Effect of nanoparticle size on the mechanical properties of nanoparticle assemblies

Nanoscale ◽  
2019 ◽  
Vol 11 (19) ◽  
pp. 9563-9573 ◽  
Author(s):  
Lu An ◽  
Di Zhang ◽  
Lin Zhang ◽  
Gang Feng
Keyword(s):  
Mechanical Properties ◽  
Nanoparticle Size ◽  
Nanoparticle Assemblies

Nanoparticle (NP) assembly becomes drastically harder (∼39×) and stiffer (∼15×) by decreasing the NP size (d).

scholarly journals Influence of nanoparticle size, loading, and shape on the mechanical properties of polymer nanocomposites

2012 ◽  
Vol 137 (21) ◽  
pp. 214901 ◽  
Author(s):  
Aki Kutvonen ◽  
Giulia Rossi ◽  
Sakari R. Puisto ◽  
Niko K. J. Rostedt ◽  
Tapio Ala-Nissila
Keyword(s):  
Mechanical Properties ◽  
Polymer Nanocomposites ◽  
Nanoparticle Size

Effects of nanoparticle size and content on mechanical properties of dental nanocomposites: experimental versus modeling

2015 ◽  
Vol 24 (10) ◽  
pp. 837-848 ◽  
Author(s):  
Hamideh Barghamadi ◽  
Mohammad Atai ◽  
Mohammad Imani ◽  
Masoud Esfandeh
Keyword(s):  
Mechanical Properties ◽  
Nanoparticle Size ◽  
Experimental Versus

Effects of Nanoparticle Size on the Thermoelectric and Mechanical Properties of Skutterudite Nanocomposites

2014 ◽  
Vol 43 (6) ◽  
pp. 2115-2120 ◽  
Author(s):  
Bo Duan ◽  
Pengcheng Zhai ◽  
Shijie Ding ◽  
Chenglong Xu ◽  
Guodong Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Nanoparticle Size

Phase Transformations in Ti-7w/oMo-3w/oMe Alloy

1974 ◽  
Vol 32 ◽  
pp. 514-515
Author(s):  
S. Fujishiro
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Processing ◽  
Ray Method ◽  
X Ray ◽  
Transmission Electron ◽  
Water Quench ◽  
Alpha Beta

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Lattice Imaging of Grain Boundaries in Ceramics

1977 ◽  
Vol 35 ◽  
pp. 114-115
Author(s):  
D. R. Clarke ◽  
G. Thomas
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Grain Boundaries ◽  
High Temperature Strength ◽  
Current Interest ◽  
Lattice Imaging ◽  
Special Significance ◽  
Structural Applications ◽  
Refractory Ceramics

Grain boundaries have long held a special significance to ceramicists. In part, this has been because it has been impossible until now to actually observe the boundaries themselves. Just as important, however, is the fact that the grain boundaries and their environs have a determing influence on both the mechanisms by which powder compaction occurs during fabrication, and on the overall mechanical properties of the material. One area where the grain boundary plays a particularly important role is in the high temperature strength of hot-pressed ceramics. This is a subject of current interest as extensive efforts are being made to develop ceramics, such as silicon nitride alloys, for high temperature structural applications. In this presentation we describe how the techniques of lattice fringe imaging have made it possible to study the grain boundaries in a number of refractory ceramics, and illustrate some of the findings.

Sign in / Sign up

Export Citation Format

Share Document