scholarly journals COMPARISON BETWEEN TRADITIONAL MINERALOGICAL AND COMPUTERIZED RATIONAL ANALYSIS OF CERAMIC RAW MATERIALS

1986 ◽  
Vol 47 (C1) ◽  
pp. C1-57-C1-62
Author(s):  
B. FABRI ◽  
C. FIORI ◽  
A. KRAJEWSKI ◽  
R. VALMORI ◽  
A. TENAGLIA
Keyword(s):  
Raw Materials ◽  
Rational Analysis

Clays from Southern Brazil: Physical, Chemical and Mineralogical Characterization

2005 ◽  
Vol 498-499 ◽  
pp. 447-452 ◽  
Author(s):  
Sivaldo Leite Correia ◽  
K.A.S. Curto ◽  
Dachamir Hotza ◽  
Ana M. Segadães
Keyword(s):  
Raw Materials ◽  
X Ray Diffraction ◽  
Rational Analysis ◽  
Porto Alegre ◽  
Mineralogical Characterization ◽  
X Ray ◽  
Muscovite Mica ◽  
Production Stages ◽  
Ceramics Industry

Fore knowledge of the characteristics of ceramic raw materials is of utmost importance during the development, processing and production stages of any ceramic product. This work describes the characterization of clays commonly used in the ceramics industry. Two different clays were selected: clay A, from Tubarão-SC and clay B, from Porto Alegre-RS. Their chemical composition was obtained by X-ray fluorescence and their mineralogy by X-ray diffraction, coupled with numerical rational analysis. Their thermal behaviour was studied by differential thermal analysis and thermogravimetry. Their particle size distribution and plasticity were also determined. Clay A showed circa 47.5 % quartz (by weight), 40.2 % kaolinite and 9.9 % muscovite mica. Clay B showed a high kaolinite content (circa 72 wt.%), accompanied by montmorillonite (circa 10 %) and potash feldspar (circa 10 % microcline). Clay B was found to be much more plastic than clay A, and both are suitable for pottery, tiles and brick making.

Microstructural characterization of laser-melted/roller-quenched dicalcium silicate

1988 ◽  
Vol 46 ◽  
pp. 582-583
Author(s):  
C. J. Chan ◽  
K. R. Venkatachari ◽  
W. M. Kriven ◽  
J. F. Young
Keyword(s):  
Particle Size ◽  
Raw Materials ◽  
Shape Change ◽  
Microstructural Characterization ◽  
Particle Size Effect ◽  
Dicalcium Silicate ◽  
Laser Melting ◽  
Uniform Size ◽  
Cell Shape Change ◽  
Wide Range

Dicalcium silicate (Ca2SiO4) is a major component of Portland cement. It has also been investigated as a potential transformation toughener alternative to zirconia. It has five polymorphs: α, α'H, α'L, β and γ. Of interest is the β-to-γ transformation on cooling at about 490°C. This transformation, accompanied by a 12% volume increase and a 4.6° unit cell shape change, is analogous to the tetragonal-to-monoclinic transformation in zirconia. Due to the processing methods used, previous studies into the particle size effect were limited by a wide range of particle size distribution. In an attempt to obtain a more uniform size, a fast quench rate involving a laser-melting/roller-quenching technique was investigated.The laser-melting/roller-quenching experiment used precompacted bars of stoichiometric γ-Ca2SiO4 powder, which were synthesized from AR grade CaCO3 and SiO2xH2O. The raw materials were mixed by conventional ceramic processing techniques, and sintered at 1450°C. The dusted γ-Ca2SiO4 powder was uniaxially pressed into 0.4 cm x 0.4 cm x 4 cm bars under 34 MPa and cold isostatically pressed under 172 MPa. The γ-Ca2SiO4 bars were melted by a 10 KW-CO2 laser.

Crystallization of barium hexaferrite

1992 ◽  
Vol 50 (1) ◽  
pp. 362-363
Author(s):  
Chung-kook Lee ◽  
Yolande Berta ◽  
Robert F. Speyer
Keyword(s):  
Size Distribution ◽  
Raw Materials ◽  
Barium Hexaferrite ◽  
Recording Media ◽  
Magnetic Recording Media ◽  
Promising Candidate ◽  
Crystallization Method ◽  
Temperature Heat ◽  
High Density Magnetic Recording ◽  
Temperature Heat Treatment

Barium hexaferrite (BaFe12O19) is a promising candidate for high density magnetic recording media due to its superior magnetic properties. For particulate recording media, nano-sized single crystalline powders with a narrow size distribution are a primary application requirement. The glass-crystallization method is preferred because of the controllability of crystallization kinetics, hence, particle size and size distribution. A disadvantage of this method is the need to melt raw materials at high temperatures with non-reactive crucibles, e.g. platinum. However, in this work, we have shown that crystal growth of barium hexaferrite occurred during low temperature heat treatment of raw batches.

A Rational Analysis of Constructed Preference

2014 ◽  
Author(s):  
Shlomi Sher ◽  
Johannes Muller-Trede ◽  
Craig R. M. McKenzie
Keyword(s):  
Rational Analysis
Sign in / Sign up

Export Citation Format

Share Document