Comparison of macroscopic mechanical properties and shear band characteristics established by acoustic emission measurements in Fe85-xCoxB15 amorphous alloys ribbons

2001 ◽  
Vol 11 (PR5) ◽  
pp. Pr5-259-Pr5-265 ◽  
Author(s):  
E. D. Tabachnikova ◽  
A. Yu. Vinogradov
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Shear Band ◽  
Amorphous Alloys

Study on mechanical properties and damage evolution of carbonaceous shale under triaxial compression with acoustic emission

2021 ◽  
pp. 105678952199119
Author(s):  
Kai Yang ◽  
Qixiang Yan ◽  
Chuan Zhang ◽  
Wang Wu ◽  
Fei Wan
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Water Content ◽  
Damage Evolution ◽  
Damage Assessment ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Damage Variable ◽  
Natural State ◽  
Carbonaceous Shale

To explore the mechanical properties and damage evolution characteristics of carbonaceous shale with different confining pressures and water-bearing conditions, triaxial compression tests accompanied by simultaneous acoustic emission (AE) monitoring were conducted on carbonaceous shale rock specimens. The AE characteristics of carbonaceous shale were investigated, a damage assessment method based on Shannon entropy of AE was further proposed. The results suggest that the mechanical properties of carbonaceous shale intensify with increasing confining pressure and degrade with increasing water content. Moisture in rocks does not only weaken the cohesion but also reduce the internal friction angle of carbonaceous shale. It is observed that AE activities mainly occur in the post-peak stage and the strong AE activities of saturated carbonaceous shale specimens appear at a lower normalized stress level than that of natural-state specimens. The maximum AE counts and AE energy increase with water content while decrease with confining pressure. Both confining pressure and water content induce changes in the proportions of AE dominant frequency bands, but the changes caused by confining pressure are more significant than those caused by water content. The results also indicate that AE entropy can serve as an applicable index for rock damage assessment. The damage evolution process of carbonaceous shale can be divided into two main stages, including the stable damage development stage and the damage acceleration stage. The damage variable increases slowly accompanied by a few AE activities at the first stage, which is followed by a rapid growth along with intense acoustic emission activities at the damage acceleration stage. Moreover, there is a sharp rise in the damage evolution curve for the natural-state specimen at the damage acceleration stage, while the damage variable develops slowly for the saturated-state specimen.

scholarly journals Acoustic Emission and K-S Metric Entropy as Methods for Determining Mechanical Properties of Composite Materials

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 145
Author(s):  
Lesław Kyzioł ◽  
Katarzyna Panasiuk ◽  
Grzegorz Hajdukiewicz ◽  
Krzysztof Dudzik
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Composite Material ◽  
Composite Materials ◽  
Testing Machine ◽  
Measurement Data ◽  
Entropy Method ◽  
Displacement Sensor ◽  
Metric Entropy ◽  
Plastic Phase

Due to the unique properties of polymer composites, these materials are used in many industries, including shipbuilding (hulls of boats, yachts, motorboats, cutters, ship and cooling doors, pontoons and floats, torpedo tubes and missiles, protective shields, antenna masts, radar shields, and antennas, etc.). Modern measurement methods and tools allow to determine the properties of the composite material, already during its design. The article presents the use of the method of acoustic emission and Kolmogorov-Sinai (K-S) metric entropy to determine the mechanical properties of composites. The tested materials were polyester-glass laminate without additives and with a 10% content of polyester-glass waste. The changes taking place in the composite material during loading were visualized using a piezoelectric sensor used in the acoustic emission method. Thanks to the analysis of the RMS parameter (root mean square of the acoustic emission signal), it is possible to determine the range of stresses at which significant changes occur in the material in terms of its use as a construction material. In the K-S entropy method, an important measuring tool is the extensometer, namely the displacement sensor built into it. The results obtained during the static tensile test with the use of an extensometer allow them to be used to calculate the K-S metric entropy. Many materials, including composite materials, do not have a yield point. In principle, there are no methods for determining the transition of a material from elastic to plastic phase. The authors showed that, with the use of a modern testing machine and very high-quality instrumentation to record measurement data using the Kolmogorov-Sinai (K-S) metric entropy method and the acoustic emission (AE) method, it is possible to determine the material transition from elastic to plastic phase. Determining the yield strength of composite materials is extremely important information when designing a structure.

