scholarly journals Failure in a composite resin-dentin adhesive bond

1993 ◽  
Vol 03 (C7) ◽  
pp. C7-1065-C7-1067
Author(s):  
B. REZGUI ◽  
H. ABDENNAGI ◽  
S. SAHTOUT ◽  
M. S. BELKHIR
Keyword(s):  
Composite Resin ◽  
Adhesive Bond ◽  
Dentin Adhesive

Shear Strength of the Composite Bond to Etched Porcelain

1987 ◽  
Vol 66 (9) ◽  
pp. 1460-1465 ◽  
Author(s):  
I. Stangel ◽  
D. Nathanson ◽  
C.S. Hsu
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Surface Condition ◽  
Surface Configuration ◽  
Significant Difference ◽  
Laminate Veneers ◽  
Unfilled Resin ◽  
Scanning Electron ◽  
Dentin Adhesive

The shear bond strength of composite resin to porcelain was investigated to optimize variables for bonding porcelain laminate veneers. Scanning electron microscopy was initially used to examine the surface configuration of porcelain prepared under various conditions. A factorial experiment was undertaken to determine the effects of three different bonding methods on both etched and non-etched porcelain. Composite resin was bonded to the porcelain groups using (a) unfilled resin, (b) silane, and (c) silane with dentin adhesive. The results indicated a significant difference in shear bond strength for the three bonding groups, depending on the porcelain surface condition. For the unetched samples, significant differences in bond strength were obtained for all three bonding conditions. However, for the etched group, there were no differences between the silane and silane-with-dentin-adhesive groups. Porcelain etching significantly increased bond strength across all three bonding methods and was the main contributor to the obtained values.

Interfacial Chemistry of the Dentin/Adhesive Bond

2000 ◽  
Vol 79 (7) ◽  
pp. 1458-1463 ◽  
Author(s):  
P. Spencer ◽  
Y. Wang ◽  
M.P. Walker ◽  
D.M. Wieliczka ◽  
J.R. Swafford
Keyword(s):  
Adhesive Bond ◽  
Interfacial Chemistry ◽  
Dentin Adhesive

scholarly journals A New Solvent-free One-Step Self-Etch Adhesive: Bond Strength to Tooth Structures

2013 ◽  
Vol 14 (2) ◽  
pp. 269-274 ◽  
Author(s):  
Maryam Khoroushi ◽  
Farinaz Shirban ◽  
Mohammadreza Shirban
Keyword(s):  
Bond Strength ◽  
Gold Standard ◽  
Composite Resin ◽  
Adhesive Bond ◽  
Solvent Free ◽  
Enamel Surface ◽  
Dentin Surface ◽  
One Step ◽  
Adhesive Bond Strength ◽  
Self Etch

ABSTRACT Introduction In recent years some new solvent-free dental adhesives have been marketed. This study evaluated bonding effectiveness of a new one-step solvent-free self-etch adhesive in comparison with a common two-step self-etch adhesive used as gold standard. Materials and methods Flat enamel and dentin surfaces were prepared on 60 incisors using silicon carbide papers. Clearfil SE Bond (CSEB) and Bond 1SF (B1SF) adhesives were applied on enamel/dentin surfaces in four groups (n = 15): (1) Enamel surface and CSEB, (2) dentin surface and CSEB, (3) enamel surface and B1SF, (4) dentin surface and B1SF. Composite resin buildups were carried out using Z100 composite resin. All the specimens were stored for 24 hours at 37¢XC and 100% relative humidity. After 500 rounds of thermocycling, shear bond strength (SBS) test was performed using a universal testing machine at 1 mm/min crosshead speed. Data were analyzed with one-way ANOVA and a post hoc Tukey test (α = 0.05). In each experimental group, two additional specimens were prepared for scanning electron microscopy evaluation. Results Significant differences were observed between the study groups (p < 0.001). The highest enamel/dentin bond strengths were recorded in group 1 (CSEB) (p < 0.001). The SBS of the two-step self-etch adhesive to enamel and dentin was significantly higher than that of the one-step self-etch adhesive (p < 0.001). There was no significant difference between enamel and dentin SBS with B1SF (p = 0.559). Conclusion Within the limitations of the present study, when bonded to enamel and dentin the solvent-free adhesive B1SF underperforms as compared to CSEB as the control gold standard. How to cite this article Shirban F, Khoroushi M, Shirban M. A New Solvent-free One-Step Self-Etch Adhesive: Bond Strength to Tooth Structures. J Contemp Dent Pract 2013;14(2):269-274.

scholarly journals Shear Bond Strengths and Microleakage of Four Types of Dentin Adhesive Materials

