Facile preparation of COF composite membranes for nanofiltration by stoichiometric spraying layer-by-layer self-assembly

2020 ◽  
Vol 56 (3) ◽  
pp. 419-422 ◽  
Author(s):  
Shuang Hao ◽  
Lu Jiang ◽  
Yongliang Li ◽  
Zhiqian Jia ◽  
Bart Van der Bruggen
Keyword(s):  
Self Assembly ◽  
Composite Membranes ◽  
Layer By Layer ◽  
Excellent Performance ◽  
Assembly Method ◽  
Facile Preparation

COF–LZU1 membranes are prepared by a stoichiometric spraying layer-by-layer self-assembly method and the membranes display excellent performance for dye separation.

scholarly journals Layer-by-layer self-assembly preparation and desalination performance of graphene oxide membrane

2021 ◽  
Author(s):  
Jun Hu ◽  
Zuoguo Yang
Keyword(s):  
Graphene Oxide ◽  
Self Assembly ◽  
Composite Membranes ◽  
Rejection Rate ◽  
Cationic Polyelectrolyte ◽  
Layer By Layer ◽  
Operating Pressure ◽  
High Flux ◽  
Assembly Method ◽  
Multi Stage

Abstract Unlike previous utilization of ultrafiltration membranes as supporters of graphene oxide (GO) composite membranes, this study first adopts microporous nylon membranes as substrates. The cationic polyelectrolyte/GO composite membranes are prepared by the layer-by-layer self-assembly method via electrostatic attraction. The introduction of polycations between nanochannels in the GO membranes effectively suppresses the swelling and improves the stability of the membranes. It is found that the polyelectrolytes' charge density and the surface potential of the composite membranes jointly determine the membranes' properties. The experimental results show that the novel GO membranes can obtain high flux and considerable desalination performance under low operating pressure. Typically, the salt rejection rate reaches 66.8% for 1.0 g/L MgSO4, and the flux is 39.8 L·m−2·h−1·bar−1. Benefitting from the GO composite membranes keeping similar retention for both high and low concentration salt solutions, the ideal desalination performance could be obtained through multi-stage processes on the premise of ensuring high flux, which is more suitable for industry.

Layer-by-layer self-assembly of PDDA/PWA–Nafion composite membranes for direct methanol fuel cells

2010 ◽  
Vol 46 (9) ◽  
pp. 1434 ◽  
Author(s):  
Meng Yang ◽  
Shanfu Lu ◽  
Jinlin Lu ◽  
San Ping Jiang ◽  
Yan Xiang
Keyword(s):  
Fuel Cells ◽  
Self Assembly ◽  
Direct Methanol Fuel Cells ◽  
Composite Membranes ◽  
Layer By Layer ◽  
Direct Methanol ◽  
Methanol Fuel Cells

Hydrogen-Bonding Layer Protecting Polyelectrolyte Capsules and Its Mechanical Property Study with Atomic Force Microscope

2008 ◽  
Vol 8 (6) ◽  
pp. 2996-3002 ◽  
Author(s):  
Liqin Ge ◽  
Xing Wang ◽  
Long Ba ◽  
Zhongze Gu
Keyword(s):  
Hydrogen Bonding ◽  
Atomic Force Microscope ◽  
Elastic Deformation ◽  
Self Assembly ◽  
Laser Scanning ◽  
Confocal Laser ◽  
Bonding Layer ◽  
Layer By Layer ◽  
Assembly Method ◽  
Atomic Force

The hydrogen-bonding multilayered polyelectrolyte capsules with sizes around 6 μm were fabricated by layer-by-layer self-assembly method. The morphology of the obtained capsules was observed with Scanning Electron Microscope (SEM), Confocal Laser Scanning Microscope (CLSM) and Atomic Force Microscope (AFM), respectively. The elastic properties of the capsules were studied with AFM. The capsule was pressed by cantilever with different lengths, a glass bead glued at the end of the cantilever. The force curves were measured on the capsule in air. The Young's modulus of the capsule was obtained (E = 170 MPa for the loading). Results show that this model can predict the elastic deformation of the microcapsule. The accuracy of the elastic deformation of polymer capsule can be ensured using a cantilever of mediate stiffness. Our results show that the existence of the hydrogen-bonding layer makes the multilayered polyelectrolyte harder in comparison with the pure multilayered polyelectrolyte capsules.

Fabrication of montmorillonite and titanate nanotube based coatings via layer-by-layer self-assembly method to enhance the thermal stability, flame retardancy and ultraviolet protection of polyethylene terephthalate (PET) fabric

RSC Advances ◽  
2016 ◽  
Vol 6 (59) ◽  
pp. 53625-53634 ◽  
Author(s):  
Ying Pan ◽  
Wei Wang ◽  
Haifeng Pan ◽  
Jing Zhan ◽  
Yuan Hu
Keyword(s):  
Thermal Stability ◽  
Polyethylene Terephthalate ◽  
Flame Retardancy ◽  
Self Assembly ◽  
Layer By Layer ◽  
Pet Fabric ◽  
Thermal Oxidative Stability ◽  
Titanate Nanotube ◽  
Assembly Method ◽  
Ultraviolet Protection

Montmorillonite and titanate nanotube based coatings have been prepared through LbL self-assembly method, in order to enhance the thermal and thermal-oxidative stability, flame retardancy and UV protection of polyethylene terephthalate fabric.

A wearable and highly sensitive strain sensor based on a polyethylenimine–rGO layered nanocomposite thin film

2017 ◽  
Vol 5 (31) ◽  
pp. 7746-7752 ◽  
Author(s):  
Xueliang Ye ◽  
Zhen Yuan ◽  
Huiling Tai ◽  
Weizhi Li ◽  
Xiaosong Du ◽  
...  
Keyword(s):  
Thin Film ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Self Assembly ◽  
Strain Sensor ◽  
Layer By Layer ◽  
Nanocomposite Thin Film ◽  
Assembly Method ◽  
Reduced Graphene ◽  
Highly Sensitive

A novel strain sensor based on reduced graphene oxide with ultra-sensitive and ultra-durable performance was fabricated by the chemical layer-by-layer self-assembly method.

Functionalization of membrane surface by layer-by-layer self-assembly method for dyes removal

2020 ◽  
Vol 134 ◽  
pp. 140-148 ◽  
Author(s):  
Eduarda Freitas Diogo Januário ◽  
Natália de Camargo Lima Beluci ◽  
Taynara Basso Vidovix ◽  
Marcelo Fernandes Vieira ◽  
Rosângela Bergamasco ◽  
...  
Keyword(s):  
Self Assembly ◽  
Membrane Surface ◽  
Layer By Layer ◽  
Assembly Method ◽  
Dyes Removal

Construction of multilayer films with bactericidal and long-term antitumor drug release properties as a non-vascular stent coating for therapy in obstruction

2019 ◽  
Vol 7 (32) ◽  
pp. 4963-4972 ◽  
Author(s):  
Xiao-yan Xu ◽  
Yan-fang Chen ◽  
Qing-gang Tan ◽  
Zhi-jie Chen ◽  
Yan Li ◽  
...  
Keyword(s):  
Drug Release ◽  
Self Assembly ◽  
Multilayer Films ◽  
Antitumor Drug ◽  
Layer By Layer ◽  
Vascular Stent ◽  
Assembly Method ◽  
Stent Coating

An antibacterial and antitumor coating for non-vascular stent was constructed via the layer-by-layer electrostatic self-assembly method.

Sign in / Sign up

Export Citation Format

Share Document