Diamond crystallite formation on Si(100) from the gas phase: Seeding or heterogeneous nucleation?

1992 ◽  
Vol 61 (11) ◽  
pp. 1287-1289 ◽  
Author(s):  
E. Molinari ◽  
R. Polini ◽  
M. Tomellini
Keyword(s):  
Gas Phase ◽  
Heterogeneous Nucleation ◽  
Diamond Crystallite

Direct Nucleation of Crystalline SiGe on Substrates by Reactive Thermal CVD with Si2H6 and GeF4

1997 ◽  
Vol 467 ◽  
Author(s):  
Fumio Yoshizawa ◽  
Kunihiro Shiota ◽  
Daisuke Inoue ◽  
Jun-ichi Hanna
Keyword(s):  
Growth Rate ◽  
Gas Phase ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Film Growth ◽  
Early Stage ◽  
Gaseous Mixture ◽  
The Other ◽  
Thermal Cvd ◽  
Initial Deposition

ABSTRACTPolycrystalline SiGe (poly-SiGe) film growth by reactive thermal CVD with a gaseous mixture of Si2H6 and GeF4 was investigated on various substrates such as Al,Cr, Pt, Si, ITO, ZnO and thermally grown SiO2.In Ge-rich film growth, SEM observation in the early stage of the film growth revealed that direct nucleation of crystallites took place on the substrates. The nucleation was governed by two different mechanisms: one was a heterogeneous nucleation on the surface and the other was a homogeneous nucleation in the gas phase. In the former case, the selective nucleation was observed at temperatures lower than 400°C on metal substrates and Si, where the activation of adsorbed GeF4 on the surface played a major role for the nuclei formation, leading to the selective film growth.On the other hand, the direct nucleation did not always take place in Si-rich film growth irrespective of the substrates and depended on the growth rate. In a growth rate of 3.6nm/min, the high crystallinity of poly-Si0.95Ge0.05in a 220nm-thick film was achieved at 450°C due to the no initial deposition of amorphous tissue on SiO2 substrates.

Heterogeneous nucleation of a monomer gas on a growing gas-phase polymer

1999 ◽  
Vol 110 (19) ◽  
pp. 9725-9729 ◽  
Author(s):  
Chaok Seok ◽  
David W. Oxtoby
Keyword(s):  
Gas Phase ◽  
Heterogeneous Nucleation

Residual Gas Reactions in the Electron Microscope: I. Qualitative Observations on the Water Gas Reaction

1968 ◽  
Vol 26 ◽  
pp. 292-293
Author(s):  
Richard E. Hartman ◽  
Roberta S. Hartman ◽  
Peter L. Ramos
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
Gas Phase ◽  
Absolute Temperature ◽  
Residual Gas ◽  
Gas Reactions ◽  
Image Position ◽  
The Right ◽  
Water Gas ◽  
Thinning Rate

The action of water and the electron beam on organic specimens in the electron microscope results in the removal of oxidizable material (primarily hydrogen and carbon) by reactions similar to the water gas reaction .which has the form:The energy required to force the reaction to the right is supplied by the interaction of the electron beam with the specimen.The mass of water striking the specimen is given by:where u = gH2O/cm2 sec, PH2O = partial pressure of water in Torr, & T = absolute temperature of the gas phase. If it is assumed that mass is removed from the specimen by a reaction approximated by (1) and that the specimen is uniformly thinned by the reaction, then the thinning rate in A/ min iswhere x = thickness of the specimen in A, t = time in minutes, & E = efficiency (the fraction of the water striking the specimen which reacts with it).

Amorphous silica coating on α-alumina particles

1995 ◽  
Vol 53 ◽  
pp. 210-211
Author(s):  
J. W. Mellowes ◽  
C. M. Chun ◽  
I. A. Aksay
Keyword(s):  
Amorphous Silica ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Silica Coating ◽  
Full Density ◽  
Optimal Conditions ◽  
Fine Grained ◽  
Alumina Particles ◽  
Complete Mullitization ◽  
Powder Compacts

Mullite (3Al2O32SiO2) can be fabricated by transient viscous sintering using composite particles which consist of inner cores of a-alumina and outer coatings of amorphous silica. Powder compacts prepared with these particles are sintered to almost full density at relatively low temperatures (~1300°C) and converted to dense, fine-grained mullite at higher temperatures (>1500°C) by reaction between the alumina core and the silica coating. In order to achieve complete mullitization, optimal conditions for coating alumina particles with amorphous silica must be achieved. Formation of amorphous silica can occur in solution (homogeneous nucleation) or on the surface of alumina (heterogeneous nucleation) depending on the degree of supersaturation of the solvent in which the particles are immersed. Successful coating of silica on alumina occurs when heterogeneous nucleation is promoted and homogeneous nucleation is suppressed. Therefore, one key to successful coating is an understanding of the factors such as pH and concentration that control silica nucleation in aqueous solutions. In the current work, we use TEM to determine the optimal conditions of this processing.

Integration of Core-Edge Spectroscopy Methods for the Study of Polymers

1996 ◽  
Vol 54 ◽  
pp. 154-155
Author(s):  
E. G. Rightor
Keyword(s):  
Excited State ◽  
Polymer Blends ◽  
Gas Phase ◽  
Spatial Resolution ◽  
High Spatial Resolution ◽  
Electronic States ◽  
Core Electron ◽  
Bulk Solids ◽  
Development Application

Core edge spectroscopy methods are versatile tools for investigating a wide variety of materials. They can be used to probe the electronic states of materials in bulk solids, on surfaces, or in the gas phase. This family of methods involves promoting an inner shell (core) electron to an excited state and recording either the primary excitation or secondary decay of the excited state. The techniques are complimentary and have different strengths and limitations for studying challenging aspects of materials. The need to identify components in polymers or polymer blends at high spatial resolution has driven development, application, and integration of results from several of these methods.

Sign in / Sign up

Export Citation Format

Share Document