Dynamics in hydrated inorganic nanotubes studied by neutron scattering: towards nanoreactors in water

Chemical reactions at a surface will in most cases show a measurable influence on the work function of the clean surface. This change of the work function δφ can be used to image the local distributions of the investigated reaction,.if one of the reacting partners is adsorbed at the surface in form of islands of sufficient size (Δ>0.2μm). These can than be visualized via a photoemission electron microscope (PEEM). Changes of φ as low as 2 meV give already a change in the total intensity of a PEEM picture. To achieve reasonable contrast for an image several 10 meV of δφ are needed. Dynamic processes as surface diffusion of CO or O on single crystal surfaces as well as reaction / diffusion fronts have been observed in real time and space.

Download Full-text

Microwaves: Application in Electron Microscopy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100158248 ◽

1990 ◽

Vol 48 (3) ◽

pp. 140-141

Author(s):

Anthony S-Y Leong ◽

David W Gove

Keyword(s):

Electron Microscopy ◽

Light Microscopy ◽

Chemical Reactions ◽

Electromagnetic Waves ◽

Tissue Fixation ◽

Primary Method ◽

Dipolar Molecules ◽

Wide Range ◽

Time Required ◽

Cryostat Sections

Microwaves (MW) are electromagnetic waves which are commonly generated at a frequency of 2.45 GHz. When dipolar molecules such as water, the polar side chains of proteins and other molecules with an uneven distribution of electrical charge are exposed to such non-ionizing radiation, they oscillate through 180° at a rate of 2,450 million cycles/s. This rapid kinetic movement results in accelerated chemical reactions and produces instantaneous heat. MWs have recently been applied to a wide range of procedures for light microscopy. MWs generated by domestic ovens have been used as a primary method of tissue fixation, it has been applied to the various stages of tissue processing as well as to a wide variety of staining procedures. This use of MWs has not only resulted in drastic reductions in the time required for tissue fixation, processing and staining, but have also produced better cytologic images in cryostat sections, and more importantly, have resulted in better preservation of cellular antigens.

Download Full-text

Local atomic structure of relaxor ferroelectric solids studied by pulsed neutron scattering

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100170505 ◽

1994 ◽

Vol 52 ◽

pp. 554-555

Author(s):

T. Egami ◽

H. D. Rosenfeld ◽

S. Teslic

Keyword(s):

Neutron Scattering ◽

Atomic Structure ◽

Argonne National Laboratory ◽

Relaxor Ferroelectrics ◽

Relaxor Ferroelectric ◽

Crystallographic Structure ◽

Chemical Inhomogeneity ◽

Distribution Analysis ◽

Ferroelectric Transition ◽

Pulsed Neutron

Relaxor ferroelectrics, such as Pb(Mg1/3Nb2/3)O3 (PMN) or (Pb·88La ·12)(Zr·65Ti·35)O3 (PLZT), show diffuse ferroelectric transition which depends upon frequency of the a.c. field. In spite of their wide use in various applications details of their atomic structure and the mechanism of relaxor ferroelectric transition are not sufficiently understood. While their crystallographic structure is cubic perovskite, ABO3, their thermal factors (apparent amplitude of thermal vibration) is quite large, suggesting local displacive disorder due to heterovalent ion mixing. Electron microscopy suggests nano-scale structural as well as chemical inhomogeneity.We have studied the atomic structure of these solids by pulsed neutron scattering using the atomic pair-distribution analysis. The measurements were made at the Intense Pulsed Neutron Source (IPNS) of Argonne National Laboratory. Pulsed neutrons are produced by a pulsed proton beam accelerated to 750 MeV hitting a uranium target at a rate of 30 Hz. Even after moderation by a liquid methane moderator high flux of epithermal neutrons with energies ranging up to few eV’s remain.

Download Full-text

Fine structure and properties of defects in naturally occurring silicates and oxides

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100175430 ◽

1990 ◽

Vol 48 (4) ◽

pp. 460-461

Author(s):

David R. Veblen

Keyword(s):

Chemical Reactions ◽

High Resolution Electron Microscopy ◽

Extended Defects ◽

Single Chain ◽

Naturally Occurring ◽

Resolution Electron ◽

Fine Structures ◽

Image Simulations ◽

Similar Crystal Structure

Extended defects and interfaces control many processes in rock-forming minerals, from chemical reactions to rock deformation. In many cases, it is not the average structure of a defect or interface that is most important, but rather the structure of defect terminations or offsets in an interface. One of the major thrusts of high-resolution electron microscopy in the earth sciences has been to identify the role of defect fine structures in reactions and to determine the structures of such features. This paper will review studies using HREM and image simulations to determine the structures of defects in silicate and oxide minerals and present several examples of the role of defects in mineral chemical reactions. In some cases, the geological occurrence can be used to constrain the diffusional properties of defects.The simplest reactions in minerals involve exsolution (precipitation) of one mineral from another with a similar crystal structure, and pyroxenes (single-chain silicates) provide a good example. Although conventional TEM studies have led to a basic understanding of this sort of phase separation in pyroxenes via spinodal decomposition or nucleation and growth, HREM has provided a much more detailed appreciation of the processes involved.

Download Full-text