Effect of surface treatments on the interfacial bond strength in glass fibre-polyester resin systems

1972 ◽  
Vol 2 ◽  
pp. 159 ◽  
Author(s):  
J. B. Shortall ◽  
H. W. C. Yip
Keyword(s):  
Bond Strength ◽  
Glass Fibre ◽  
Polyester Resin ◽  
Surface Treatments ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Effect Of Surface

scholarly journals Characterisation of the Interfacial bond Strength between Glass Fibre and Epoxy Resin using the Pull-Out and Push-Out Techniques

2000 ◽  
Vol 9 (3) ◽  
pp. 096369350000900 ◽  
Author(s):  
E. Mδder ◽  
X.-F. Zhou ◽  
E. Pisanova ◽  
S. Zhandarov ◽  
S. R. Nutt
Keyword(s):  
Bond Strength ◽  
Epoxy Resin ◽  
Glass Fibre ◽  
Critical Energy ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Critical Energy Release Rate ◽  
Pull Out ◽  
Loading Patterns ◽  
Push Out

Interfacial bond strength between epoxy resin and glass fibre was studied using the pull-out and push-out techniques. For untreated fibres, these micromechanical tests gave similar values of the local interfacial shear strength and critical energy release rate. In the case of fibres treated by γ-APS, both tests showed considerable increase in the bond strength. However, for the modified fibres, the pull-out test gave greater values of both interfacial parameters than the push-out test, a result attributed to the different modes of interfacial loading. The different loading patterns also cause different failure mechanisms in these two tests.

scholarly journals Effect of surface treatments on push-out bond strength of calcium silicate-based cements to fiber posts

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Amr M. Elnaghy ◽  
Ayman Mandorah ◽  
Ali H. Hassan ◽  
Alaa Elshazli ◽  
Shaymaa Elsaka
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Glass Fiber ◽  
Calcium Silicate ◽  
Surface Treatments ◽  
The Other ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Push Out ◽  
Effect Of Surface

Abstract Background To evaluate the effect of surface treatments on the push-out bond strength of Biodentine (BD) and white mineral trioxide aggregate (WMTA) to fiber posts. Methods Two brands of fiber posts were used: Reblida post; RP and RelyX post; RX. Each type of post (n = 80/group) was divided into four groups (n = 20/group) and exposed to surface treatment as follows: Control (no treatment), sandblasting (SB), hydrofluoric acid (HF), and TiF4 4 wt/v%. Each group was further subdivided into two subgroups (n = 10/subgroup) based on the type of CSCs used as follows: Subgroup A: BD and Subgroup B: WMTA. Push-out bond strength of BD and WMTA to glass fiber posts was assessed. Data were statistically analyzed using three-way ANOVA and Tukey’s test. A Weibull analysis was performed on the push-out bond strength data. Results BD showed higher bond strength than WMTA (P < 0.001). The push-out bond strength for posts treated with TiF4 4 wt/v% showed greater bond strength than the other surface treatments (P < 0.05). The BD/RP-TiF4 4 wt/v% showed the greater characteristic bond strength (σ0) (15.93) compared with the other groups. Surface treatments modified the surface topography of glass fiber posts. Conclusions The BD/RP-TiF4 4 wt/v% showed greater bond strength compared with the other groups. The TiF4 4 wt/v% surface treatment enhanced the bond strength of BD and WMTA to glass fiber posts than the other treatments. Surface treatment of fiber post with TiF4 4 wt/v% could be used to improve the bond strength with calcium silicate-based cements.

Experimental Research on Interfacial Bond Performance in Rock Anchor with High-Performance Grouting Medium

2012 ◽  
Vol 517 ◽  
pp. 932-938 ◽  
Author(s):  
Zhi Fang ◽  
Hong Qiao Zhang
Keyword(s):  
Rock Mass ◽  
Bond Strength ◽  
High Performance ◽  
Interfacial Bond ◽  
Interfacial Bond Strength ◽  
Bond Performance ◽  
Pull Out ◽  
Steel Bar ◽  
Reactive Powder ◽  
Ground Anchor

There exist the problems such as low bond strength and bad durability in the ordinary grouting slurry of the ground anchor system at present. The high-performance grouting mediums RPC (Reactive Powder Concrete) and DSP (Densified Systems containing homogeneously arranged ultrafine Particles) would become the potential replacement of grouting medium in ground anchor resulting from their high compressive strength, durability and toughness. Based on a series of pull-out tests on ground anchors with different high-performance grouting medium of RPC and DSP , different bond length in the construction field, the bond performance on the interfaces between anchor bolt (deformed steel bar) and grouted medium as well as between grouted medium and rock mass was studied. The results indicate that the interfacial bond strength between RPC or DSP and deformed steel bolt ranges within 23-31Mpa, far greater than that (about 2-3MPa) between the ordinary cementitious grout and deformed steel bar. Even though the interfacial bond strength between the grouted medium and rock mass of limestone was not obtained in the test since the failure mode was pull-out of those steel bar rather than the interface shear failure between grouted medium and rock mass, the bond stress on the interface reached 6.2-8.38 MPa, also far greater than the bond strength (about 0.1-3MPa) between the ordinary cementitious slurry and rocks.

Sign in / Sign up

Export Citation Format

Share Document