Electrical machine failures, causes and cures

1997 ◽  
Author(s):  
M.M. Botha
Keyword(s):  
Electrical Machine

New Holtz Electrical Machine

1877 ◽  
Vol 3 (70supp) ◽  
pp. 1108-1108
Author(s):  
Elihu Thomson
Keyword(s):  
Electrical Machine

scholarly journals Impact of residual stress evoked by pyramidal embossing on the magnetic material properties of non-oriented electrical steel

2021 ◽  
Author(s):  
Ines Gilch ◽  
Tobias Neuwirth ◽  
Benedikt Schauerte ◽  
Nora Leuning ◽  
Simon Sebold ◽  
...  
Keyword(s):  
Magnetic Material ◽  
Residual Stress ◽  
Magnetic Flux ◽  
Material Properties ◽  
Electrical Steel ◽  
Maximum Energy ◽  
Material Behavior ◽  
Electrical Machine ◽  
Element Analysis ◽  
Steel Sheets

AbstractTargeted magnetic flux guidance in the rotor cross section of rotational electrical machines is crucial for the machine’s efficiency. Cutouts in the electrical steel sheets are integrated in the rotor sheets for magnetic flux guidance. These cutouts create thin structures in the rotor sheets which limit the maximum achievable rotational speed under centrifugal forces and the maximum energy density of the rotating electrical machine. In this paper, embossing-induced residual stress, employing the magneto-mechanical Villari effect, is studied as an innovative and alternative flux barrier design with negligible mechanical material deterioration. The overall objective is to replace cutouts by embossings, increasing the mechanical strength of the rotor. The identification of suitable embossing geometries, distributions and methodologies for the local introduction of residual stress is a major challenge. This paper examines finely distributed pyramidal embossings and their effect on the magnetic material behavior. The study is based on simulation and measurements of specimen with a single line of twenty embossing points performed with different punch forces. The magnetic material behavior is analyzed using neutron grating interferometry and a single sheet tester. Numerical examinations using finite element analysis and microhardness measurements provide a more detailed understanding of the interaction of residual stress distribution and magnetic material properties. The results reveal that residual stress induced by embossing affects magnetic material properties. Process parameters can be applied to adjust the magnetic material deterioration and the effect of magnetic flux guidance.

scholarly journals Reliability-Oriented Design of Inverter-Fed Low-Voltage Electrical Machines: Potential Solutions

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4144
Author(s):  
Yatai Ji ◽  
Paolo Giangrande ◽  
Vincenzo Madonna ◽  
Weiduo Zhao ◽  
Michael Galea
Keyword(s):  
Power Density ◽  
High Speed ◽  
High Performance ◽  
Low Voltage ◽  
Electrical Machines ◽  
Design Stage ◽  
Switching Frequency ◽  
Special Focus ◽  
Electrical Machine ◽  
Engineering Approach

Transportation electrification has kept pushing low-voltage inverter-fed electrical machines to reach a higher power density while guaranteeing appropriate reliability levels. Methods commonly adopted to boost power density (i.e., higher current density, faster switching frequency for high speed, and higher DC link voltage) will unavoidably increase the stress to the insulation system which leads to a decrease in reliability. Thus, a trade-off is required between power density and reliability during the machine design. Currently, it is a challenging task to evaluate reliability during the design stage and the over-engineering approach is applied. To solve this problem, physics of failure (POF) is introduced and its feasibility for electrical machine (EM) design is discussed through reviewing past work on insulation investigation. Then the special focus is given to partial discharge (PD) whose occurrence means the end-of-life of low-voltage EMs. The PD-free design methodology based on understanding the physics of PD is presented to substitute the over-engineering approach. Finally, a comprehensive reliability-oriented design (ROD) approach adopting POF and PD-free design strategy is given as a potential solution for reliable and high-performance inverter-fed low-voltage EM design.

Sign in / Sign up

Export Citation Format

Share Document