Flexible cellulose nanopaper with high wet tensile strength, high toughness and tunable ultraviolet blocking ability fabricated from tobacco stalk via a sustainable method

2018 ◽  
Vol 6 (27) ◽  
pp. 13021-13030 ◽  
Author(s):  
Qingbo Wang ◽  
Haishun Du ◽  
Fang Zhang ◽  
Yuedong Zhang ◽  
Meiyan Wu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Mechanical Performance ◽  
Residual Lignin ◽  
Wet Strength ◽  
High Toughness ◽  
Uv Blocking ◽  
Cellulose Nanopaper ◽  
Tobacco Stalk

Retaining residual lignin in nanopaper leads to UV-blocking ability and significantly improves mechanical performance, especially the toughness and wet strength.

Enabled Cellulose Nanopaper with Outstanding Water Stability and Wet Strength via Activated Residual Lignin as a Reinforcement

2021 ◽  
Author(s):  
jinlong wang ◽  
Wei Chen ◽  
Tengteng Dong ◽  
Haiqi Wang ◽  
Shurun Si ◽  
...  
Keyword(s):  
Hydrogen Bonding ◽  
Plant Cell ◽  
Cell Walls ◽  
Water Stability ◽  
Plant Cell Walls ◽  
Residual Lignin ◽  
Wet Strength ◽  
Cellulose Nanopaper

Due to water-sensitive hydrogen bonding, uncontrolled deformation and mechanical decay of cellulose nanopaper (CNP) caused by water remain challenging. Inspired by plant cell walls and bonding strengthening, a strategy is...

Effect of Polyethylene Glycol in Nanocellulose/PLA Composites

2019 ◽  
Vol 821 ◽  
pp. 89-95
Author(s):  
Wanasorn Somphol ◽  
Thipjak Na Lampang ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Polyethylene Glycol ◽  
Aspect Ratio ◽  
Mechanical Performance ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Solvent Casting ◽  
Casting Method ◽  
Mediated Oxidation

Poly (lactic acid) or PLA was reinforced by nanocellulose and polyethylene glycol (PEG), which were introduced into PLA matrix from 0 to 3 wt.% to enhance compatibility and strength of the PLA. The nanocellulose was prepared by TEMPO-mediated oxidation from microcrystalline cellulose (MCC) powder and characterized by TEM, AFM, and XRD to reveal rod-like shaped nanocellulose with nanosized dimensions, high aspect ratio and high crystallinity. Films of nanocellulose/PEG/PLA nanocomposites were prepared by solvent casting method to evaluate the mechanical performance. It was found that the addition of PEG in nanocellulose-containing PLA films resulted in an increase in tensile modulus with only 1 wt% of PEG, where higher PEG concentrations negatively impacted the tensile strength. Furthermore, the tensile strength and modulus of nanocellulose/PEG/PLA nanocomposites were higher than the PLA/PEG composites due to the existence of nanocellulose chains. Visual traces of crazing were detailed to describe the deformation mechanism.

Microstructure and mechanical property improvement of dissimilar metal joints for TC4 Ti alloy to Nitinol NiTi alloy by laser welding

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Yan Zhang ◽  
DeShui Yu ◽  
JianPing Zhou ◽  
DaQian Sun ◽  
HongMei Li
Keyword(s):  
Tensile Strength ◽  
Laser Welding ◽  
Mechanical Performance ◽  
Niti Alloy ◽  
Welding Process ◽  
Ti Alloy ◽  
The One ◽  
Fusion Weld ◽  
Welding Processes ◽  
Cu Interlayer

Abstract To avoid the formation of Ti-Ni intermetallics in a joint, three laser welding processes for Ti alloy–NiTi alloy joints were introduced. Sample A was formed while a laser acted at the Ti alloy–NiTi alloy interface, and the joint fractured along the weld centre line immediately after welding without filler metal. Sample B was formed while the laser acted on a Cu interlayer. The average tensile strength of sample B was 216 MPa. Sample C was formed while the laser acted 1.2 mm on the Ti alloy side. The one-pass welding process involved the creation of a joint with one fusion weld and one diffusion weld separated by the remaining unmelted Ti alloy. The mechanical performance of sample C was determined by the diffusion weld formed at the Ti alloy–NiTi alloy interface with a tensile strength of 256 MPa.

scholarly journals Enhanced Tensile Strength of Monolithic Epoxy with Highly Dispersed TiO2-Graphene Nanocomposites

2021 ◽  
Vol 5 (7) ◽  
pp. 191
Author(s):  
Yanshuai Wang ◽  
Siyao Guo ◽  
Biqin Dong ◽  
Feng Xing
Keyword(s):  
Tensile Strength ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Chemical Properties ◽  
High Mechanical Property ◽  
Graphene Nanocomposites ◽  
Highly Dispersed ◽  
Dispersion State ◽  
Physical And Chemical

