Flexible piezoelectric energy harvester with an ultrahigh transduction coefficient by the interconnected skeleton design strategy

Nanoscale ◽  
2020 ◽  
Vol 12 (24) ◽  
pp. 13001-13009
Author(s):  
Yijin Hao ◽  
Yudong Hou ◽  
Jing Fu ◽  
Xiaole Yu ◽  
Xin Gao ◽  
...  
Keyword(s):  
Composite Materials ◽  
Energy Harvester ◽  
Design Strategy ◽  
Piezoelectric Energy ◽  
Better Than

The freeze-casted 2-2 type piezocomposite has an ultrahigh transduction coefficient of 58 213 × 10−15 m2 N−1, which is significantly better than those of previously reported composite materials.

scholarly journals Models for 31-Mode PVDF Energy Harvester for Wearable Applications

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Jingjing Zhao ◽  
Zheng You
Keyword(s):  
Energy Harvester ◽  
Mechanical Energy ◽  
Electric Energy ◽  
Theoretical Models ◽  
Human Motion ◽  
Wearable Electronics ◽  
Portable Power ◽  
Renewable Power ◽  
Piezoelectric Energy ◽  
Better Than

Currently, wearable electronics are increasingly widely used, leading to an increasing need of portable power supply. As a clean and renewable power source, piezoelectric energy harvester can transfer mechanical energy into electric energy directly, and the energy harvester based on polyvinylidene difluoride (PVDF) operating in 31-mode is appropriate to harvest energy from human motion. This paper established a series of theoretical models to predict the performance of 31-mode PVDF energy harvester. Among them, the energy storage one can predict the collected energy accurately during the operation of the harvester. Based on theoretical study and experiments investigation, two approaches to improve the energy harvesting performance have been found. Furthermore, experiment results demonstrate the high accuracies of the models, which are better than 95%.

scholarly journals A Multi-Mode Broadband Vibration Energy Harvester Composed of Symmetrically Distributed U-Shaped Cantilever Beams

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 203
Author(s):  
Xiaohua Huang ◽  
Cheng Zhang ◽  
Keren Dai
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Experimental Results ◽  
Vibration Energy ◽  
Cantilever Beams ◽  
Resonant Frequencies ◽  
Promising Alternative ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Resonance Frequencies

Using the piezoelectric effect to harvest energy from surrounding vibrations is a promising alternative solution for powering small electronic devices such as wireless sensors and portable devices. A conventional piezoelectric energy harvester (PEH) can only efficiently collect energy within a small range around the resonance frequency. To realize broadband vibration energy harvesting, the idea of multiple-degrees-of-freedom (DOF) PEH to realize multiple resonant frequencies within a certain range has been recently proposed and some preliminary research has validated its feasibility. Therefore, this paper proposed a multi-DOF wideband PEH based on the frequency interval shortening mechanism to realize five resonance frequencies close enough to each other. The PEH consists of five tip masses, two U-shaped cantilever beams and a straight beam, and tuning of the resonance frequencies is realized by specific parameter design. The electrical characteristics of the PEH are analyzed by simulation and experiment, validating that the PEH can effectively expand the operating bandwidth and collect vibration energy in the low frequency. Experimental results show that the PEH has five low-frequency resonant frequencies, which are 13, 15, 18, 21 and 24 Hz; under the action of 0.5 g acceleration, the maximum output power is 52.2, 49.4, 61.3, 39.2 and 32.1 μW, respectively. In view of the difference between the simulation and the experimental results, this paper conducted an error analysis and revealed that the material parameters and parasitic capacitance are important factors that affect the simulation results. Based on the analysis, the simulation is improved for better agreement with experiments.

scholarly journals Research on a Piezoelectric Energy Harvester with Rotating Magnetic Excitation

2021 ◽  
Author(s):  
Zhe Wang ◽  
Lipeng He ◽  
Zheng Zhang ◽  
Ziming Zhou ◽  
Jianwen Zhou ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Magnetic Excitation ◽  
Piezoelectric Energy

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

scholarly journals Piezoelectric Impact Energy Harvester Based on the Composite Spherical Particle Chain for Self-Powered Sensors

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3151
Author(s):  
Shuo Yang ◽  
Bin Wu ◽  
Xiucheng Liu ◽  
Mingzhi Li ◽  
Heying Wang ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Spherical Particle ◽  
Impact Energy ◽  
Energy Harvester ◽  
Composite Particle ◽  
Piezoelectric Energy Harvesting ◽  
Particle Chain ◽  
Piezoelectric Energy ◽  
Self Powered ◽  
Particle Chains

In this study, a novel piezoelectric energy harvester (PEH) based on the array composite spherical particle chain was constructed and explored in detail through simulation and experimental verification. The power test of the PEH based on array composite particle chains in the self-powered system was realized. Firstly, the model of PEH based on the composite spherical particle chain was constructed to theoretically realize the collection, transformation, and storage of impact energy, and the advantages of a composite particle chain in the field of piezoelectric energy harvesting were verified. Secondly, an experimental system was established to test the performance of the PEH, including the stability of the system under a continuous impact load, the power adjustment under different resistances, and the influence of the number of particle chains on the energy harvesting efficiency. Finally, a self-powered supply system was established with the PEH composed of three composite particle chains to realize the power supply of the microelectronic components. This paper presents a method of collecting impact energy based on particle chain structure, and lays an experimental foundation for the application of a composite particle chain in the field of piezoelectric energy harvesting.

Wideband piezoelectric energy harvester design using parallel connection of multiple beams

2020 ◽  
Vol 12 (3) ◽  
pp. 206
Author(s):  
Sourav Naval ◽  
Prasun Kumar Sinha ◽  
Nikhil Kumar Das ◽  
Ashutosh Anand ◽  
Sudip Kundu
Keyword(s):  
Energy Harvester ◽  
Parallel Connection ◽  
Piezoelectric Energy ◽  
Multiple Beams

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

Sign in / Sign up

Export Citation Format

Share Document