scholarly journals Structural vibration quantification of micro wind turbine-building system using a novel finite element analysis

2016 ◽  
Vol 2016 (8) ◽  
pp. 277-290
Author(s):  
Bo Ren
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Structural Vibration ◽  
Element Analysis ◽  
Building System

Investigation of stiffness of small wind turbine blade based on vibration analysis technique

2019 ◽  
Vol 44 (1) ◽  
pp. 49-59
Author(s):  
Nilesh Chandgude ◽  
Nitin Gadhave ◽  
Ganesh Taware ◽  
Nitin Patil
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Natural Frequency ◽  
Vibration Analysis ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Element Analysis ◽  
Finite Element Software ◽  
Small Wind Turbine

In this article, three small wind turbine blades of different materials were manufactured. Finite element analysis was carried out using finite element software ANSYS 14.5 on modeled blades of National Advisory Committee for Aeronautics 4412 airfoil profile. From finite element analysis, first, two flap-wise natural frequencies and mode shapes of three different blades are obtained. Experimental vibration analysis of manufactured blades was carried out using fast Fourier transform analyzer to find the first two flap-wise natural frequencies. Finally, the results obtained from the finite element analysis and experimental test of three blades are compared. Based on vibration analysis, we found that the natural frequency of glass fiber reinforced plastic blade reinforced with aluminum sheet metal (small) strips increases compared with the remaining blades. An increase in the natural frequency indicates an increase in the stiffness of blade.

Strength Evaluation and Failure Prediction of a Composite Wind Turbine Blade Using Finite Element Analysis

2010 ◽  
Author(s):  
Prenil Poulose ◽  
Zhong Hu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Turbine Blades ◽  
Failure Prediction ◽  
Element Model ◽  
Wind Turbine Blade ◽  
Element Analysis ◽  
Strength Evaluation

Strength evaluation and failure prediction on a modern composite wind turbine blade have been conducted using finite element analysis. A 3-dimensional finite element model has been developed. Stresses and deflections in the blade under extreme storm conditions have been investigated for different materials. The conventional wood design turbine blade has been compared with the advanced E-glass fiber and Carbon epoxy composite blades. Strength has been analyzed and compared for blades with different laminated layer stacking sequences and fiber orientations for a composite material. Safety design and failure prediction have been conducted based on the different failure criteria. The simulation error estimation has been evaluated. Simulation results have shown that finite element analysis is crucial for designing and optimizing composite wind turbine blades.

Wear Performance of Mooring Chain in Wet Environment With Substitute Ocean Water

2019 ◽  
Author(s):  
Koji Gotoh ◽  
Tetsuya Ueda ◽  
Koji Murakami ◽  
Tomoaki Utsunomiya
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Deep Sea ◽  
Green Energy ◽  
Maintenance Cost ◽  
Ocean Water ◽  
Element Analysis ◽  
Wear Performance ◽  
Floating Wind Turbine

Abstract Floating wind turbine facilities installed in deep sea areas play an essential role in the promotion of green energy. One of the problems associated with the commercialization of facilities installed in the deep sea is the maintenance cost of mooring chains, because they are expensive and wear between links leads to chain breakage. Therefore, it is necessary to establish a quantitative wear evaluation method for mooring chains. An experimental facility to reproduce the wear caused by sliding between links at the scale of an actual floating wind turbine was developed to investigate the wear performance in seawater conditions, and wear tests were conducted. Substitute ocean water was applied to the experiment instead of seawater. In addition, a procedure for nonlinear finite element analysis was improved to estimate the behaviour of wear between links. Measured stress versus strain relations of the links was considered in the finite element analysis. The experiments and numerical analysis confirmed that the amount of wear in the substitute ocean water was less than that obtained in dry air and that the tensile force between links is an important factor for the degree of wear between links.

Finite Element Analysis and Vibration Suppression Control of Smart Wind Turbine Blade

2011 ◽  
Vol 19 (3-4) ◽  
pp. 747-754 ◽  
Author(s):  
Yin-hu Qiao ◽  
Jiang Han ◽  
Chun-yan Zhang ◽  
Jie-ping Chen ◽  
Ke-chuan Yi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Vibration Suppression ◽  
Wind Turbine Blade ◽  
Element Analysis

Chosen of Strength Criterion for Different Region of Blade

2012 ◽  
Vol 608-609 ◽  
pp. 755-758
Author(s):  
De Tian ◽  
Qi Li ◽  
Jian Mei Zhang ◽  
Xiao Dong Zhang ◽  
Ning Bo Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Strength Criterion ◽  
Fatigue Index ◽  
Element Analysis ◽  
Strength Criteria ◽  
Security And Reliability ◽  
Blade Model ◽  
Dangerous Section

Use software Pro/E to build a blade model based on 1.5MW wind turbine, analyze stress characteristics of different regions including spar cap, webs and trailing edge of the dangerous section of blade at related loads by using different strength criteria to make finite element analysis to check the strength, through comparing the F.I.(fatigue index) and stress bringing about the idea that using different strength criteria to analyze different material of different regions can ensure the security and reliability of the designed blade at large extent.

Finite Element Analysis of Top Flanged Joint System of High Power Level Wind Turbine

2012 ◽  
Vol 591-593 ◽  
pp. 728-732
Author(s):  
Rong Zhang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Rational Design ◽  
Large Scale ◽  
Power Level ◽  
Operating Mode ◽  
Element Model ◽  
Element Analysis ◽  
Joint System

This paper uses non-linear finite element method to structurally analyze top flanged joint system of a MW wind turbine, sets up a finite element model of top flanged joint system by applying finite element analysis software MSC.Marc/Mentat, makes an analysis on the stress distribution of key components of top flanged joint system under ultimate operating mode based on applying appropriate boundary condition and loads, and carries out security examination on top flange and joint bolt. Result shows that key components of the top flanged joint system can satisfy design requirements, and it has a guiding role for rational design and performance improvement of large scale wind turbine flange, which can be used in structural analysis of other flanged joint systems, and has certain practical value in the aspect of engineering.

Sign in / Sign up

Export Citation Format

Share Document