Variable gain, zero offset, dc coupled video amplifier for microwave detector diodes

1995 ◽  
Vol 66 (9) ◽  
pp. 4694-4697 ◽  
Author(s):  
J. Mathew
Keyword(s):  
Variable Gain ◽  
Microwave Detector ◽  
Video Amplifier ◽  
Zero Offset

Video-Enhanced Microscopy--Better Visibility of Plant Cell Structures

1982 ◽  
Vol 40 ◽  
pp. 182-185
Author(s):  
N.S. Allen ◽  
R.D. Allen
Keyword(s):  
Diffraction Pattern ◽  
Theoretical Basis ◽  
Numerical Aperture ◽  
Gain Control ◽  
Control Unit ◽  
Camera Control ◽  
Variable Gain ◽  
Contrast Method ◽  
Fine Detail ◽  
Cell Structures

Various methods of video-enhanced microscopy combine TV cameras with light microscopes creating images with improved resolution, contrast and visibility of fine detail, which can be recorded rapidly and relatively inexpensively. The AVEC (Allen Video-enhanced Contrast) method avoids polarizing rectifiers, since the microscope is operated at retardations of λ/9- λ/4, where no anomaly is seen in the Airy diffraction pattern. The iris diaphram is opened fully to match the numerical aperture of the condenser to that of the objective. Under these conditions, no image can be realized either by eye or photographically. Yet the image becomes visible using the Hamamatsu C-1000-01 binary camera, if the camera control unit is equipped with variable gain control and an offset knob (which sets a clamp voltage of a D.C. restoration circuit). The theoretical basis for these improvements has been described.

The DQE of an electron image recording system

1978 ◽  
Vol 36 (1) ◽  
pp. 100-101
Author(s):  
K.-H. Herrmann ◽  
D. Krahl ◽  
H.-P Rust
Keyword(s):  
Primary Electron ◽  
Ideal Case ◽  
Image Recording ◽  
Main Requirement ◽  
High Detection ◽  
Electron Image ◽  
Video Amplifier ◽  
Detection Quantum Efficiency ◽  
Selection Of ◽  
The Ideal

The high detection quantum efficiency (DQE) is the main requirement for an imagerecording system used in electron microscopy of radiation-sensitive specimens. An electronic TV system of the type shown in Fig. 1 fulfills these conditions and can be used for either analog or digital image storage and processing [1], Several sources of noise may reduce the DQE, and therefore a careful selection of various elements is imperative.The noise of target and of video amplifier can be neglected when the converter stages produce sufficient target electrons per incident primary electron. The required gain depends on the type of the tube and also on the type of the signal processing chosen. For EBS tubes, for example, it exceeds 10. The ideal case, in which all impinging electrons create uniform charge peaks at the target, is not obtainable for several reasons, and these will be discussed as they relate to a system with a scintillator, fiber-optic and photo-cathode combination as the first stage.

Low-Voltage Variable Gain Current Amplifier for High-Voltage Signal Processing

2009 ◽  
Vol 129 (8) ◽  
pp. 1511-1517
Author(s):  
Nicodimus Retdian ◽  
Jieting Zhang ◽  
Takahide Sato ◽  
Shigetaka Takagi
Keyword(s):  
Signal Processing ◽  
High Voltage ◽  
Low Voltage ◽  
Current Amplifier ◽  
Variable Gain ◽  
Voltage Signal

A High Efficiency Variable Gain Amplifier Circuit with Controllable Transconductance Amp

2009 ◽  
Vol 129 (10) ◽  
pp. 1968-1969
Author(s):  
Tetsuro Okura ◽  
Shunsuke Okura ◽  
Toru Ido ◽  
Kenji Taniguchi
Keyword(s):  
High Efficiency ◽  
Variable Gain Amplifier ◽  
Amplifier Circuit ◽  
Variable Gain

A Fully Differential Variable Gain Amplifier for Portable Impedance Sensing Applications

2019 ◽  
Vol 7 ◽  
Author(s):  
Jorge Pérez Bailón ◽  
Jaime Ramírez-Angulo ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Power Consumption ◽  
Active Area ◽  
Variable Gain Amplifier ◽  
Cmos Process ◽  
Current Steering ◽  
Impedance Sensing ◽  
Variable Gain ◽  
Fully Differential ◽  
Sensing Applications ◽  
Constant Bandwidth

This paper presents a Variable Gain Amplifier (VGA) designed in a 0.18 μm CMOS process to operate in an impedance sensing interface. Based on a transconductance-transimpedance (TC-TI) approach with intermediate analog-controlled current steering, it exhibits a gain ranging from 5 dB to 38 dB with a constant bandwidth around 318 kHz, a power consumption of 15.5 μW at a 1.8 V supply and an active area of 0.021 mm2.

Sign in / Sign up

Export Citation Format

Share Document