Design and evaluation of a new type of protection for wind farms

1997 ◽  
Author(s):  
S.J. Haslam
Keyword(s):  
Wind Farms ◽  
New Type

Jet Streams as Power Generating Electrical Energy in Libya

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
Abdelfatah H Shibani
Keyword(s):  
Wind Turbines ◽  
Wind Farms ◽  
Electrical Energy ◽  
Clean Energy ◽  
Economic Feasibility ◽  
Jet Streams ◽  
Energy Investment ◽  
Regular Source ◽  
New Type ◽  
New Generation

The supreme wind sources are extremely huge, and according to estimations, these winds can supply Libya with great quantity of electrical energy. Among the examples of contemporary engineering technologies in this field, is to create a new generation of Airborne Wind Turbines. Scientists realized that winds near the Earth’s surface are too weak to provide a regular source of energy due to the presence of aerobic swirls and obstacles, which represent a source of ground friction being the cause of weakening wind power. Some consider that the Earth’s surface is a totally inappropriate place for investing wind energy. As an alternative solution, we start to think about the establishment of wind farms in another place away from the Earth’s surface by developing a new type that can run within the upper-air layers, precisely at jet streams areas. In comparison with fluctuating winds blowing gently near the Earth’s surface, scientists estimate that the energy of jet streams increases a thousand times than that can be gathered from the most powerful winds on high hills. To be able to provide a clear picture of the possibility of energy investment of jet streams, we shall present, across the pages of this paper, an explanation of the topic through the following aspects: How do Airborne Wind Turbines’ trip start, their advantages and difficulties faced, benefits and economic feasibility, General Atmospheric Circulation and jet streams. Since Libya is among the fortunate countries in the world, through which subtropical jet streams pass, we made an analysis and follow-up of daily synoptic charts, which show jet winds’ speed, direction and their altitudes for a period of 60 consecutive months starting from January 1, 2003 until December 31, 2007. Also, an analysis was made of daily observational data of jet winds recorded by Tripoli Upper-air Station during the period from the beginning of March 1987 until the end of February 1989. The paper’s results summarized that jet streams will be in the future one of the important clean energy strategic sources, and can provide a capacity, whose expected intensity is up to 19 kilowatts per square meter. It recommends giving attention to jet streams at the research, experimental and technological levels because research, experimental and technological proficiencies can provide more exciting solutions for energy problems in Libya.

Evaluation of a new type of protection relay for wind farms

1998 ◽  
Author(s):  
P. Crossley ◽  
S. Haslam ◽  
N. Jenkins
Keyword(s):  
Wind Farms ◽  
Protection Relay ◽  
New Type

The Microstructure of Shock-Synthesized Diamond

1967 ◽  
Vol 25 ◽  
pp. 324-325
Author(s):  
Lucien F. Trueb
Keyword(s):  
Single Crystals ◽  
Preferred Orientation ◽  
High Magnification ◽  
Texture Pattern ◽  
Shock Process ◽  
New Type ◽  
Diffraction Diagram

A new type of synthetic industrial diamond formed by an explosive shock process has been recently developed by the Du Pont Company. This material consists of a mixture of two basically different forms, as shown in Figure 1: relatively flat and compact aggregates of acicular crystallites, and single crystals in the form of irregular polyhedra with straight edges.Figure 2 is a high magnification micrograph typical for the fibrous aggregates; it shows that they are composed of bundles of crystallites 0.05-0.3 μ long and 0.02 μ. wide. The selected area diffraction diagram (insert in Figure 2) consists of a weak polycrystalline ring pattern and a strong texture pattern with arc reflections. The latter results from crystals having preferred orientation, which shows that in a given particle most fibrils have a similar orientation.

New type electron gun with electrostatic and electromagnetic lenses

1978 ◽  
Vol 36 (1) ◽  
pp. 62-63
Author(s):  
T. Ichinokawa ◽  
H. Maeda
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Optimum Condition ◽  
Bias Voltage ◽  
Electron Gun ◽  
Charge Effect ◽  
Micro Fabrication ◽  
Maximum Brightness ◽  
New Type ◽  
The Ideal

I. IntroductionThermionic electron gun with the Wehnelt grid is popularly used in the electron microscopy and electron beam micro-fabrication. It is well known that this gun could get the ideal brightness caluculated from the Lengumier and Richardson equations under the optimum condition. However, the design and ajustment to the optimum condition is not so easy. The gun has following properties with respect to the Wehnelt bias; (1) The maximum brightness is got only in the optimum bias. (2) In the larger bias than the optimum, the brightness decreases with increasing the bias voltage on account of the space charge effect. (3) In the smaller bias than the optimum, the brightness decreases with bias voltage on account of spreading of the cross over spot due to the aberrations of the electrostatic immersion lens.In the present experiment, a new type electron gun with the electrostatic and electromagnetic lens is designed, and its properties are examined experimentally.

A new type of defect structure in 124-superconducting oxide revealed by HREM

1991 ◽  
Vol 49 ◽  
pp. 1092-1093
Author(s):  
R. Sharma ◽  
B.L. Ramakrishna ◽  
N.N. Thadhani ◽  
D. Hianes ◽  
Z. Iqbal
Keyword(s):  
Shock Wave ◽  
Defect Structure ◽  
Neutron Radiation ◽  
Weak Links ◽  
Defect Structures ◽  
New Materials ◽  
New Type ◽  
Current Densities ◽  
Processing Techniques ◽  
Microstructural Studies

After materials with superconducting temperatures higher than liquid nitrogen have been prepared, more emphasis has been on increasing the current densities (Jc) of high Tc superconductors than finding new materials with higher transition temperatures. Different processing techniques i.e thin films, shock wave processing, neutron radiation etc. have been applied in order to increase Jc. Microstructural studies of compounds thus prepared have shown either a decrease in gram boundaries that act as weak-links or increase in defect structure that act as flux-pinning centers. We have studied shock wave synthesized Tl-Ba-Cu-O and shock wave processed Y-123 superconductors with somewhat different properties compared to those prepared by solid-state reaction. Here we report the defect structures observed in the shock-processed Y-124 superconductors.