The functionalization of graphene has been reported widely, showing special physical and chemical properties. However, due to the lack of surface functional groups, the poor dispersibility of graphene in solvents strongly limits its engineering applications. This paper develops a novel green “in-situ titania intercalation” method to prepare a highly dispersed graphene, which is enabled by the generation of the titania precursor between the layer of graphene at room temperature to yield titania-graphene nanocomposites (TiO2-RGO). The precursor of titania will produce amounts of nano titania between the graphene interlayers, which can effectively resist the interfacial van der Waals force of the interlamination in graphene for improved dispersion state. Such highly dispersed TiO2-RGO nanocomposites were used to modify epoxy resin. Surprisingly, significant enhancement of the mechanical performance of epoxy resin was observed when incorporating the titania-graphene nanocomposites, especially the improvements in tensile strength and elongation at break, with 75.54% and 176.61% increases at optimal usage compared to the pure epoxy, respectively. The approach presented herein is easy and economical for industry production, which can be potentially applied to the research of high mechanical property graphene/epoxy composite system.

scholarly journals A Comprehensive Investigation on 3D Printing of Polyamide 11 and Thermoplastic Polyurethane via Multi Jet Fusion

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2139
Author(s):  
Wei Shian Tey ◽  
Chao Cai ◽  
Kun Zhou
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Wear Rate ◽  
Mechanical Performance ◽  
Thermoplastic Polyurethane ◽  
Print Quality ◽  
Polyamide 11 ◽  
Powder Bed

Multi Jet Fusion (MJF) is a recently developed polymeric powder bed fusion (PBF) additive manufacturing technique that has received considerable attention in the industrial and scientific community due to its ability to fabricate functional and complex polymeric parts efficiently. In this work, a systematic characterization of the physicochemical properties of MJF-certified polyamide 11 (PA11) and thermoplastic polyurethane (TPU) powder was conducted. The mechanical performance and print quality of the specimens printed using both powders were then evaluated. Both PA11 and TPU powders showed irregular morphology with sharp features and had broad particle size distribution, but such features did not impair their printability significantly. According to the DSC scans, the PA11 specimen exhibited two endothermic peaks, while the TPU specimen exhibited a broad endothermic peak (116–150 °C). The PA11 specimens possessed the highest tensile strength in the Z orientation, as opposed to the TPU specimens which possessed the lowest tensile strength along the same orientation. The flexural properties of the PA11 and TPU specimens displayed a similar anisotropy where the flexural strength was highest in the Z orientation and lowest in the X orientation. The porosity values of both the PA11 and the TPU specimens were observed to be the lowest in the Z orientation and highest in the X orientation, which was the opposite of the trend observed for the flexural strength of the specimens. The PA11 specimen possessed a low coefficient of friction (COF) of 0.13 and wear rate of 8.68 × 10−5 mm3/Nm as compared to the TPU specimen, which had a COF of 0.55 and wear rate of 0.012 mm3/Nm. The PA11 specimens generally had lower roughness values on their surfaces (Ra < 25 μm), while the TPU specimens had much rougher surfaces (Ra > 40 μm). This investigation aims to uncover and explain phenomena that are unique to the MJF process of PA11 and TPU while also serving as a benchmark against similar polymeric parts printed using other PBF processes.

Biomechanical comparison of the Lim/Tsai tendon repair with a modified method using a single looped suture

2017 ◽  
Vol 42 (9) ◽  
pp. 915-919 ◽  
Author(s):  
Min Kai Chang ◽  
Yoke Rung Wong ◽  
Shian Chao Tay
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Mechanical Performance ◽  
Tendon Repair ◽  
Original Method ◽  
Flexor Digitorum Profundus ◽  
Loading Test ◽  
Modified Method ◽  
Cycle Loading ◽  
The Difference

The Lim/Tsai tendon repair technique has been modified clinically to achieve a 6-strand repair using a single looped suture with one extratendinous knot. We compared biomechanical performance of the original and modified methods using 20 porcine flexor digitorum profundus tendons. The ultimate tensile strength, load to 2 mm gap force, mode of failure, and time taken to repair each tendon were recorded during a single cycle loading test in 10 tendons with each repair method. We found that despite having the same number of core strands, the single looped suture modified Lim/Tsai technique possessed significantly greater ultimate tensile strength and load to 2 mm gap force. Also, less repair time was required. We conclude that the modified 6-strand repair using a single looped suture has better mechanical performance than the original method. The difference likely was due to the changes in locations of the knots and subsequent load distribution during tendon loading.

