Optimal placement of capacitors for loss reduction in deregulated distribution system

2006 ◽  
Author(s):  
B.V. Vibhute ◽  
H.P. Inamdar ◽  
R.C. Balapure
Keyword(s):  
Distribution System ◽  
Optimal Placement ◽  
Loss Reduction

Application of Tabu Search for Optimal Placement and Sizing of Distributed Generation for Loss Reduction

2012 ◽  
Vol 433-440 ◽  
pp. 7190-7194 ◽  
Author(s):  
Nattachote Rugthaicharoencheep ◽  
Thong Lantharthong ◽  
Awiruth Ratreepruk ◽  
Jenwit Ratchatha
Keyword(s):  
Tabu Search ◽  
Distributed Generation ◽  
Distribution System ◽  
Power Loss ◽  
Power Flow ◽  
Search Algorithm ◽  
Optimal Placement ◽  
Loss Reduction ◽  
Placement Problem ◽  
Bus Voltage

This paper presents the optimal and sizing of distributed generation (DG) placement in a radial distribution system for loss reduction. The main emphasis of this paper is to identify proper locations for installing DGs in a distribution system to reduce active power loss and improve bus voltages. Nevertheless, proper placement and sizing of DG units are not straightforward to be identified as a number of their positions and capacities need to be determined. It is therefore proposed in this paper to solve a DG placement problem based on a Tabu search algorithm. The objective function of the problem is to minimize the system loss subject to power flow constraints, bus voltage limits, pre specified number of DGs, and their allowable total installed capacity, and only one distributed generator for one installation position. The effectiveness of the methodology is demonstrated by a practical sized distribution system consisting of 69 bus and 48 load points. The results show that the optimal DG placement and sizing can be identified to give the minimum power loss while respecting all the constraints.

scholarly journals Optimal Placement of Distribution Generation to Minimize Losses using Backward Forward Sweep Method in Distribution System

2019 ◽  
Vol 8 (6S3) ◽  
pp. 806-810
Keyword(s):  
Distribution System ◽  
Distribution Systems ◽  
Optimal Placement ◽  
Loss Reduction ◽  
Sweep Method ◽  
Utility System ◽  
Distribution Generation ◽  
Optimal Site ◽  
Bus System

Nowadays, there is a large interest in the penetration of Distribution Generation Units in the Utility System. This penetration of Distribution Generation requires proper planning for the system while considering DG impact on the Distribution System. It requires attention towards DG location which place in the system and size of DG units. The proper location of DG should also be considered to reduce losses in the utility System. This Paper Proposes finding optimal site and size of DG in Distribution Systems and it is tested in IEEE 33 bus system. The loss reduction after placing DG is shown in the results.

scholarly journals Leveraging a Genetic Algorithm for the Optimal Placement of Distributed Generation and the Need for Energy Management Strategies Using a Fuzzy Inference System

Electronics ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 172
Author(s):  
Sunny Katyara ◽  
Muhammad Fawad Shaikh ◽  
Shoaib Shaikh ◽  
Zahid Hussain Khand ◽  
Lukasz Staszewski ◽  
...  
Keyword(s):  
Genetic Algorithm ◽  
Energy Management ◽  
Fuzzy Inference System ◽  
Distribution System ◽  
Fuzzy Inference ◽  
Management Strategies ◽  
Test System ◽  
Optimal Placement ◽  
Inference System ◽  
Simulated Environment

With the rising load demand and power losses, the equipment in the utility network often operates close to its marginal limits, creating a dire need for the installation of new Distributed Generators (DGs). Their proper placement is one of the prerequisites for fully achieving the benefits; otherwise, this may result in the worsening of their performance. This could even lead to further deterioration if an effective Energy Management System (EMS) is not installed. Firstly, addressing these issues, this research exploits a Genetic Algorithm (GA) for the proper placement of new DGs in a distribution system. This approach is based on the system losses, voltage profiles, and phase angle jump variations. Secondly, the energy management models are designed using a fuzzy inference system. The models are then analyzed under heavy loading and fault conditions. This research is conducted on a six bus radial test system in a simulated environment together with a real-time Power Hardware-In-the-Loop (PHIL) setup. It is concluded that the optimal placement of a 3.33 MVA synchronous DG is near the load center, and the robustness of the proposed EMS is proven by mitigating the distinct contingencies within the approximately 2.5 cycles of the operating period.

Sign in / Sign up

Export Citation Format

Share Document