Phase change material with anisotropically high thermal conductivity and excellent shape stability due to its robust cellulose/BNNSs skeleton

2019 ◽  
Vol 7 (33) ◽  
pp. 19364-19373 ◽  
Author(s):  
Chuxin Lei ◽  
Kai Wu ◽  
Lingyu Wu ◽  
Wenjie Liu ◽  
Rongni Du ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Energy Storage ◽  
Thermal Management ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage Material ◽  
Shape Stability ◽  
Energy Storage Material ◽  
Thermal Energy Storage Material ◽  
Change Material

An anisotropic and robust 3D interconnected cellulose/BNNSs skeleton was designed within PEG composites for thermal management and as a solar light-to-thermal energy storage material.

Experimental Study of Thermal Energy Storage System

2000 ◽  
Author(s):  
Bing-Chwen Yang ◽  
Shr-Hau Huang ◽  
Hsiang-Hui Lin
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage Material ◽  
Heating Chamber ◽  
Heating And Cooling ◽  
Energy Storage Material ◽  
Thermal Energy Storage Material ◽  
Change Material

Abstract In this paper, the feasibility of phase change material that used for thermal energy storage in the range of 400 ∼ 600°C in the form of latent heat is examined for nine different salts and eutectic salts. The Differential Scanning Calorimeter (DSC) was used to perform the quantitative measurement of the phase change temperature (Tm) and latent heat (ΔH). The thermal properties of NaCl-CaCl2 at repeated heating and cooling cycles were studied with a heating chamber. The quality observation for this phase change material was also performed with this heating chamber to understand its physical phenomena during heating and cooling process. It is found that NaCl-CaCl2 is a good candidate of thermal energy storage material for its stable properties, low cost, and no toxic. Finally, the thermal storage unit with NaCl-CaCl2 as thermal energy storage material was tested to study and evaluate its performance as the application in the waste heat recovery system.

Waste From Metallurgic Industry: A Sustainable High-Temperature Thermal Energy Storage Material for Concentrated Solar Power

2013 ◽  
Author(s):  
Nicolas Calvet ◽  
Guilhem Dejean ◽  
Lucía Unamunzaga ◽  
Xavier Py
Keyword(s):  
Heat Capacity ◽  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Solar Power ◽  
Low Cost ◽  
Concentrated Solar Power ◽  
Storage Material ◽  
Energy Storage Material ◽  
Thermal Energy Storage Material

The ambitious DOE SunShot cost target ($0.06/kWh) for concentrated solar power (CSP) requires innovative concepts in the collector, receiver, and power cycle subsystems, as well as in thermal energy storage (TES). For the TES, one innovative approach is to recycle waste from metallurgic industry, called slags, as low-cost high-temperature thermal energy storage material. The slags are all the non-metallic parts of cast iron which naturally rises up by lower density at the surface of the fusion in the furnace. Once cooled down some ceramic can be obtained mainly composed of oxides of calcium, silicon, iron, and aluminum. These ceramics are widely available in USA, about 120 sites in 32 States and are sold at a very low average price of $5.37/ton. The US production of iron and steel slag was estimated at 19.7 million tons in 2003 which guarantees a huge availability of material. In this paper, electric arc furnace (EAF) slags from steelmaking industry, also called “black slags”, were characterized in the range of temperatures of concentrated solar power. The raw material is thermo-chemically stable up to 1100 °C and presents a low cost per unit thermal energy stored ($0.21/kWht for ΔT = 100 °C) and a suitable heat capacity per unit volume of material (63 kWht/m3for ΔT = 100°C). These properties should enable the development of new TES systems that could achieve the TES targets of the SunShot (temperature above 600 °C, installed cost below $15/kWht, and heat capacity ≥25 kWht/m3). The detailed experimental results are presented in the paper. After its characterization, the material has been shaped in form of plates and thermally cycled in a TES system using hot-air as heat transfer fluid. Several cycles of charge and discharged were performed successfully and the concept was validated at laboratory scale. Apart from availability, low-cost, and promising thermal properties, the use of slag promotes the conservation of natural resources and is a noble solution to decrease the cost and to develop sustainable TES systems.

Thermophysical characterization of a by-product from the steel industry to be used as a sustainable and low-cost thermal energy storage material

Energy ◽  
2015 ◽  
Vol 89 ◽  
pp. 601-609 ◽  
Author(s):  
Iñigo Ortega-Fernández ◽  
Nicolas Calvet ◽  
Antoni Gil ◽  
Javier Rodríguez-Aseguinolaza ◽  
Abdessamad Faik ◽  
...  
Keyword(s):  
Energy Storage ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Steel Industry ◽  
Low Cost ◽  
Storage Material ◽  
Energy Storage Material ◽  
Thermal Energy Storage Material ◽  
Thermophysical Characterization
Sign in / Sign up

Export Citation Format

Share Document