2004 ◽  
Vol 5 (1) ◽  
pp. 63-73 ◽  
Author(s):  
Nasrien Z. Ateyah ◽  
Ahmed A. Elhejazi
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Composite Resin ◽  
Distilled Water ◽  
Bonding System ◽  
One Step ◽  
Diamond Saw ◽  
Bond Strengths ◽  
Adhesive Materials ◽  
Dentin Adhesive

Abstract The aim of this investigation was to compare the microleakage of composite resin (Z-100) and shear bond strength to bovine dentin using different types of adhesive systems (Scotch Bond Multi-Purpose, All-Bond 2, One-Step, and Perma Quick) to compare and correlate microleakage to shear bond strength. For the microleakage aspect of the study, 20 class V were prepared (bovine incisors) with 90-degree cavosurface margins and were located at the cemento-enamel junction using a template. Each dentin bonding system was applied to five cavities following the manufacturer's instructions and restored with Z-100 composite resin. After 24 hours of storage in distilled water at 37°C, the teeth were immersed in 2% basic fuchsin dye. All teeth were sectioned in a mesiodistal direction using a diamond saw, and each section was then inspected under a stereomacroscope. For the shear bond strength aspect of the study, 20 bovine incisors were centrally horizontally mounted in Teflon mold with cold cure acrylic resin. Flat labial dentin surfaces were prepared using different grit silicon carbide abrasive wheels. Five specimens were used for each of the bonding agent systems. Each specimen was bonded with restorative composite resin (Z-100) and applied to the treated dentinal surface through a split Teflon mold. All specimens were stored in distilled water at 37°C for 24 hours. The bonds were stressed using shear forces at a crosshead speed of 0.5mm/min using an Instron Universal testing machine. Findings indicate none of the systems tested in this study were free from microleakage. Scotch bond multipurpose achieved the best seal, with One-Step being second best, while All-Bond 2 and Perma Quick had the poorest seal. However, there were significant differences among the shear bond strengths of the four bonding systems tested. Scotch Bond Multi-Purpose has a higher bond strength to composite resin when compared to the other dentin adhesives. The study also concluded there is no association between microleakage and shear bond strength. Citation Ateyah AZ, Elhejazi AA. Shear Bond Strengths and Microleakage of Four Types of Dentin Adhesive Materials. J Contemp Dent Pract 2004 February;(5)1:063-073.

scholarly journals Cleaning and Conditioning of Contaminated Core Build-Up Material before Adhesive Bonding

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2880
Author(s):  
Karsten Klosa ◽  
Walid Shahid ◽  
Milda Aleknonytė-Resch ◽  
Matthias Kern
Keyword(s):  
Phosphoric Acid ◽  
Bond Strength ◽  
Adhesive Bonding ◽  
Composite Resin ◽  
Tensile Bond Strength ◽  
Air Abrasion ◽  
Powder Surface ◽  
Surface Conditioning ◽  
Alumina Particles ◽  
Dentin Adhesive

The objective of this study was to evaluate the effects of different cleaning and conditioning procedures after contamination on the tensile bond strength (TBS) of a luting resin to a core build-up composite resin. Specimens (n = 384) made of a core build-up material were stored for 3 weeks in 37 °C water. Half of the specimens were contaminated with saliva and a disclosing silicone and then cleaned either using phosphoric acid, a pumice suspension, air-abrasion with alumina or polishing powder. Surface conditioning was performed by either using a dentin adhesive, a silane containing primer or a composite resin primer, which resulted in 24 unique combinations of 16 specimens per group. Before measuring TBS, half of the specimens of each group were stored in 37 °C water for 3d or were artificially aged for 150 days. Results show that cleaning with pumice or air-abrasion are superior methods compared to using a polishing powder or phosphoric acid. Silane is an inferior conditioning agent compared to composite or dentin primers. Ideally, after contamination, bonding surfaces should be cleaned with a pumice suspension and conditioned with a dentin adhesive. Those surfaces could also be cleaned and conditioned with air-abrasion with alumina particles and a composite resin primer.

Adhesive bond integrity of Y‐TZP post with calcium fluoride infiltrated resin dentin adhesive: An SEM, EDX, FTIR and micro‐Raman study

2021 ◽  
Author(s):  
Eman M. AlHamdan ◽  
Samar Al‐Saleh ◽  
Mohammad H. AlRefeai ◽  
Imran Farooq ◽  
Eisha Abrar ◽  
...  
Keyword(s):  
Calcium Fluoride ◽  
Adhesive Bond ◽  
Raman Study ◽  
Dentin Adhesive

Total etch dentin bonding systems: scanning electron microscopy of the resin-dentin hybrid layer

1992 ◽  
Vol 50 (2) ◽  
pp. 1092-1093
Author(s):  
Jorge Perdigao
Keyword(s):  
Composite Resin ◽  
Mechanical Interlocking ◽  
Hybrid Layer ◽  
Agent Based ◽  
Dentin Bonding ◽  
Acid Agent ◽  
Bond Strengths ◽  
Main Component ◽  
Bonding Systems ◽  
New Generation