scholarly journals The effect of liquid nitrogen cooling on coal cracking and mechanical properties

2018 ◽  
Vol 36 (6) ◽  
pp. 1609-1628 ◽  
Author(s):  
Chengzheng Cai ◽  
Feng Gao ◽  
Yugui Yang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Acoustic Emission ◽  
Liquid Nitrogen ◽  
Wave Velocity ◽  
Count Rate ◽  
Initial State ◽  
Nitrogen Injection ◽  
Strength Tests ◽  
Liquid Nitrogen Cooling

Liquid nitrogen is a type of super-cryogenic fluid, which can cause the reservoir temperature to decrease significantly and thereby induce formation rock damage and cracking when it is injected into the wellbore as fracturing fluid. An experimental set-up was designed to monitor the acoustic emission signals of coal during its contact with cryogenic liquid nitrogen. Ultrasonic and tensile strength tests were then performed to investigate the effect of liquid nitrogen cooling on coal cracking and the changes in mechanical properties thereof. The results showed that acoustic emission phenomena occurred immediately as the coal sample came into contact with liquid nitrogen. This indicated that evident damage and cracking were induced by liquid nitrogen cooling. During liquid nitrogen injection, the ring-down count rate was high, and the cumulative ring-down counts also increased rapidly. Both the ring-down count rate and the cumulative ring-down counts during liquid nitrogen injection were much greater than those in the post-injection period. Liquid nitrogen cooling caused the micro-fissures inside the coal to expand, leading to a decrease in wave velocity and the deterioration in mechanical strength. The wave velocity, which was measured as soon as the sample was removed from the liquid nitrogen (i.e. the wave velocity was recorded in the cooling state), decreased by 14.46% on average. As the cryogenic samples recovered to room temperature, this value increased to 18.69%. In tensile strength tests, the tensile strengths of samples in cooling and cool-treated states were (on average) 17.39 and 31.43% less than those in initial state. These indicated that both during the cooling and heating processes, damage and cracking were generated within these coal samples, resulting in the acoustic emission phenomenon as well as the decrease in wave velocity and tensile strength.

Plastic Deformation-Induced Nanocrystalline Aluminum in Al-Based Amorphous Alloys

1993 ◽  
Vol 321 ◽  
Author(s):  
H. Chen ◽  
Y. He ◽  
G. J. Shiflet ◽  
S. J. Poon
Keyword(s):  
Plastic Deformation ◽  
Amorphous Alloy ◽  
Shear Band ◽  
Thin Layer ◽  
Ball Milling ◽  
Direct Observation ◽  
Amorphous Alloys ◽  
Shear Bands ◽  
Amorphous Ribbons ◽  
Nanocrystalline Aluminum

ABSTRACTWe report the first direct observation of crystallization induced in the slipped planes of aluminum based amorphous alloys by bending the amorphous ribbons. Nanometer-sized crystalline precipitates are found exclusively within a thin layer (shear band) in the slipped planes extending across the deformed amorphous alloy ribbons. It is also found that the nanocrystalline aluminum can be produced by ball-Milling. It is likely that local atomic rearrangements within the shear bands create the nanocrystals which appear after plastic deformation.

scholarly journals Comparison of Mechanical Behavior and Acoustic Emission Characteristics of Three Thermally-Damaged Rocks

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2350 ◽  
Author(s):  
Jun Peng ◽  
Sheng-Qi Yang
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Mechanical Behavior ◽  
Thermal Damage ◽  
Strain Curve ◽  
Treatment Temperature ◽  
P Wave ◽  
High Temperature Treatment ◽  
High Porosity ◽  
Compression Tests

