Anomalous iron losses in cold-reduced grain-oriented transformer steel

1964 ◽  
Vol 111 (8) ◽  
pp. 1463 ◽  
Author(s):  
F. Brailsford ◽  
R. Fogg
Keyword(s):  
Transformer Steel ◽  
Iron Losses

FIELD WEAKENING CONTROL FOR INDUCTION MOTORS BASED ON COPPER AND IRON LOSSES MINIMIZATION

2020 ◽  
Vol 3 (2) ◽  
pp. 44-57
Author(s):  
Olga Tolochko ◽  
◽  
Danylo Kaluhin ◽  
Stefan Palis ◽  
Serhii Oshurko ◽  
...  
Keyword(s):  
Induction Motors ◽  
Field Weakening ◽  
Iron Losses

scholarly journals Iron Loss Analysis of a Concentrated Winding Type Interior Permanent Magnet Synchronous Motor with Single and Dual Layer Magnet Shape

Machines ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 74
Author(s):  
Chan-Ho Baek ◽  
Hyo-Seob Shin ◽  
Jang-Young Choi
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnet Synchronous Motor ◽  
Homogenization Method ◽  
Iron Loss ◽  
Frequency Separation ◽  
Permanent Magnet Synchronous Motors ◽  
Loss Analysis ◽  
Iron Losses ◽  
Interior Permanent Magnet ◽  
Rotor Type

In this study, the iron losses of high flux density concentrated winding-type interior permanent magnet synchronous motors for three different magnet shapes (single-V, single-flat, and dual-delta) and rotor structures are analyzed and compared. Iron loss is analyzed using the classical Steinmetz equation (CSE) based on the frequency separation approach using the iron loss material table, and each rotor type is compared. In addition, to validate the hysteresis loss for each rotor type, two additional analyses are performed. In the methods considered, the number of minor loops is counted, and the area is calculated based on DC bias. The eddy current loss is compared using two approaches: CSE base frequency separation and the homogenization method considering the skin effect. This study primarily focuses on the comparison of relative iron losses based on different rotor topologies instead of absolute comparisons.

scholarly journals Verification of electric steel punching simulation results using microhardness

2021 ◽  
Author(s):  
Sampsa Vili Antero Laakso ◽  
Ugur Aydin ◽  
Peter Krajnik
Keyword(s):  
Plastic Deformation ◽  
High Speed ◽  
Steel Sheet ◽  
Electrical Steel ◽  
High Speed Steel ◽  
Experimental Methods ◽  
Fem Simulations ◽  
Iron Losses ◽  
Simulation Results ◽  
Electrical Steel Sheet

AbstractOne of the most dominant manufacturing methods in the production of electromechanical devices from sheet metal is punching. In punching, the material undergoes plastic deformation and finally fracture. Punching of an electrical steel sheet causes plastic deformation on the edges of the part, which affects the magnetic properties of the material, i.e., increases iron losses in the material, which in turn has a negative effect on the performance of the electromagnetic devices in the final product. Therefore, punching-induced iron losses decrease the energy efficiency of the device. FEM simulations of punching have shown significantly increased plastic deformation on the workpiece edges with increasing tool wear. In order to identify the critical tool wear, after which the iron losses have increased beyond acceptable limits, the simulation results must be verified with experimental methods. The acceptable limits are pushed further in the standards by the International Electrotechnical Commission (IEC). The new standard (IEC TS 60034-30-2:2016) has much stricter limits regarding the energy efficiency of electromechanical machines, with an IE5 class efficiency that exceeds the previous IE4 class (IEC 60034-30-1:2014) requirements by 30%. The simulations are done using Scientific Forming Technologies Corporation Deform, a finite element software for material processing simulations. The electrical steel used is M400-50A, and the tool material is Vanadis 23, a powder-based high-speed steel. Vanadis 23 is a high alloyed powder metallurgical high-speed steel with a high abrasive wear resistance and a high compressive strength. It is suitable for cold work processing like punching. In the existing literature, FEM simulations and experimental methods have been incorporated for investigating the edge deformation properties of sheared surfaces, but there is a research gap in verifying the simulation results with the experimental methods. In this paper, FEM simulation of the punching process is verified using an electrical steel sheet from real production environment and measuring the deformation of the edges using microhardness measurements. The simulations show high plastic deformation 50 μm into the workpiece edge, a result that is shown to be in good agreement with the experimental results.

An improved method for predicting iron losses in brushless permanent magnet DC drives

1992 ◽  
Vol 28 (5) ◽  
pp. 2997-2999 ◽  
Author(s):  
K. Atallah ◽  
Z.Q. Zhu ◽  
D. Howe
Keyword(s):  
Permanent Magnet ◽  
Improved Method ◽  
Iron Losses
Sign in / Sign up

Export Citation Format

Share Document