CNC lathe comes with robot for unmanned production

1981 ◽  
Vol 60 (4) ◽  
pp. 2
Keyword(s):  
Cnc Lathe

THE EVALUATION OF SURFACE MORPHOLOGY USING FLEXURE GUIDED NANO-POSITIONING SYSTEM AND ULTRA-PRECISION LATHE

2012 ◽  
Vol 06 ◽  
pp. 172-177
Author(s):  
Nam-Su Kwak ◽  
Jae-Yeol Kim
Keyword(s):  
Surface Morphology ◽  
Piezoelectric Actuator ◽  
Control Method ◽  
Positioning System ◽  
Motion Error ◽  
Precision Stage ◽  
Cnc Lathe ◽  
Single Crystal Diamond ◽  
Ultra Precision ◽  
And Control

In this study, piezoelectric actuator, Flexure guide, Power transmission element and control method and considered for Nano-positioning system apparatus. The main objectives of this thesis were to develop the 3-axis Ultra-precision stages which enable the 3-axis control by the manipulation of the piezoelectric actuator and to enhance the precision of the Ultra-Precision CNC lathe which is responsible for the ductile mode machining of the hardened-brittle material where the machining is based on the single crystal diamond. Ultra-precision CNC lathe is used for machining and motion error of the machine are compensated by using 3-axis Ultra-precision stage. Through the simulation and experiments on ultra-precision positioning, stability and priority on Nano-positioning system with 3-axis ultra-precision stage and control algorithm are secured by using NI Labview. And after applying the system, is to analyze the surface morphology of the mold steel (SKD61)

Development of CAM System for 3D Surface Machining With CNC Lathe (Tool Path Generation Considering Acceleration)

2014 ◽  
Author(s):  
Keigo Takasugi ◽  
Katsuhiro Nakagaki ◽  
Yoshitaka Morimoto ◽  
Yoshiyuki Kaneko
Keyword(s):  
Lead Time ◽  
Internal Combustion Engines ◽  
Tool Path ◽  
Tool Path Generation ◽  
Combustion Engines ◽  
Determination Method ◽  
Experimental Procedure ◽  
Surface Machining ◽  
Cnc Lathe ◽  
Lathe Tool

This study developed a method called non-axisymmetric curved surface turning (NACS-Turning) for a CNC lathe composed of a turning axis and two translation axes. The NACS-Turning method controls the three axes synchronously. This new machining method can reduce the lead time for non-circular shapes such as cam profiles or pistons for internal combustion engines. In our previous report, we presented an outline of a machining principle and a CAM system for NACS-Turning. However, at the same time, we found the problem that the X-axis slide exceeds the allowable acceleration. Therefore, it is preferable that the acceleration is verified during the cam application, and the tool path is generated within the allowable acceleration range. Therefore, this paper first describes the determination method of machinable conditions for NACS-Turning in the cam application. Next, based on the result, relationships between the acceleration of the X-axis slide and machining conditions are clarified. Finally, the experimental procedure showed that our proposed method does not exceed the allowable acceleration of the X-axis slide.

Research on Several Key Techniques of Power Tool Rest Noise Detection System

2012 ◽  
Vol 630 ◽  
pp. 271-275
Author(s):  
Xiao Hong Lu ◽  
Yong Yan Shang ◽  
Peng Zhuo Han ◽  
Guang Jun Li ◽  
Wen Yi Wu
Keyword(s):  
Spectrum Analysis ◽  
Detection Method ◽  
Detection System ◽  
Sampled Data ◽  
Noise Detection ◽  
Machining Center ◽  
Cnc Lathe ◽  
Spectrum Transformation ◽  
Key Techniques

The scarcity and imperfection of power tool rest noise detection method have seriously limited the development of the industry of CNC lathe, lathe and milling composite machining center. A noise detection system based on LabVIEW is developed. The developed system adopts a noise sensor as noise detection component to test the noise information of the power tool rest. To enhance the anti-interference ability of this system, the sampled signals are amplified and adjusted by the signal disposal instrument. Through the spectrum transformation and spectrum analysis of the sampled noise signals, the noise causes of the power tool rest can be inquired and the concerned measurements can be taken to reduce the noise effectively. Finally, the sampled data is stored by the data saving function.

Computer graphics simulation of a CNC lathe

1985 ◽  
Vol 9 (2) ◽  
pp. 127-134 ◽  
Author(s):  
David V. Hutton ◽  
Ameer Hassan
Keyword(s):  
Computer Graphics ◽  
Cnc Lathe
Sign in / Sign up

Export Citation Format

Share Document