scholarly journals One-step method for the preparation of cationic nanocellulose in reactive eutectic media

2021 ◽  
Vol 23 (6) ◽  
pp. 2317-2323
Author(s):  
Esther E. Jaekel ◽  
Juho Antti Sirviö ◽  
Markus Antonietti ◽  
Svitlana Filonenko

Cellulose nanocrystals were extracted and functionalized with positively charged groups in a one-step procedure applying new reactive eutectic media.

Polymers ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1071 ◽  
Author(s):  
Yu-Jin Cho ◽  
Dong-Min Kim ◽  
In-Ho Song ◽  
Ju-Young Choi ◽  
Seung-Won Jin ◽  
...  

A pyromellitic dianhydride (PMDA) and 4,4′-oxydianiline (ODA)-based oligoimide (PMDA-ODA) was synthesized by a one-step procedure using water as a solvent. The PMDA-ODA particles showed excellent partial wetting properties and were stably dispersed in both water and oil phases. A stable dispersion was not obtained with comparison PMDA-ODA particles that were synthesized by a conventional two-step method using an organic solvent. Both oil-in-water and water-in-oil Pickering emulsions were prepared using the oligoimide particles synthesized in water, and the size of the emulsion droplet was controlled based on the oligoimide particle concentration. The oligoimide particles were tested to prepare Pickering emulsions using various kinds of oils. The oil-in-water Pickering emulsions were successfully applied to prepare microcapsules of the emulsion droplets. Our new Pickering emulsion stabilizer has the advantages of easy synthesis, no need for surface modification, and the capability of stabilizing both oil-in-water and water-in-oil emulsions.


Coatings ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 40 ◽  
Author(s):  
Feng Yang ◽  
Yan Wu ◽  
Shuqin Zhang ◽  
Haiming Zhang ◽  
Suilang Zhao ◽  
...  

Developing multifunctional coatings with excellent mechanical and thermal properties is highly desirable for wood-based composite application. The recent development of waterborne coatings for wood products suggests that a promising thermosetting material needs to also have properties like low volatile organic contents (VOCs), hardness, and fast curing. The cellulose nanocrystals/graphene materials (CNC/GM) sols were prepared through the one-step method as the thermally conductive and reinforced modifier for preparing waterborne polyurethane (WPU) coatings. The influence of this modifier on the thermal and mechanical properties such as thermal conductivity, abrasion resistance, and adhesion of WPU coatings was investigated. The results indicated that adding CNC/GM sols increased the hardness, abrasion resistance, and thermal conductivity of the WPU coatings, and meanwhile maintained the coating adhesion at the highest grade (level 1). The highest abrasion resistance value of 0.023 g/100 r was obtained for the modified WPU coating when the addition of GM was 3%.


2004 ◽  
Vol 16 (2) ◽  
pp. 165
Author(s):  
L.F. Campos-Chillon ◽  
D.J. Walker ◽  
J.F. De La Torre-Sanchez

Slow-cooling techniques are widely used in cryopreservation of bovine embryos. We have previously developed a simple, two-step vitrification technique for direct transfer in the field; however, simplification to one-step vitrification would be attractive. Therefore, factorial combinations of two techniques (one-step and two-step) and two post-thaw temperatures until culture (24 and 37°C) were studied. Blastocysts (n=220) sired by two bulls were obtained in vitro in four replicates. Briefly, oocytes were aspirated from 2–8-mm follicles of ovaries obtained at a slaughterhouse, matured, fertilized and cultured in vitro with standard procedures using chemically defined media (CDM1/2 or G1/2). Two-step embryos were transferred in 1μL into 1mL of V1-CDM (5M ethylene glycol (EG) in HEPES-buffered holding medium (HCDM2)), and one-step embryos into a 7-μL droplet of V2-CDM (7M EG, 0.5M galactose and 18% w/v Ficoll 70 in HCDM2) for 3min at 24°C. Next, embryos for the two-step method were moved in 1μL into a 7μL droplet of V2-CDM at 24°C. Droplets containing embryos (one or two-step) were loaded into 0.25-mL straws preloaded with a 1-cm column of D-HCDM (0.5M galactose in HCDM2), then 0.5cm air, and then 7cm of D-HCDM followed by 0.5cm air. The column containing the embryos (0.5cm (7μL)) was followed with 0.5cm air and 1cm of D-HCDM. Straws were heat-sealed and plunged vertically, sealed end first, into liquid nitrogen just covering the embryo, and the rest of the straw was then slowly immersed. The time from loading to plunging was 40–50s. Straws were thawed in air (24°C) for 10s and then in water horizontally at 37°C until ice disappeared. Straws were gently shaken to mix the columns; then, after 5min at 24 or 37°C, embryos were expelled and cultured in CDM2+5% FCS. Re-expansion and hatching rates were evaluated 48 h post thaw. Data (Table 1) were calculated as a percentage of non-vitrified controls for respective replicates (control means: re-expansion 87%; hatching 74%) and analyzed by ANOVA. There were no main effects of post-thawing temperature (P>0.1), indicating that, after thawing, embryos can be kept at room or body temperature. Also, main effect means for re-expansion and hatching for one-step or two-step addition of cryoprotectant were similar (P>0.1), but there was a tendency for higher survival for the two-step procedure. Further refinements of the one-step technique including EG concentrations, embryological stages and equilibration times should be studied. Table 1 Main effect means (least-square means±SEM) of vitrified embryos (% of non-vitrified controls)


Small ◽  
2010 ◽  
Vol 7 (3) ◽  
pp. 302-305 ◽  
Author(s):  
Alfred C. W. Leung ◽  
Sabahudin Hrapovic ◽  
Edmond Lam ◽  
Yali Liu ◽  
Keith B. Male ◽  
...  