scholarly journals The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis

Materials ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1333 ◽  
Author(s):  
Adrián Rodríguez-Panes ◽  
Juan Claver ◽  
Ana Camacho
Keyword(s):  
Tensile Strength ◽  
Mechanical Behaviour ◽  
Mechanical Performance ◽  
Acrylonitrile Butadiene Styrene ◽  
Polymer Materials ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Layer Orientation ◽  
Lower Variability

This paper presents a comparative study of the tensile mechanical behaviour of pieces produced using the Fused Deposition Modelling (FDM) additive manufacturing technique with respect to the two types of thermoplastic material most widely used in this technique: polylactide (PLA) and acrylonitrile butadiene styrene (ABS). The aim of this study is to compare the effect of layer height, infill density, and layer orientation on the mechanical performance of PLA and ABS test specimens. The variables under study here are tensile yield stress, tensile strength, nominal strain at break, and modulus of elasticity. The results obtained with ABS show a lower variability than those obtained with PLA. In general, the infill percentage is the manufacturing parameter of greatest influence on the results, although the effect is more noticeable in PLA than in ABS. The test specimens manufactured using PLA perform more rigidly and they are found to have greater tensile strength than ABS. The bond between layers in PLA turns out to be extremely strong and is, therefore, highly suitable for use in additive technologies. The methodology proposed is a reference of interest in studies involving the determination of mechanical properties of polymer materials manufactured using these technologies.

Water and humidity-induced shape memory cellulose nanopaper with quick response, excellent wet strength and folding resistance

2020 ◽  
Vol 392 ◽  
pp. 123673 ◽  
Author(s):  
Meiyan Wu ◽  
Prakit Sukyai ◽  
Dong Lv ◽  
Fang Zhang ◽  
Peidong Wang ◽  
...  
Keyword(s):  
Shape Memory ◽  
Quick Response ◽  
Wet Strength ◽  
Cellulose Nanopaper

scholarly journals Tensile Performance of a Novel Glue-Laminated Cornstalk Scrimber

2020 ◽  
Vol 23 (3) ◽  
pp. 198-203
Author(s):  
Wei Tian ◽  
Yongmei Qian ◽  
Ruozhu Wang ◽  
Yiming Wang
Keyword(s):  
High Pressure ◽  
Tensile Strength ◽  
Experimental Analysis ◽  
Building Material ◽  
Mechanical Performance ◽  
Strain Curve ◽  
Cost Effective ◽  
Building Industry ◽  
Young’S Moduli ◽  
Tensile Performance

Glue-laminated cornstalk scrimber is a novel composite to substitute timber. This composite can be prepared in three steps: selecting flawless cornstalks, laying them parallel to grain, and gluing the scrimbers under high pressure. Compared with ordinary timber, glue-laminated cornstalk scrimber excels in the resistance to water, damping, insect, and fire. It is therefore widely recognized as novel eco-friendly and cost- effective composite with great potential in the building industry. The tensile strength of glue-laminated cornstalk scrimber mainly depends on the parallel-to-grain strength of its fibers. The mechanical performance parallel to grain directly determines that of this composite. Hence, this paper carries out experimental analysis on the Young’s moduli and parallel-to-grain tensile strengths of cornstalk scrimber and glue-laminated cornstalk scrimber. The results show that the load-strain curve of glue-laminated cornstalk scrimber basically changed linearly parallel to grain, and the material exhibited stable Young’s modulus and good strength; the glue-laminated cornstalk scrimber had a slightly higher tensile strength than cornstalk scrimber, and could thus replace timber as a building material.

scholarly journals Influence of Partial Replacement of Micro-Silica by Fly-Ash on Strength Properties of Reactive Powder Concrete

2020 ◽  
Vol 9 (3) ◽  
pp. 2932-2937
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Reactive Powder Concrete ◽  
Experimental Investigations ◽  
Reactive Powder ◽  
Micro Silica

Reactive powder concrete (RPC) is the ultra-high strength concrete made by cementitious materials like silica fumes, cement etc. The coarse aggregates are completely replaced by quartz sand. Steel fibers which are optional are added to enhance the ductility. Market survey has shown that micro-silica is not so easily available and relatively costly. Therefore an attempt is made to experimentally investigate the reduction of micro-silica content by replacing it with fly-ash and mechanical properties of modified RPC are investigated. Experimental investigations show that compressive strength decreases gradually with addition of the fly ash. With 10 per cent replacement of micro silica, the flexural and tensile strength showed 40 and 46 per cent increase in the respective strength, though the decrease in the compressive strength was observed to be about 20 per cent. For further percentage of replacement, there was substantial drop in compressive, flexural as well as tensile strength. The experimental results thereby indicates that utilisation of fly-ash as a partial replacement to micro silica up to 10 per cent in RPC is feasible and shows quite acceptable mechanical performance with the advantage of utilisation of fly-ash in replacement of micro-silica.

Sign in / Sign up

Export Citation Format

Share Document