High temperature treatment has a significant influence on the mechanical behavior and the associated microcracking characteristic of rocks. A good understanding of the thermal damage effects on rock behavior is helpful for design and stability evaluation of engineering structures in the geothermal field. This paper studies the mechanical behavior and the acoustic emission (AE) characteristic of three typical rocks (i.e., sedimentary, metamorphic, and igneous), with an emphasis on how the difference in rock type (i.e., porosity and mineralogical composition) affects the rock behavior in response to thermal damage. Compression tests are carried out on rock specimens which are thermally damaged and AE monitoring is conducted during the compression tests. The mechanical properties including P-wave velocity, compressive strength, and Young’s modulus for the three rocks are found to generally show a decreasing trend as the temperature applied to the rock increases. However, these mechanical properties for quartz sandstone first increase to a certain extent and then decrease as the treatment temperature increases, which is mainly attributed to the high porosity of quartz sandstone. The results obtained from stress–strain curve, failure mode, and AE characteristic also show that the failure of quartz-rich rock (i.e., quartz sandstone and granite) is more brittle when compared with that of calcite-rich rock (i.e., marble). However, the ductility is enhanced to some extent as the treatment temperature increases for all the three examined rocks. Due to high brittleness of quartz sandstone and granite, more AE activities can be detected during loading and the recorded AE activities mostly accumulate when the stress approaches the peak strength, which is quite different from the results of marble.

scholarly journals Mechanical Properties of Ni-Zr and Ni-B Amorphous Alloys

1989 ◽  
Vol 53 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Toshio Nasu ◽  
Kunio Nagaoka ◽  
Yoshiyuki Tomitsuka ◽  
Hideki Niwa ◽  
Isao Ajiki ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Amorphous Alloys

Acoustic emission and mechanical properties of trabecular bone

Biomaterials ◽  
1985 ◽  
Vol 6 (4) ◽  
pp. 218-224 ◽  
Author(s):  
Jocelyn G. Wells ◽  
Rees D. Rawlings
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Trabecular Bone

scholarly journals Physical and mechanical rock properties of a heterogeneous volcano; the case of Mount Unzen, Japan

2020 ◽  
Author(s):  
Jackie E. Kendrick ◽  
Lauren N. Schaefer ◽  
Jenny Schauroth ◽  
Andrew F. Bell ◽  
Oliver D. Lamb ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Acoustic Emission ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
B Value ◽  
Coda Wave ◽  
Damage Accrual ◽  
The Impact

