Graphene-based materials: the key for the successful application of pHEMA as a blood-contacting device

2021 ◽  
Author(s):  
Andreia T. Pereira ◽  
Patrícia C. Henriques ◽  
Karl H. Schneider ◽  
Ana L. Pires ◽  
André M. Pereira ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bulk Material ◽  
Biological Properties

Incorporation of oxidized graphene improves pHEMA's mechanical properties enabling its application as bulk material in the design of blood-contacting devices. These composites keep pHEMA's biological properties, preventing thrombosis and infection.

scholarly journals Tribological and Mechanical Properties of Multicomponent CrVTiNbZr(N) Coatings

Coatings ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 41
Author(s):  
Yin-Yu Chang ◽  
Cheng-Hsi Chung
Keyword(s):  
Mechanical Properties ◽  
Nitrogen Content ◽  
Adhesion Strength ◽  
Mechanical Performance ◽  
Bulk Material ◽  
High Entropy Alloy ◽  
Composition Gradient ◽  
Multilayered Structures ◽  
High Entropy ◽  
Alloy Target

Multi-element material coating systems have received much attention for improving the mechanical performance in industry. However, they are still focused on ternary systems and seldom beyond quaternary ones. High entropy alloy (HEA) bulk material and thin films are systems that are each comprised of at least five principal metal elements in equally matched proportions, and some of them are found possessing much higher strength than traditional alloys. In this study, CrVTiNbZr high entropy alloy and nitrogen contained CrVTiNbZr(N) nitride coatings were synthesized using high ionization cathodic-arc deposition. A chromium-vanadium alloy target, a titanium-niobium alloy target and a pure zirconium target were used for the deposition. By controlling the nitrogen content and cathode current, the CrNbTiVZr(N) coating with gradient or multilayered composition control possessed different microstructures and mechanical properties. The effect of the nitrogen content on the chemical composition, microstructure and mechanical properties of the CrVTiNbZr(N) coatings was investigated. Compact columnar microstructure was obtained for the synthesized CrVTiNbZr(N) coatings. The CrVTiNbZrN coating (HEAN-N165), which was deposited with nitrogen flow rate of 165 standard cubic centimeters per minute (sccm), exhibited slightly blurred columnar and multilayered structures containing CrVN, TiNbN and ZrN. The design of multilayered CrVTiNbZrN coatings showed good adhesion strength. Improvement of adhesion strength was obtained with composition-gradient interlayers. The CrVTiNbZrN coating with nitrogen content higher than 50 at.% possessed the highest hardness (25.2 GPa) and the resistance to plastic deformation H3/E*2 (0.2 GPa) value, and therefore the lowest wear rate was obtained because of high abrasion wear resistance.

scholarly journals Assessment of Mechanical, Chemical, and Biological Properties of Ti-Nb-Zr Alloy for Medical Applications

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 126
Author(s):  
Viktoria Hoppe ◽  
Patrycja Szymczyk-Ziółkowska ◽  
Małgorzata Rusińska ◽  
Bogdan Dybała ◽  
Dominik Poradowski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Base Material ◽  
Biological Properties ◽  
Β Phase ◽  
Alloy Base ◽  
Static Tensile ◽  
Examination Methods ◽  
13Zr Alloy ◽  
Dental Applications

The purpose of this work is to obtain comprehensive reference data of the Ti-13Nb-13Zr alloy base material: its microstructure, mechanical, and physicochemical properties. In order to obtain extensive information on the tested materials, a number of examination methods were used, including SEM, XRD, and XPS to determine the phases occurring in the material, while mechanical properties were verified with static tensile, compression, and bending tests. Moreover, the alloy’s corrosion resistance in Ringer’s solution and the cytotoxicity were investigated using the MTT test. Studies have shown that this alloy has the structure α’, α, and β phases, indicating that parts of the β phase transformed to α’, which was confirmed by mechanical properties and the shape of fractures. Due to the good mechanical properties (E = 84.1 GPa), high corrosion resistance, as well as the lack of cytotoxicity on MC3T3 and NHDF cells, this alloy meets the requirements for medical implant materials. Ti-13Nb-13Zr alloy can be successfully used in implants, including bone tissue engineering products and dental applications.

