Metal parts additively manufactured Laser based AM systems Why ?, Where

2015 ◽  
Author(s):  
S. Crownshaw
Keyword(s):  
Metal Parts

Transmission Electron Microscopy of an Aluminum-Silver-Stainless Steel Solid State Bond

1985 ◽  
Vol 43 ◽  
pp. 172-173
Author(s):  
M. J. Carr ◽  
J. F. Shewbridge ◽  
T. O. Wilford
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Solid State ◽  
Specimen Preparation ◽  
Dimensional Control ◽  
Tem Analysis ◽  
Metal Parts ◽  
Dissimilar Metal ◽  
Transmission Electron ◽  
Short Time

Strong solid state bonds are routinely produced between physical vapor deposited (PVD) silver coatings deposited on sputter cleaned surfaces of two dissimilar metal parts. The low temperature (200°C) and short time (10 min) used in the bonding cycle are advantageous from the standpoint of productivity and dimensional control. These conditions unfortunately produce no microstructural changes at or near the interface that are detectable by optical, SEM, or microprobe examination. Microstructural problems arising at these interfaces could therefore easily go undetected by these techniques. TEM analysis has not been previously applied to this problem because of the difficulty in specimen preparation. The purpose of this paper is to describe our technique for preparing specimens from solid state bonds and to present our initial observations of the microstructural details of such bonds.

Experimental and Numerical Analysis of Blanking for Thin Sheet Metal Parts

2001 ◽  
Vol 4 (3-4) ◽  
pp. 319-333
Author(s):  
Vincent Lemiale ◽  
Philippe Picart ◽  
Sébastien Meunier
Keyword(s):  
Numerical Analysis ◽  
Sheet Metal ◽  
Thin Sheet ◽  
Metal Parts ◽  
Sheet Metal Parts ◽  
Thin Sheet Metal

scholarly journals A study on casting of structural mesh-like metal parts

2021 ◽  
Vol 1037 (1) ◽  
pp. 012017
Author(s):  
D Vlagkoulis ◽  
A Vasileiou ◽  
G-C Vosniakos
Keyword(s):  
Metal Parts

Micro dents fabrication by laser shock peening on surfaces of metal parts

2021 ◽  
Author(s):  
D. S. Shtereveria ◽  
A. A. Volkova ◽  
A. A. Kholopov ◽  
M. A. Melnikova ◽  
D. M. Melnikov
Keyword(s):  
Laser Shock Peening ◽  
Laser Shock ◽  
Metal Parts ◽  
Shock Peening

scholarly journals Analysis of Proximity Consequences of Coil Windings in Electromagnetic Forming

2021 ◽  
Vol 5 (2) ◽  
pp. 45
Author(s):  
Siddhant Prakash Goyal ◽  
Mohammadjavad Lashkari ◽  
Awab Elsayed ◽  
Marlon Hahn ◽  
A. Erman Tekkaya
Keyword(s):  
Proximity Effect ◽  
Experimental Methods ◽  
Electromagnetic Forming ◽  
Velocity Measurements ◽  
Local Curvature ◽  
Metal Parts ◽  
Sheet Metal Parts ◽  
Geometrical Features ◽  
Physical Phenomena ◽  
Inverse Distance

Multiturn coils are required for manufacturing sheet metal parts with varying depths and special geometrical features using electromagnetic forming (EMF). Due to close coil turns, the physical phenomena of the proximity effect and Lorentz forces between the parallel coil windings are observed. This work attempts to investigate the mechanical consequences of these phenomena using numerical and experimental methods. A numerical model was developed in LS-DYNA. It was validated using experimental post-mortem strain and laser-based velocity measurements after and during the experiments, respectively. It was observed that the proximity effect in the parallel conductors led to current density localization at the closest or furthest ends of the conductor cross-section and high local curvature of the formed sheet. Further analysis of the forces between two coil windings explained the departure from the “inverse-distance” rule observed in the literature. Finally, some measures to prevent or reduce undesired coil deformation are provided.

Sign in / Sign up

Export Citation Format

Share Document