Abstract. Volcanoes represent one of the most critical geological settings for hazard modelling due to their propensity to both unpredictably erupt and collapse, even in times of quiescence. Volcanoes are heterogeneous at multiple scales, from porosity which is variably distributed and frequently anisotropic to strata that are laterally discontinuous and commonly pierced by fractures and faults. Due to variable and, at times, intense stress and strain conditions during and post-emplacement, volcanic rocks span an exceptionally wide range of physical and mechanical properties. Understanding the constituent materials' attributes is key to improving the interpretation of hazards posed by the diverse array of volcanic complexes. Here, we examine the spectrum of physical and mechanical properties presented by a single dome-forming eruption at a dacitic volcano, Mount Unzen (Japan) by testing a number of isotropic and anisotropic lavas in tension and compression and using monitored acoustic emission (AE) analysis. The lava dome was erupted as a series of 13 lobes between 1991–1995, and its ongoing instability means much of the volcano and its surroundings remain within an exclusion zone today. During a field campaign in 2015, we selected 4 representative blocks as the focus of this study. The core samples from each block span range in porosity from 9.14 to 42.81 %, and permeability ranges from 1.54 × 10−14 to 2.67 × 10−10 m2 (from 1065 measurements). For a given porosity, sample permeability varies by > 2 orders of magnitude is lower for macroscopically anisotropic samples than isotropic samples of similar porosity. An additional 379 permeability measurements on planar block surfaces ranged from 1.90 × 10−15 to 2.58 × 10−12 m2, with a single block having higher standard deviation and coefficient of variation than a single core. Permeability under confined conditions showed that the lowest permeability samples, whose porosity largely comprises microfractures, are most sensitive to effective pressure. The permeability measurements highlight the importance of both scale and confinement conditions in the description of permeability. The uniaxial compressive strength (UCS) ranges from 13.48 to 47.80 MPa, and tensile strength (UTS) using the Brazilian disc method ranges from 1.30 to 3.70 MPa, with crack-dominated lavas being weaker than vesicle-dominated materials of equivalent porosity. UCS is lower in saturated conditions, whilst the impact of saturation on UTS is variable. UCS is between 6.8 and 17.3 times higher than UTS, with anisotropic samples forming each end member. The Young's modulus of dry samples ranges from 4.49 to 21.59 GPa and is systematically reduced in water-saturated tests. The interrelation of porosity, UCS, UTS and Young's modulus was modelled with good replication of the data. Acceleration of monitored acoustic emission (AE) rates during deformation was assessed by fitting Poisson point process models in a Bayesian framework. An exponential acceleration model closely replicated the tensile strength tests, whilst compressive tests tended to have relatively high early rates of AEs, suggesting failure forecast may be more accurate in tensile regimes, though with shorter warning times. The Gutenberg-Richter b-value has a negative correlation with connected porosity for both UCS and UTS tests which we attribute to different stress intensities caused by differing pore networks. b-value is higher for UTS than UCS, and typically decreases (positive Δb) during tests, with the exception of cataclastic samples in compression. Δb correlates positively with connected porosity in compression, and negatively in tension. Δb using a fixed sampling length may be a more useful metric for monitoring changes in activity at volcanoes than b-value with an arbitrary starting point. Using coda wave interferometry (CWI) we identify velocity reductions during mechanical testing in compression and tension, the magnitude of which is greater in more porous samples in UTS but independent of porosity in UCS, and which scales to both b-value and Δb. Yet, saturation obscures velocity changes caused by evolving material properties, which could mask damage accrual or source migration in water-rich environments such as volcanoes. The results of this study highlight that heterogeneity and anisotropy within a single system not only add uncertainty but also have a defining role in the channelling of fluid flow and localisation of strain that dictate a volcano's hazards and the geophysical indicators we use to interpret them.

scholarly journals Influence of preliminary thermal aging on the residual interlayer strength and staging of damage accumulation in structural carbon plastic

2021 ◽  
pp. 41-51
Author(s):  
D. S Lobanov ◽  
E. M Lunegova ◽  
A. I Mugatarov
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Damage Accumulation ◽  
Elevated Temperatures ◽  
Energy Parameter ◽  
Carbon Plastic ◽  
Diagnostic Systems ◽  
Static Tests ◽  
Interlayer Shear ◽  
Short Beam

Aging of composites is a pervasive problem that leads to mechanical properties degradation, reduced design life of a structure and premature accidental failure. The work is devoted to an experimental study of the preliminary temperature aging effect on the residual mechanical properties of structural CFRP. The joint use of test systems and systems for registration and analysis of acoustic emission signals was applied. The Short Beam Shear Test of CFRP specimens were carried out using the short beam method. The tests were carried out on universal electromechanical systems Instron 5882 and Instron 5965 in accordance with the recommendations of ASTM D2344. In the process of loading the samples were continuously recorded by using the acoustic emission signals system AMSY-6. A piezoelectric sensor with a frequency range of 300-800 kHz was used. The test and diagnostic systems were synchronized during the tests. In the course of the work the values of the interlayer shear strength were determined for the samples of CFRP. Typical types of the sample destruction are illustrated. When analyzing the change in the mechanical properties of the carbon fiber reinforced plastic from a temperature increase the critical values of temperatures were established in which a sharp decline in the strength and elastic characteristics of materials occurs due to an active destruction of the binder. The graphs of the energy parameter dependence and frequency characteristics of acoustic emission signals on time have been constructed and analyzed. The estimate of the processes of damage accumulation in composites is carried out. The change of the damage accumulation mechanisms was illustrated. The obtained results illustrate the effect of elevated temperatures and the duration of their impact on the mechanical behavior of structural CFRP specimens during the static tests for the interlayer shear.

Sign in / Sign up

Export Citation Format

Share Document