Hybrid nanostructured hydroxyapatite–chitosan composite scaffold: bioinspired fabrication, mechanical properties and biological properties

2015 ◽  
Vol 3 (23) ◽  
pp. 4679-4689 ◽  
Author(s):  
Ya-Ping Guo ◽  
Jun-Jie Guan ◽  
Jun Yang ◽  
Yang Wang ◽  
Chang-Qing Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Composite Scaffold ◽  
Biological Properties ◽  
Chitosan Composite

A bioinspired strategy has been developed to fabricate a hybrid nanostructured hydroxyapatite–chitosan composite scaffold for bone tissue engineering.

scholarly journals Additive manufacturing of PLA-based scaffolds intended for bone regeneration and strategies to improve their biological properties

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 571-599
Author(s):  
Ricardo Donate ◽  
Mario Monzón ◽  
María Elena Alemán-Domínguez
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Additive Manufacturing ◽  
Bone Regeneration ◽  
Polylactic Acid ◽  
State Of The Art ◽  
Biological Properties ◽  
Design Stage ◽  
Bone Scaffolds ◽  
Regeneration Of Bone

AbstractPolylactic acid (PLA) is one of the most commonly used materials in the biomedical sector because of its processability, mechanical properties and biocompatibility. Among the different techniques that are feasible to process this biomaterial, additive manufacturing (AM) has gained attention recently, as it provides the possibility of tuning the design of the structures. This flexibility in the design stage allows the customization of the parts in order to optimize their use in the tissue engineering field. In the recent years, the application of PLA for the manufacture of bone scaffolds has been especially relevant, since numerous studies have proven the potential of this biomaterial for bone regeneration. This review contains a description of the specific requirements in the regeneration of bone and how the state of the art have tried to address them with different strategies to develop PLA-based scaffolds by AM techniques and with improved biofunctionality.

scholarly journals Biological and Mechanical Properties of Platelet-Rich Fibrin Membranes after Thermal Manipulation and Preparation in a Single-Syringe Closed System

2018 ◽  
Vol 19 (11) ◽  
pp. 3433 ◽  
Author(s):  
Dorottya Kardos ◽  
István Hornyák ◽  
Melinda Simon ◽  
Adél Hinsenkamp ◽  
Bence Marschall ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cell Adhesion ◽  
Closed System ◽  
Three Dimensional ◽  
Glass Tube ◽  
Biological Properties ◽  
Platelet Rich Fibrin ◽  
Handling Characteristics ◽  
Freeze Dried

Platelet-rich fibrin (PRF) membrane is a three-dimensional biodegradable biopolymer, which consists of platelet derived growth factors enhancing cell adhesion and proliferation. It is widely used in soft and hard tissue regeneration, however, there are unresolved problems with its clinical application. Its preparation needs open handling of the membranes, it degrades easily, and it has a low tensile strength which does not hold a suture blocking wider clinical applications of PRF. Our aim was to produce a sterile, suturable, reproducible PRF membrane suitable for surgical intervention. We compared the biological and mechanical properties of PRF membranes created by the classical glass-tube and those that were created in a single-syringe closed system (hypACT Inject), which allowed aseptic preparation. HypACT Inject device produces a PRF membrane with better handling characteristics without compromising biological properties. Freeze-thawing resulted in significantly higher tensile strength and higher cell adhesion at a lower degradation rate of the membranes. Mesenchymal stem cells seeded onto PRF membranes readily proliferated on the surface of fresh, but even better on freeze/thawed or freeze-dried membranes. These data show that PRF membranes can be made sterile, more uniform and significantly stronger which makes it possible to use them as suturable surgical membranes.

Characterization of AM60 Magnesium Alloy Prepared by Rapid Solidification and Plastic Consolidation Technique

2010 ◽  
Vol 667-669 ◽  
pp. 997-1002
Author(s):  
Tomasz Tokarski
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloy ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Bulk Material ◽  
Structure Refinement ◽  
Hot Extrusion ◽  
Solidification Process ◽  
Protective Atmosphere ◽  
Material Structure

Magnesium and its alloys are attractive candidates for automotive and aerospace applications due to their relatively high strength and low density. However, their low ductility determined by hcp structure of material results in limitation of plastic deformation processing. In order to improve ductility as well as mechanical properties, structure refinement processes can be used. It is well known that effective refining of the material structure can be achieved by increasing the cooling rate during casting procedures, hence rapid solidification process (RSP) has been experimented for the fabrication of magnesium alloys. The present paper reports an experimental investigation on the influence of rapid solidification on the mechanical properties of AM60 magnesium alloy. In order to obtain RS material melt spinning process was applied in protective atmosphere, resulting in formation of RS ribbons. Following consolidation of the RS material is necessary to obtain bulk material with high mechanical properties, as so hot extrusion process was applied. It was noticed that application of plastic consolidation by hot extrusion is the most effective process to achieve full densification of material. For comparison purposes, the conventionally cast and hot extruded AM60 alloy was studied as well. The purpose of the present study was to investigate in detail the effect of rapid solidification and extrusion temperature on the structure and mechanical properties of the materials.

scholarly journals Porous Cellulose-Collagen Scaffolds For Soft Tissue Regeneration: Influence of Cellulose Derivatives On Mechanical Properties And Compatibility With Adipose-Derived Stem Cells.