2016 ◽  
Vol 29 (2) ◽  
pp. 218-226 ◽  
Author(s):  
Yu Zhou ◽  
Guofei Chen ◽  
Wei Wang ◽  
Liping Song ◽  
Xingzhong Fang

Two series of polyimides (PIs) derived from bis(ether anhydride)s and bis(ester anhydride)s using 2,2′-bis(trifluoromethyl)biphenyl-4,4′-diamine were synthesized via solution polycondensation. The poly(ether imide)s could be formed by the conventional one-step method, while the poly(ester imide)s were only afforded by the two-step procedure. The resulting PIs had glass transition temperatures ( Tgs) in the range of 224–320°C and exhibited good mechanical properties with tensile strength in the range of 80.5–96.5 MPa, tensile moduli 2.7–6.9 GPa, and elongations at break 1.5–17.3%. It was found that the PIs derived from bis(ether anhydride)s showed higher thermal stability, better solubility, and transparency but lower Tg and higher water absorption compared with bis(ester anhydride)-based PIs due to the different ether and ester linkages.


1993 ◽  
Vol 58 (11) ◽  
pp. 2642-2650 ◽  
Author(s):  
Zdeněk Kruliš ◽  
Ivan Fortelný ◽  
Josef Kovář

The effect of dynamic curing of PP/EPDM blends with sulfur and thiuram disulfide systems on their mechanical properties was studied. The results were interpreted using the knowledge of the formation of phase structure in the blends during their melt mixing. It was shown, that a sufficiently slow curing reaction is necessary if a high impact strength is to be obtained. Only in such case, a fine and homogeneous dispersion of elastomer can be formed, which is the necessary condition for high impact strength of the blend. Using an inhibitor of curing in the system and a one-step method of dynamic curing leads to an increase in impact strength of blends. From the comparison of shear modulus and impact strength values, it follows that, at the stiffness, the dynamically cured blends have higher impact strength than the uncured ones.


2019 ◽  
Vol 375 ◽  
pp. 122000 ◽  
Author(s):  
Yang Xuan ◽  
Xian-Lin Song ◽  
Xiao-Quan Yang ◽  
Ruo-Yun Zhang ◽  
Zi-Yu Song ◽  
...  

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3138
Author(s):  
Kamila Gosz ◽  
Agnieszka Tercjak ◽  
Adam Olszewski ◽  
Józef Haponiuk ◽  
Łukasz Piszczyk

The utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried out at temperatures of 120, 150, and 170 °C. The resulting bio-polyols were analyzed for process efficiency, hydroxyl number, water content, viscosity, and structural features using the Fourier transform infrared spectroscopy (FTIR). The optimum liquefaction temperature was 150 °C and the time of 6 h. Comprehensive analysis of polyol properties shows high biomass conversion and hydroxyl number in the range of 238–815 mg KOH/g. This may indicate that bio-polyols may be used as a potential substitute for petrochemical polyols. During polyurethane synthesis, materials with more than 80 wt% of bio-polyol were obtained. The materials were obtained by a one-step method by hot-pressing for 15 min at 100 °C and a pressure of 5 MPa with an NCO:OH ratio of 1:1 and 1.2:1. Dynamical-mechanical analysis (DMA) showed a high modulus of elasticity in the range of 62–839 MPa which depends on the reaction conditions.


Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 783
Author(s):  
Ying Duan ◽  
Chen Wang ◽  
Jian Hao ◽  
Yang Jiao ◽  
Yanchao Xu ◽  
...  

In this paper, we propose for the first time the synthesis of α-MoO3 nanorods in a one-step procedure at mild temperatures. By changing the growth parameters, the microstructure and controllable morphology of the resulting products can be customized. The average diameter of the as-prepared nanorods is about 200 nm. The electrochromic and capacitance properties of the synthesized products were studied. The results show that the electrochromic properties of α-MoO3 nanorods at 550 nm have 67% high transmission contrast, good cycle stability and fast response time. The MoO3 nanorods also exhibit a stable supercapacitor performance with 98.5% capacitance retention after 10,000 cycles. Although current density varies sequentially, the nanostructure always exhibits a stable capacitor to maintain 100%. These results indicate the as-prepared MoO3 nanorods may be good candidates for applications in electrochromic devices and supercapacitors.


Sign in / Sign up

Export Citation Format

Share Document