High temperature CW operation of 1.5 μm InGaAsP/InP buffer-layer loaded planoconvex waveguide lasers

1981 ◽  
Vol 17 (6) ◽  
pp. 226 ◽  
Author(s):  
Y. Noda ◽  
K. Sakai ◽  
Y. Matsushima
Keyword(s):  
High Temperature ◽  
Buffer Layer ◽  
Waveguide Lasers ◽  
Cw Operation

scholarly journals Investigation of the Heteroepitaxial Process Optimization of Ge Layers on Si (001) by RPCVD

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 928
Author(s):  
Yong Du ◽  
Zhenzhen Kong ◽  
Muhammet Toprak ◽  
Guilei Wang ◽  
Yuanhao Miao ◽  
...  
Keyword(s):  
High Temperature ◽  
Buffer Layer ◽  
Layer Thickness ◽  
Growth Temperature ◽  
Crystalline Quality ◽  
Initial Growth ◽  
Two Dimensional ◽  
High Quality ◽  
Reduced Pressure

This work presents the growth of high-quality Ge epilayers on Si (001) substrates using a reduced pressure chemical vapor deposition (RPCVD) chamber. Based on the initial nucleation, a low temperature high temperature (LT-HT) two-step approach, we systematically investigate the nucleation time and surface topography, influence of a LT-Ge buffer layer thickness, a HT-Ge growth temperature, layer thickness, and high temperature thermal treatment on the morphological and crystalline quality of the Ge epilayers. It is also a unique study in the initial growth of Ge epitaxy; the start point of the experiments includes Stranski–Krastanov mode in which the Ge wet layer is initially formed and later the growth is developed to form nuclides. Afterwards, a two-dimensional Ge layer is formed from the coalescing of the nuclides. The evolution of the strain from the beginning stage of the growth up to the full Ge layer has been investigated. Material characterization results show that Ge epilayer with 400 nm LT-Ge buffer layer features at least the root mean square (RMS) value and it’s threading dislocation density (TDD) decreases by a factor of 2. In view of the 400 nm LT-Ge buffer layer, the 1000 nm Ge epilayer with HT-Ge growth temperature of 650 °C showed the best material quality, which is conducive to the merging of the crystals into a connected structure eventually forming a continuous and two-dimensional film. After increasing the thickness of Ge layer from 900 nm to 2000 nm, Ge surface roughness decreased first and then increased slowly (the RMS value for 1400 nm Ge layer was 0.81 nm). Finally, a high-temperature annealing process was carried out and high-quality Ge layer was obtained (TDD=2.78 × 107 cm−2). In addition, room temperature strong photoluminescence (PL) peak intensity and narrow full width at half maximum (11 meV) spectra further confirm the high crystalline quality of the Ge layer manufactured by this optimized process. This work highlights the inducing, increasing, and relaxing of the strain in the Ge buffer and the signature of the defect formation.

scholarly journals Critical View on Buffer Layer Formation and Monolayer Graphene Properties in High-Temperature Sublimation

2021 ◽  
Vol 11 (4) ◽  
pp. 1891
Author(s):  
Vallery Stanishev ◽  
Nerijus Armakavicius ◽  
Chamseddine Bouhafs ◽  
Camilla Coletti ◽  
Philipp Kühne ◽  
...  
Keyword(s):  
High Temperature ◽  
Charge Carrier ◽  
Buffer Layer ◽  
Free Charge Carrier ◽  
Monolayer Graphene ◽  
Free Charge ◽  
Layer Formation ◽  
Free Hole ◽  
Sublimation Growth ◽  
Insulating Substrates

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using closed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer graphene on 4H–SiC. We show that by introducing Ar at higher temperatures, TAr, one can shift the formation of the buffer layer to higher temperatures for both n-type and semi-insulating substrates. A scenario explaining the observed suppressed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface is suggested to take place for intrinsic monolayer graphene grown at 2000 ∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

Growth and characterization of GaN films on Si(111) substrate using high-temperature AlN buffer layer

2005 ◽  
Vol 198 (1-3) ◽  
pp. 350-353 ◽  
Author(s):  
Xianfeng Ni ◽  
Liping Zhu ◽  
Zhizhen Ye ◽  
Zhe Zhao ◽  
Haiping Tang ◽  
...  
Keyword(s):  
High Temperature ◽  
Buffer Layer ◽  
Aln Buffer

The Influence of Growth Temperature on Oxygen Concentration in GaN Buffer Layer

2008 ◽  
Vol 1068 ◽  
Author(s):  
Ewa Dumiszewska ◽  
Wlodek Strupinski ◽  
Piotr Caban ◽  
Marek Wesolowski ◽  
Dariusz Lenkiewicz ◽  
...  
Keyword(s):  
High Temperature ◽  
Buffer Layer ◽  
Oxygen Concentration ◽  
Growth Temperature ◽  
Low Temperatures ◽  
Buffer Layers ◽  
Crystalline Quality ◽  
Temperature Growth ◽  
Gan Buffer Layer

ABSTRACTThe influence of growth temperature on oxygen incorporation into GaN epitaxial layers was studied. GaN layers deposited at low temperatures were characterized by much higher oxygen concentration than those deposited at high temperature typically used for epitaxial growth. GaN buffer layers (HT GaN) about 1 μm thick were deposited on GaN nucleation layers (NL) with various thicknesses. The influence of NL thickness on crystalline quality and oxygen concentration of HT GaN layers were studied using RBS and SIMS. With increasing thickness of NL the crystalline quality of GaN buffer layers deteriorates and the oxygen concentration increases. It was observed that oxygen atoms incorporated at low temperature in NL diffuse into GaN buffer layer during high temperature growth as a consequence GaN NL is the source for unintentional oxygen doping.

scholarly journals The Progress on Low-Cost, High-Quality, High-Temperature Superconducting Tapes Deposited by the Combustion Chemical Vapor Deposition Process

2001 ◽  
Vol 689 ◽  
Author(s):  
Shara S. Shoup ◽  
Marvis K. White ◽  
Steve L. Krebs ◽  
Natalie Darnell ◽  
Adam C. King ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
High Temperature ◽  
Critical Current Density ◽  
Buffer Layer ◽  
Critical Current ◽  
Vapor Deposition ◽  
Low Cost ◽  
Chemical Vapor ◽  
High Critical Current Density ◽  
High Quality

ABSTRACTThe innovative Combustion Chemical Vapor Deposition (CCVD) process is a non-vacuum technique that is being investigated to enable next generation products in several application areas including high-temperature superconductors (HTS). In combination with the Rolling Assisted Biaxially Textured Substrate (RABiTS) technology, the CCVD process has significant promise to provide low-cost, high-quality lengths of YBCO coated conductor. The CCVD technology has been used to deposit both buffer layer coatings as well as YBCO superconducting layers. A buffer layer architecture of strontium titanate and ceria have been deposited by CCVD on textured nickel substrates and optimized to appropriate thicknesses and microstructures to provide templates for growing PLD YBCO with high critical current density values. The CCVD buffer layers have been scaled to meter plus lengths with good epitaxial uniformity along the length. A short sample cut from one of the lengths enabled high critical current density PLD YBCO. Films of CCVD YBCO superconductors have been grown on single crystal substrates with critical current densities over 1 MA/cm2. Work is currently in progress to combine both the buffer layer and superconductor technologies to produce high-quality coupons of HTS tape made entirely by the non-vacuum CCVD process.

Sign in / Sign up

Export Citation Format

Share Document