2022 ◽  
Author(s):  
Katarína Kacvinská ◽  
Martina Trávničková ◽  
Lucy Vojtová ◽  
Petr Poláček ◽  
Jana Dorazilová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Stem Cells ◽  
Cell Adhesion ◽  
Soft Tissue ◽  
Vascular Tissue ◽  
Biological Properties ◽  
Cellulose Derivatives ◽  
Adipose Derived Stem Cells ◽  
Soft Tissue Regeneration

Abstract This study deals with cellulose derivatives in relation to the collagen fibrils in composite collagen-cellulose scaffolds for soft tissue engineering. Two types of cellulose, i.e., oxidized cellulose (OC) and carboxymethyl cellulose (CMC), were blended with collagen (Col) to enhance its elasticity, stability and sorptive biological properties, e.g. hemostatic and antibacterial features. The addition of OC supported the resistivity of the Col fibrils in a dry environment, while in a moist environment OC caused a radical drop. The addition of CMC reduced the mechanical strength of the Col fibrils in both environments. The elongation of the Col fibrils was increased by both types of cellulose derivatives in both environments, which is closely related to tissue like behaviour. In these various mechanical environments, the ability of human adipose-derived stem cells (hADSCs) to adhere and proliferate was significantly greater in the Col and Col/OC scaffolds than in the Col/CMC scaffold. This is explained by deficient mechanical support and loss of stiffness due to the high swelling capacity of CMC. Although Col/OC and Col/CMC acted differently in terms of mechanical properties, both materials were observed to be cytocompatible, with varying degrees of further support for cell adhesion and proliferation. While Col/OC can serve as a scaffolding material for vascular tissue engineering and for skin tissue engineering, Col/CMC seems to be more suitable for moist wound healing, e.g. as a mucoadhesive gel for exudate removal, since there was almost no cell adhesion.

Tantalum as a Novel Biomaterial for Bone Implant: A Literature Review

2021 ◽  
Vol 52 ◽  
pp. 55-65
Author(s):  
Ivan Putrantyo ◽  
Nikhit Anilbhai ◽  
Revati Vanjani ◽  
Brigita De Vega
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Dental Implants ◽  
Bulk Material ◽  
High Melting Point ◽  
Design Modification ◽  
Bone Implant ◽  
Specific Strength ◽  
Metallic Implants ◽  
Tantalum Coatings

Titanium (Ti) has been used in metallic implants since the 1950s due to various biocompatible and mechanical properties. However, due to its high Young’s modulus, it has been modified over the years in order to produce a better biomaterial. Tantalum (Ta) has recently emerged as a new potential biomaterial for bone and dental implants. It has been reported to have better corrosion resistance and osteo-regenerative properties as compared to Ti alloys which are most widely used in the bone-implant industry. Currently, Tantalum cannot be widely used yet due to its limited availability, high melting point, and high-cost production. This review paper discusses various manufacturing methods of Tantalum alloys, including conventional and additive manufacturing and also discusses their drawbacks and shortcomings. Recent research includes surface modification of various metals using Tantalum coatings in order to combine bulk material properties of different materials and the porous surface properties of Tantalum. Design modification also plays a crucial role in controlling bulk properties. The porous design does provide a lower density, wider surface area, and more immense specific strength. In addition to improved mechanical properties, a porous design could also escalate the material's biological and permeability properties. With current advancement in additive manufacturing technology, difficulties in processing Tantalum could be resolved. Therefore, Tantalum should be considered as a serious candidate material for future bone and dental implants.

scholarly journals Brushite cement containing gelatin: evaluation of mechanical strength and in vitro degradation

Cerâmica ◽  
2019 ◽  
Vol 65 (374) ◽  
pp. 261-266 ◽  
Author(s):  
L. P. Silva ◽  
M. D. P. Ribeiro ◽  
E. S. Trichês ◽  
M. Motisuke
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Solid Phase ◽  
Setting Time ◽  
Biological Properties ◽  
Solubility In Water ◽  
Ringer’S Solution ◽  
Weight Loss Data

Abstract Calcium phosphate cements (CPCs) are potential materials for repairing bone defects, mainly due to their excellent biocompatibility and osteoconductivity. Nevertheless, their low mechanical properties limit their usage in clinical applications. The gelatin addition may improve the mechanical and biological properties of CPCs, but their solubility in water may increase the porosity of the cement during degradation. Thus, the aim of this work was to investigate the influence of gelatin on the setting time, compressive strength and degradation rate of a brushite cement. CPCs were prepared with the addition of 0, 5, 10 and 20 wt% of gelatin powder in the solid phase of the cement. The results indicated that the setting time increased with gelatin. Furthermore, cement with 20 wt% of gelatin had an initial compressive strength of 14.1±1.8 MPa while cement without gelatin had 4.5±1.2 MPa. The weight loss, morphology and compressive strength were evaluated after degradation in Ringer’s solution. According to the weight loss data, gelatin was eliminated of samples during degradation. It was concluded that the presence of gelatin improved CPCs mechanical properties; however, as degradation in Ringer’s solution evolved, cement compressive strength decreased due to gelatin dissolution and, consequently, an increase in sample porosity.

Sign in / Sign up

Export Citation Format

Share Document