ESEM - A multipurpose surface Electron Microscope

1986 ◽  
Vol 44 ◽  
pp. 632-633 ◽  
Author(s):  
G.D. Danilatos
Keyword(s):  
Electron Microscope ◽  
Room Temperature ◽  
Environmental Scanning ◽  
Gas Composition ◽  
Saturated Water Vapor ◽  
Surface Electron ◽  
Current State ◽  
Saturated Water ◽  
New Type ◽  
Temperature And Pressure

Over recent years a new type of electron microscope - the environmental scanning electron microscope (ESEM) - has been developed for the examination of specimen surfaces in the presence of gases. A detailed series of reports on the system has appeared elsewhere. A review summary of the current state and potential of the system is presented here.The gas composition, temperature and pressure can be varied in the specimen chamber of the ESEM. With air, the pressure can be up to one atmosphere (about 1000 mbar). Environments with fully saturated water vapor only at room temperature (20-30 mbar) can be easily maintained whilst liquid water or other solutions, together with uncoated specimens, can be imaged routinely during various applications.

Trial production of γ-type energy filtering TEM

1995 ◽  
Vol 53 ◽  
pp. 604-605
Author(s):  
Y. Taniguchi ◽  
E. Nakazawa ◽  
S. Taya
Keyword(s):  
Magnetic Energy ◽  
Electron Optics ◽  
Electron Microscopic ◽  
Mass Spectrometers ◽  
Ion Optics ◽  
Energy Filtering ◽  
New Information ◽  
New Type ◽  
Fringing Fields

Imaging energy filters can add new information to electron microscopic images with respect to energy-axis, so-called electron spectroscopic imaging (ESI). Recently, many good results have been reported using this imaging technique. ESI also allows high-contrast observation of unstained biological samples, becoming a trend of the field of morphology. We manufactured a new type of energy filter as a trial production. This energy filter consists of two magnets, and we call γ-filter since the trajectory of electrons shows ‘γ’-shape inside the filter. We evaluated the new energyγ-filter TEM with the γ-filter.Figure 1 shows schematic view of the electron optics of the γ-type energy filter. For the determination of the electron-optics of the γ-type energy filter, we used the TRIO (Third Order Ion Optics) program which has been developed for the design of high resolution mass spectrometers. The TRIO takes the extended fringing fields (EFF) into consideration. EFF makes it difficult to design magnetic energy filters with magnetic sector fields.

Development of imaging plate for a TEM and its characteristics

1989 ◽  
Vol 47 ◽  
pp. 100-101
Author(s):  
N. Mori ◽  
T. Oikawa ◽  
Y. Harada ◽  
J. Miyahara ◽  
T. Matsuo
Keyword(s):  
Dynamic Range ◽  
Protective Layer ◽  
High Sensitivity ◽  
Imaging Plate ◽  
Phosphor Layer ◽  
Imaging Device ◽  
X Ray Imaging ◽  
New Type ◽  
Basic Characteristics ◽  
Reading System

The Imaging Plate (IP) is a new type imaging device, which was developed for diagnostic x ray imaging. We have reported that usage of the IP for a TEM has many merits; those are high sensitivity, wide dynamic range, and good linearity. However in the previous report the reading system was prototype drum-type-scanner, and IP was also experimentally made, which phosphor layer was 50μm thick with no protective layer. So special care was needed to handle them, and they were used only to make sure the basic characteristics. In this article we report the result of newly developed reading, printing system and high resolution IP for practical use. We mainly discuss the characteristics of the IP here. (Precise performance concerned with the reader and other system are reported in the other article.)Fig.1 shows the schematic cross section of the IP. The IP consists of three parts; protective layer, phosphor layer and support.

Automatic analysis of Kikuchi diffraction patterns

1994 ◽  
Vol 52 ◽  
pp. 900-901
Author(s):  
H. Weiland ◽  
D. P. Field
Keyword(s):  
Electron Beam ◽  
Electron Microscope ◽  
Spatial Resolution ◽  
Relevant Information ◽  
Crystalline Materials ◽  
Large Size ◽  
Transmission Electron ◽  
New Type ◽  
Diffraction Patterns ◽  
Orientation Determination

Recent advances in the automatic indexing of backscatter Kikuchi diffraction patterns on the scanning electron microscope (SEM) has resulted in the development of a new type of microscopy. The ability to obtain statistically relevant information on the spatial distribution of crystallite orientations is giving rise to new insight into polycrystalline microstructures and their relation to materials properties. A limitation of the technique in the SEM is that the spatial resolution of the measurement is restricted by the relatively large size of the electron beam in relation to various microstructural features. Typically the spatial resolution in the SEM is limited to about half a micron or greater. Heavily worked structures exhibit microstructural features much finer than this and require resolution on the order of nanometers for accurate characterization. Transmission electron microscope (TEM) techniques offer sufficient resolution to investigate heavily worked crystalline materials.Crystal lattice orientation determination from Kikuchi diffraction patterns in the TEM (Figure 1) requires knowledge of the relative positions of at least three non-parallel Kikuchi line pairs in relation to the crystallite and the electron beam.

New Type of Chromatographic Column

1951 ◽  
Vol 23 (3) ◽  
pp. 428-427 ◽  
Author(s):  
J. M. Miller ◽  
J. G. Kirchner
Keyword(s):  
Chromatographic Column ◽  
New Type
Sign in / Sign up

Export Citation Format

Share Document