Hydrogen generation performance of novel Al–LiH–metal oxides

2018 ◽  
Vol 5 (7) ◽  
pp. 1700-1706 ◽  
Author(s):  
Peng Li ◽  
Fen Xu ◽  
Lixian Sun ◽  
Yongpeng Xia ◽  
Jun Chen ◽  
...  
Keyword(s):  
Hydrogen Production ◽  
Metal Oxide ◽  
Metal Oxides ◽  
Ball Milling ◽  
Hydrogen Generation ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Energy Ball ◽  
Oxide Composites

A series of novel hydrogen production materials, Al–LiH–metal oxide composites, have been prepared via high energy ball milling.

scholarly journals Microstructure refinement and physical properties of Ag-SnO2 based contact materials prepared by high-energy ball milling

2013 ◽  
Vol 45 (2) ◽  
pp. 173-180 ◽  
Author(s):  
V. Cosovic ◽  
M. Pavlovic ◽  
A. Cosovic ◽  
P. Vulic ◽  
M. Premovic ◽  
...  
Keyword(s):  
Metal Oxide ◽  
Physical Properties ◽  
Ball Milling ◽  
Electrical Contact ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Powder Metallurgy Method ◽  
Contact Materials ◽  
Energy Ball ◽  
Electrical Contact Materials

High energy ball milling was used in order to improve dispersion of metal oxide in Ag-SnO2 electrical contact materials. The processed Ag-SnO2 (92:8) and Ag-SnO2In2O3 (87.8:9.30:2.9) powder mixtures were subsequently consolidated to bulk solid pieces by conventional powder metallurgy method. The characterization of the prepared samples included microstructural analysis by XRD and SEM, as well as measurements of physical properties such as density, hardness and electrical conductivity. The results of X-Ray analysis point to reduction of crystallite size after milling of about ten times. Microstructures of sintered Ag-SnO2 and Ag-SnO2 In2O3 materials display very fine dispersion of the oxide components in silver matrix. Somewhat higher uniformity was obtained for Ag-SnO2 In2O3 material which was illustrated by results of SEM analysis and more consistent microhardness values. The obtained values of studied physical properties were found to be in accordance with observed higher dispersion of metal oxide particles and comparable to properties of commercial electrical contact materials of this type.

scholarly journals Impact Evaluation of High Energy Ball Milling Homogenization Process in the Phase Distribution of Hydroxyapatite-Barium Titanate Plasma Spray Biocoating

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 728
Author(s):  
Roberto Gómez Batres ◽  
Zelma S. Guzmán Escobedo ◽  
Karime Carrera Gutiérrez ◽  
Irene Leal Berumen ◽  
Abel Hurtado Macias ◽  
...  
Keyword(s):  
Barium Titanate ◽  
Ball Milling ◽  
Plasma Spray ◽  
Bonding Strength ◽  
Phase Distribution ◽  
High Energy ◽  
High Energy Ball Milling ◽  
X Ray ◽  
Nanomechanical Properties ◽  
Energy Ball

Air plasma spray technique (APS) is widely used in the biomedical industry for the development of HA-based biocoatings. The present study focuses on the influence of powder homogenization treatment by high-energy ball milling (HEBM) in developing a novel hydroxyapatite-barium titanate (HA/BT) composite coating deposited by APS; in order to compare the impact of the milling process, powders were homogenized by mechanical stirring homogenization (MSH) too. For the two-homogenization process, three weight percent ratios were studied; 10%, 30%, and 50% w/w of BT in the HA matrix. The phase and crystallite size were analyzed by X-ray diffraction patterns (XRD); the BT-phase distribution in the coating was analyzed by backscattered electron image (BSE) with a scanning electron microscope (SEM); the energy-dispersive X-ray spectroscopy (EDS) analysis was used to determinate the Ca/P molar ratio of the coatings, the degree of adhesion (bonding strength) of coatings was determinate by pull-out test according to ASTM C633, and finally the nanomechanical properties was determinate by nanoindentation. In the results, the HEBM powder processing shows better efficiency in phase distribution, being the 30% (w/w) of BT in HA matrix that promotes the best bonding strength performance and failure type conduct (cohesive-type), on the other hand HEBM powder treatment promotes a slightly greater crystal phase stability and crystal shrank conduct against MSH; the HEBM promotes a better behavior in the nanomechanical properties of (i) adhesive strength, (ii) cohesive/adhesive failure-type, (iii) stiffness, (iv) elastic modulus, and (v) hardness properties.

scholarly journals Effect of the route and sintering time in the microstructure of pure aluminum prepared by high energy ball milling

2021 ◽  
Vol 27 (S1) ◽  
pp. 3294-3296
Author(s):  
José Mendoza ◽  
C. Carreño-Gallardo ◽  
I. Estrada-Guel ◽  
C.G. Garay-Reyes ◽  
M.A. Ruiz-Esparza-Rodriguez ◽  
...  
Keyword(s):  
Ball Milling ◽  
Pure Aluminum ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Sintering Time ◽  
Energy Ball

Atomic structure, magnetism, and transport properties of damaged La0.67Ca0.33MnO3−δ processed via high-energy ball milling

1999 ◽  
Vol 86 (3) ◽  
pp. 1607-1610 ◽  
Author(s):  
Michael B. Liou ◽  
Shaheen Islam ◽  
D. J. Fatemi ◽  
V. M. Browning ◽  
D. J. Gillespie ◽  
...  
Keyword(s):  
Transport Properties ◽  
Ball Milling ◽  
Atomic Structure ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Energy Ball

scholarly journals Magnetic properties and crystal structure of elemental cobalt powder modified by high-energy ball milling

2019 ◽  
Vol 8 (5) ◽  
pp. 4995-5003 ◽  
Author(s):  
J.A. Betancourt-Cantera ◽  
F. Sánchez-De Jesús ◽  
A.M. Bolarín-Miró ◽  
G. Torres-Villaseñor ◽  
L.G. Betancourt-Cantera
Keyword(s):  
Crystal Structure ◽  
Magnetic Properties ◽  
Ball Milling ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Cobalt Powder ◽  
Energy Ball
Sign in / Sign up

Export Citation Format

Share Document