Wideband High-Gain Circularly-Polarised Antenna based on Fabry-Perot Concept and a Conical Horn

2018 ◽  
Author(s):  
Yuehe Ge ◽  
Kaiyuan Qin
Keyword(s):  
High Gain ◽  
Fabry Perot ◽  
Conical Horn

scholarly journals A 300-GHz low-cost high-gain fully metallic Fabry–Perot cavity antenna for 6G terahertz wireless communications

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Basem Aqlan ◽  
Mohamed Himdi ◽  
Hamsakutty Vettikalladi ◽  
Laurent Le-Coq
Keyword(s):  
Communication Systems ◽  
Low Cost ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Wireless Communication Systems ◽  
Beam Radiation ◽  
Compact Size ◽  
Fabry Perot ◽  
Operating Bandwidth ◽  
Polarization Level

AbstractA low-cost, compact, and high gain Fabry–Perot cavity (FPC) antenna which operates at 300 GHz is presented. The antenna is fabricated using laser-cutting brass technology. The proposed antenna consists of seven metallic layers; a ground layer, an integrated stepped horn element (three-layers), a coupling layer, a cavity layer, and an aperture-frequency selective surface (FSS) layer. The proposed aperture-FSS function acts as a partially reflective surface, contributing to a directive beam radiation. For verification, the proposed sub-terahertz (THz) FPC antenna prototype was developed, fabricated, and measured. The proposed antenna has a measured reflection coefficient below − 10 dB from 282 to 304 GHz with a bandwidth of 22 GHz. The maximum measured gain observed is 17.7 dBi at 289 GHz, and the gain is higher than 14.4 dBi from 285 to 310 GHz. The measured radiation pattern shows a highly directive pattern with a cross-polarization level below − 25 dB over the whole band in all cut planes, which confirms with the simulation results. The proposed antenna has a compact size, low fabrication cost, high gain, and wide operating bandwidth. The total height of the antenna is 1.24 $${\lambda }_{0}$$ λ 0 ($${\lambda }_{0}$$ λ 0 at the design frequency, 300 GHz) , with a size of 2.6 mm × 2.6 mm. The proposed sub-THz waveguide-fed FPC antenna is suitable for 6G wireless communication systems.

Design and fabrication of a high gain, low cost, LHCP Fabry‐Perot antenna at Ku band

2018 ◽  
Vol 61 (1) ◽  
pp. 101-106 ◽  
Author(s):  
Yousef Azizi ◽  
Nader Komjani ◽  
Majid Karimipour
Keyword(s):  
Low Cost ◽  
High Gain ◽  
Fabry Perot ◽  
Ku Band

scholarly journals Millimeter Wave Fabry-Perot Resonator Antenna Fed by CPW with High Gain and Broadband

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Xue-Xia Yang ◽  
Guan-Nan Tan ◽  
Bing Han ◽  
Hai-Gao Xue
Keyword(s):  
Millimeter Wave ◽  
Coplanar Waveguide ◽  
Dielectric Substrate ◽  
High Gain ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Gain Bandwidth ◽  
Broad Bandwidth ◽  
Low Profile ◽  
Fabry Perot

A novel millimeter wave coplanar waveguide (CPW) fed Fabry-Perot (F-P) antenna with high gain, broad bandwidth, and low profile is reported. The partially reflective surface (PRS) and the ground form the F-P resonator cavity, which is filled with the same dielectric substrate. A dual rhombic slot loop on the ground acts as the primary feeding antenna, which is fed by the CPW and has broad bandwidth. In order to improve the antenna gain, metal vias are inserted surrounding the F-P cavity. A CPW-to-microstrip transition is designed to measure the performances of the antenna and extend the applications. The measured impedance bandwidth ofS11less than −10 dB is from 34 to 37.7 GHz (10.5%), and the gain is 15.4 dBi at the center frequency of 35 GHz with a 3 dB gain bandwidth of 7.1%. This performance of the antenna shows a tradeoff among gain, bandwidth, and profile.

A High-Gain Dielectric Resonator Antenna With Plastic-Based Conical Horn for Millimeter-Wave Applications

2020 ◽  
Vol 19 (6) ◽  
pp. 949-953
Author(s):  
Edoardo Baldazzi ◽  
Ali Al-Rawi ◽  
Renato Cicchetti ◽  
Adrianus Bart Smolders ◽  
Orlandino Testa ◽  
...  
Keyword(s):  
Millimeter Wave ◽  
Dielectric Resonator ◽  
High Gain ◽  
Dielectric Resonator Antenna ◽  
Conical Horn

Realization of Low Scattering for a High-Gain Fabry–Perot Antenna Using Coding Metasurface

2017 ◽  
Vol 65 (7) ◽  
pp. 3374-3383 ◽  
Author(s):  
Lei Zhang ◽  
Xiang Wan ◽  
Shuo Liu ◽  
Jia Yuan Yin ◽  
Qian Zhang ◽  
...  
Keyword(s):  
High Gain ◽  
Fabry Perot

scholarly journals Design of a Substrate-Integrated Fabry-Pérot Cavity Antenna forK-Band Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Truong Khang Nguyen ◽  
Ikmo Park
Keyword(s):  
Coplanar Waveguide ◽  
Ground Plane ◽  
Cost Effective ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Hole Array ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
Fabry Perot ◽  
Feeding Structure

This paper presents the design of a planar, low-profile, high-gain, substrate-integrated Fabry-Pérot cavity antenna forK-band applications. The antenna consists of a frequency selective surface (FSS) and a planar feeding structure, which are both lithographically patterned on a high-permittivity substrate. The FSS is made of a circular hole array that acts as a partially reflecting mirror. The planar feeding structure is a wideband leaky-wave slit dipole fed by a coplanar waveguide whose ground plane acts as a perfect reflective mirror. The measured results show that the proposed antenna has an impedance bandwidth of more than 8% (VSWR ≤ 2), a maximum gain of 13.1 dBi, and a 3 dB gain bandwidth of approximately 1.3% at a resonance frequency of around 21.6 GHz. The proposed antenna features low-profile, easy integration into circuit boards, mechanical robustness, and excellent cost-effective mass production suitability.

Sign in / Sign up

Export Citation Format

Share Document