scholarly journals Short timescale wetting and penetration on porous sheets measured with ultrasound, direct absorption and contact angle

RSC Advances ◽  
2018 ◽  
Vol 8 (23) ◽  
pp. 12861-12869 ◽  
Author(s):  
Krainer Sarah ◽  
Hirn Ulrich
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Porous Media ◽  
Measurement Methods ◽  
Liquid Penetration ◽  
Direct Absorption ◽  
Short Timescale ◽  
Thin Porous Media

Liquid penetration and wetting on thin, porous media is studied using three different measurement methods, and using testing liquids with tailored viscosity, polarity and surface tension.

scholarly journals Influence of moisture content on the contact angle and surface tension measured on birch wood surfaces

2021 ◽  
Author(s):  
Rami Benkreif ◽  
Fatima Zohra Brahmia ◽  
Csilla Csiha
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Moisture Content ◽  
Solid Wood ◽  
Contact Angles ◽  
Surface Moisture ◽  
Wood Coatings ◽  
The Relationship ◽  
Wood Surfaces

AbstractSurface tension of solid wood surfaces affects the wettability and thus the adhesion of various adhesives and wood coatings. By measuring the contact angle of the wood, the surface tension can be calculated based on the Young-Dupré equation. Several publications have reported on contact angle measured with different test liquids, under different conditions. Results can only be compared if the test conditions are similar. While the roles of the drop volume, image shooting time etc., are widely recognized, the role of the wood surface moisture content (MC) is not evaluated in detail. In this study, the effect of wood moisture content on contact angle values, measured with distilled water and diiodomethane, on sanded birch (Betula pendula) surfaces was investigated, in order to find the relationship between them. With increasing MC from approximately 6% to 30%, increasing contact angle (decreasing surface tension) values were measured according to a logarithmic function. The function makes possible the calculation of contact angles that correspond to different MCs.

Increasing Storage Modulus, Contact Angle and Surface Tension of Airway Mucus Increases Clearance by Simulated Cough Through a Model Trachea

2010 ◽  
Author(s):  
Anpalaki J. Ragavan ◽  
Cahit A. Evrensel ◽  
Peter Krumpe
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Storage Modulus ◽  
Surface Properties ◽  
Respiratory Diseases ◽  
Interactive Effects ◽  
Altered Surface ◽  
Human Trachea ◽  
Tension Increase ◽  
And Storage

Altered surface and viscoelastic material properties of mucus during respiratory diseases have a strong influence on its clearance by cilia and cough. Combined effects of the surface properties (contact angle and surface tension) and storage modulus with relatively unchanged viscosity on displacement of the simulated mucus aliquot during simulated cough through a model adult human trachea is investigated. For the mucus simulants used in this study contact angle and surface tension increase significantly as storage modulus increase while viscosity remains practically unchanged. Displacement of mucus simulant aliquots increased significantly with increasing storage modulus (and contact angle) at a given cough velocity in the range between 5 meters/second (m/s) and 30 m/s with duration 0.3 s. Results suggest that the interactive effects of elasticity and surface properties may help facilitate mucus displacement at low cough velocities.

scholarly journals Experimental Investigation of Coal Dust Wettability Based on Surface Contact Angle

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Gang Zhou ◽  
Han Qiu ◽  
Qi Zhang ◽  
Mao Xu ◽  
Jiayuan Wang ◽  
...  
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Specific Surface ◽  
Coal Dust ◽  
Single Point ◽  
Contact Angles ◽  
Critical Surface ◽  
Volume Percentage ◽  
Surface Areas ◽  
Specific Surface Areas

Wettability is one of the key chemical properties of coal dust, which is very important to dedusting. In this paper, the theory of liquid wetting solid was presented firstly; then, taking the gas coal of Xinglongzhuang coal mine in China as an example, by determination of critical surface tension of coal piece, it can be concluded that only when the surface tension of surfactant solution is less than 45 mN/m can the coal sample be fully wetted. Due to the effect of particle dispersity, compared with the contact angle of milled coal particle, not all the contact angles of screened coal powder with different sizes have a tendency to increase. Furthermore, by the experiments of coal samples’ specific surface areas and porosities, it can be achieved that the volume of single-point total pore decreases with the gradual decreasing of coal’s porosity, while the ultramicropores’ dispersities and multipoint BET specific surface areas increase. Besides, by a series of contact angle experiments with different surfactants, it can be found that with the increasing of porosity and the decreasing of volume percentage of ultramicropore, the contact angle tends to reduce gradually and the coal dust is much easier to get wetted.

scholarly journals Effect of Pesticide Addition Sequence on the Preparation of Phytosanitary Spray Solutions

2019 ◽  
Vol 37 ◽  
Author(s):  
M.F.T. RAMOS ◽  
R.T.S. SANTOS ◽  
D.P. ALMEIDA ◽  
J.F.D. VECHIA ◽  
M.C. FERREIRA
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Propionic Acid ◽  
Biological Effect ◽  
Surface Coverage ◽  
Mineral Oil ◽  
Application Rate ◽  
Physicochemical Interactions ◽  
Effect Of Treatment ◽  
Droplet Method

ABSTRACT: The addition of adjuvants to herbicide solutions is aimed at preserving or enhancing the biological effect of treatment. However, it is commonly performed without knowledge of the physicochemical interactions between products. This study aimed to assess the effects of different addition sequences of the herbicide aminopyralid + fluroxypyr and adjuvants in the preparation of phytosanitary spray solutions on the surface tension and contact angle. Two experiments were carried out with herbicide doses of 1 and 2 L ha-1 associated with the adjuvants mineral oil (MO), silicone-polyether copolymer (SIL), and a mixture of phosphatidylcholine (lectin) and propionic acid (LEC), all at a proportion of 0.3% v v-1. The application rate was 150 L ha-1. Surface tension was measured by the pendant droplet method. Contact angle was measured on the adaxial and abaxial surfaces of leaves of the pasture weed Senna obtusifolia and parafilm. Preparation sequence did not change the contact angle on any of the analyzed surfaces at a dose of 1 L ha-1 of herbicide. For the dose of 2 L ha-1, the adjuvants SIL and LEC showed a higher spreading when previously added to the herbicide. MO resulted in a higher spreading when added after the herbicide, with higher surface coverage. Therefore, the preparation sequence influences the dispersion of phytosanitary spray solutions on targets.

Sign in / Sign up

Export Citation Format

Share Document