  
Beam Position ◽  
Four Quadrant

scholarly journals High Precision Position Measurement Method for Laguerre-Gaussian Beams Using a Quadrant Detector

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 4007 ◽  
Author(s):  
Qian Li ◽  
Jiabin Wu ◽  
Yunshan Chen ◽  
Jingyuan Wang ◽  
Shijie Gao ◽  
...  
Keyword(s):  
Maximum Error ◽  
Least Square ◽  
New Method ◽  
Beam Radius ◽  
Engineering Practice ◽  
Gaussian Beams ◽  
Good Prospect ◽  
Position Measurement ◽  
Beam Position ◽  
Mean Square Errors

In this paper, we propose a new method to improve the position measurement accuracy for Laguerre-Gaussian beams on a quadrant detector (QD). First, the error effects of the detector diameter and the gap size are taken into account, and the position error compensation factor is introduced into the conventional formula. Then, in order to reduce the number of parameters, the concept of effective radius is proposed. Thus, a new analytical expression is obtained with a best fit using the least square method. It is verified by simulation that this approach can reduce the maximum error by 97.4% when the beam radius is 0.95 mm; meanwhile, the root mean square errors under different radii are all less than 0.004 mm. The results of simulation show that the new method could effectively improve the accuracy of the QD measurement for different radii. Therefore, the new method would have a good prospect in the engineering practice of beam position measurements.

Spatio-temporal measurement of beam properties in the PLS diagnostic beamline

1998 ◽  
Vol 5 (3) ◽  
pp. 642-644 ◽  
Author(s):  
J. Y. Huang ◽  
I. S. Ko
Keyword(s):  
Visible Light ◽  
Imaging System ◽  
Ccd Camera ◽  
Photon Beam ◽  
Transverse Beam ◽  
Beam Position ◽  
X Ray ◽  
X Ray Imaging ◽  
Visible Light Imaging ◽  
Temporal Measurement

A diagnostic beamline is being constructed in the PLS storage ring for measurement of electron- and photon-beam properties. It consists of two 1:1 imaging systems: a visible-light imaging system and a soft X-ray imaging system. In the visible-light imaging system, the transverse beam size and beam position are measured with various detectors: a CCD camera, two photodiode arrays and a photon-beam position monitor. Longitudinal bunch structure is also investigated with a fast photodiode detector and a picosecond streak camera. On the other hand, the soft X-ray imaging system is under construction to measure beam sizes with negligible diffraction-limited error. The X-ray image optics consist of a flat cooled mirror and two spherical focusing mirrors.

Photon-beam-position-monitor in PLS Diagnostic Beamline

2010 ◽  
Vol 56 (6(1)) ◽  
pp. 1981-1984 ◽  
Author(s):  
Changbum Kim ◽  
Jong Chel Yoon ◽  
Seung-nam Kim ◽  
Myong-jin Kim ◽  
Hee Seob Kim ◽  
...  
Keyword(s):  
Photon Beam ◽  
Beam Position Monitor ◽  
Beam Position

scholarly journals Proton beam position measurement in air using a BPM

AIP Advances ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 095023
Author(s):  
Prabir K. Roy ◽  
John W. Lewellen ◽  
Levi P. Neukirch ◽  
Heath A. Watkins
Keyword(s):  
Proton Beam ◽  
Position Measurement ◽  
Beam Position

CALCULATION OF NONLINEAR TUNE SHIFT USING BEAM POSITION MEASUREMENT RESULTS

2009 ◽  
Vol 24 (05) ◽  
pp. 974-986 ◽  
Author(s):  
PAVEL SNOPOK ◽  
MARTIN BERZ ◽  
CAROL JOHNSTONE
Keyword(s):  
Linear Optics ◽  
Position Measurement ◽  
Linear Lattice ◽  
Beam Position ◽  
Proposed Model ◽  
Measurement Results ◽  
Tune Shift ◽  
Form Transformation ◽  
Normal Form Transformation ◽  
Shift Calculation

The calculation of the nonlinear tune shift with amplitude based on the results of measurements and the linear lattice information is discussed. The tune shift is calculated based on a set of specific measurements and some extra information which is usually available, namely that about the size and particle distribution in the beam and the linear optics effect on the particles. The method to solve this problem uses the technique of normal form transformation. The proposed model for the nonlinear tune shift calculation is compared to both the numerical results for the nonlinear model of the Tevatron accelerator and the independent approximate formula for the tune shift by Meller et al. The proposed model shows a discrepancy of about 2%.

Application and design of photon beam position monitor in HLS

2005 ◽  
Author(s):  
Baogen Sun ◽  
Duohui He ◽  
Ping Lu ◽  
Yong Wang ◽  
Hongliang Xu ◽  
...  
Keyword(s):  
Photon Beam ◽  
Beam Position Monitor ◽  
Beam Position
Sign in / Sign up

Export Citation Format

Share Document