In 1955, Buonocore introduced the etching of enamel with phosphoric acid. Bonding to enamel was created by mechanical interlocking of resin tags with enamel prisms. Enamel is an inert tissue whose main component is hydroxyapatite (98% by weight). Conversely, dentin is a wet living tissue crossed by tubules containing cellular extensions of the dental pulp. Dentin consists of 18% of organic material, primarily collagen. Several generations of dentin bonding systems (DBS) have been studied in the last 20 years. The dentin bond strengths associated with these DBS have been constantly lower than the enamel bond strengths. Recently, a new generation of DBS has been described. They are applied in three steps: an acid agent on enamel and dentin (total etch technique), two mixed primers and a bonding agent based on a methacrylate resin. They are supposed to bond composite resin to wet dentin through dentin organic component, forming a peculiar blended structure that is part tooth and part resin: the hybrid layer.

Assessment of the effects of staining solutions, carbamide peroxide, and mouthwashes on color stability of composite resin

2014 ◽  
Vol 1 (2) ◽  
pp. 36-41
Author(s):  
Erica Crastechini ◽  
Paula de Siqueira Barbosa ◽  
Heleine Maria Chagas Rego ◽  
Priscila Holleben ◽  
Carlos Rocha Gomes Torres ◽  
...  
Keyword(s):  
Composite Resin ◽  
Color Stability ◽  
Carbamide Peroxide

Monobloco – cimentação de pino e preenchimento em único passo em dente tratado endodonticamente

2020 ◽  
Vol 10 (37) ◽  
pp. 10-19
Author(s):  
Patrícia Ferronato Araújo ◽  
Ana Carolina Portes Pasmadjian ◽  
Antonio Setsuo Sakamoto Junior
Keyword(s):  
Composite Resin ◽  
Case Reports ◽  
Single Step ◽  
Resin Cement ◽  
Endodontically Treated Teeth ◽  
Posterior Teeth ◽  
Elasticity Module ◽  
Post And Core Technique ◽  
Post And Core ◽  
Root Fiber

The literature reports several materials for the restoration of endodontically treated teeth, with coronal destruction that requires an intra-root fiber post to stabilize the prosthetic part. The intra-radicular post of composite resin reinforced with fiberglass can be used as retainers in rehabilitating endodontically treated teeth due to their adhesiveness, pleasing aesthetics, and elasticity module close to the dentin less wear on the remaining structure. This clinical case reports the step-by-step application of dual resin cement (Rebilda DC Dentine - Voco) used as the cementation material of the post and material for the filling core in a single step, in an upper right lateral incisor. Moreover, it describes the advantages and indications of the post-and-core technique, also called “monobloc” which can be used in both anterior and posterior teeth. This protocol minimizes the adhesive interfaces, the chair time, and the steps of the clinical procedure.

Técnica de mascaramento de substrato escurecido com lente de contato dental cimentada sobre faceta menos translúcida

2020 ◽  
Vol 10 (37) ◽  
pp. 38-45
Author(s):  
Lara Pepita de Souza Oliveira ◽  
Rebeka de Oliveira Reis ◽  
Ely Moacyr de Souza Portela ◽  
Sybilla Torres Dias ◽  
Cristiane Maria Brasil Leal
Keyword(s):  
Phosphoric Acid ◽  
Composite Resin ◽  
Intermediate Structure ◽  
Dental Ceramics ◽  
Central Incisor ◽  
Universal Adhesive ◽  
Patient Reported ◽  
Satisfaction With Treatment ◽  
Natural Teeth ◽  
Smile Aesthetics

Dental ceramics have an excellent ability to reproduce natural teeth appearance, but once the substrate has an altered coloration, it is necessary to mask this intercurrence, considering the characteristics of the ceramic and cement selected. This article aims to present a clinical case of rehabilitation with ceramic laminates to mask a darkened central incisor by planning a more opaque porcelain structure under a translucent contact lens. A female patient sought dental care complaining of dissatisfaction with smile aesthetics. It was clinically identified the presence of a Class IV darkened restoration in composite resin in element 11. In treatment planning harmony in the shape and color of elements 11 and 21 was aimed at through lithium disilicate lenses. An opaque intermediate structure was used to cover the darkening in tooth 11. The double molding technique was performed to obtain the working model. Prior to cementing, the surfaces were treated. In ceramics, conditioning with 10% hydrofluoric acid and 37% phosphoric acid, silane application and universal adhesive; in dental substrate, conditioning with 37% phosphoric acid and application of universal adhesive were performed. In laminates definitive cementation Allcem Venner cement was chosen. Patient reported satisfaction with treatment final aesthetics. Thus, cementation technique of a translucent laminate over an opaque facet is a good option for masking substrates with darkened coloration.

Sign in / Sign up

Export Citation Format

Share Document