scholarly journals Experimental investigation of the tribological behaviour of carbon and low-alloy steels sliding against HSS

2014 ◽  
Vol 16 (1) ◽  
pp. 109 ◽  
Author(s):  
Riadh Autay ◽  
Mounir Kchaou ◽  
Fakhreddine Dammak
Keyword(s):  
Experimental Investigation ◽  
Low Alloy Steels ◽  
Tribological Behaviour ◽  
Alloy Steels

scholarly journals Machinability Studies of Low Alloy Steels by Face Turning Method: An Experimental Investigation

2013 ◽  
Vol 64 ◽  
pp. 632-641 ◽  
Author(s):  
Rajshekhar Lalbondre ◽  
Prasad Krishna ◽  
G.C. Mohankumar
Keyword(s):  
Experimental Investigation ◽  
Low Alloy Steels ◽  
Alloy Steels

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Materials for bullet core

2020 ◽  
Vol 2020 (10) ◽  
pp. 8-21
Author(s):  
A. G. Kolmakov ◽  
◽  
I. O. Bannykh ◽  
V. I. Antipov ◽  
L. V. Vinogradov ◽  
...  
Keyword(s):  
High Speed ◽  
Bending Strength ◽  
Low Alloy Steels ◽  
Hard Alloys ◽  
Small Arms ◽  
Alloy Steels ◽  
Materials Used ◽  
Basic Ideas ◽  
New Generation ◽  
Natural Composite

he basic ideas about the process of introducing cores into protective barriers and the most common core patterns and their location in conventional and sub-caliber small arms bullets are discussed. The materials used for manufacture of cores are analyzed. It is concluded that for mass bullets of increased armor penetration the most rational choice can be considered the use of high-carbon low-alloy steels of a new generation with a natural composite structure and hardness of up to 70 HRC. For specialized armor-piercing bullets, cores made from promising economically-alloyed high-speed steels characterized by a high complex of «hardness—bending strength» are better alternative than ones made of hard alloys or tungsten alloys.

Sign in / Sign up

Export Citation Format

Share Document