scholarly journals Mechanisms behind the enhancement of thermal properties of graphene nanofluids

Nanoscale ◽  
2018 ◽  
Vol 10 (32) ◽  
pp. 15402-15409 ◽  
Author(s):  
M. R. Rodríguez-Laguna ◽  
A. Castro-Alvarez ◽  
M. Sledzinska ◽  
J. Maire ◽  
F. Costanzo ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Specific Heat ◽  
Specific Heat Capacity

While the dispersion of nanomaterials is known to be effective in enhancing the thermal conductivity and specific heat capacity of fluids, the mechanisms behind this enhancement remain to be elucidated.

Determination of the Thermal Properties of a PCB by Coupled Numerical and Experimental Approach

2020 ◽  
Author(s):  
Yener Usul ◽  
Mustafa Özçatalbaş
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Numerical Analysis ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Thermal Analyses ◽  
Analysis Model ◽  
Linear Temperature ◽  
Coefficient Of Thermal Conductivity

Abstract Increasing demand for usage of electronics intensely in narrow enclosures necessitates accurate thermal analyses to be performed. Conduction based FEM (Finite Element Method) is a common and practical way to examine the thermal behavior of an electronic system. First step to perform a numerical analysis for any system is to set up the correct analysis model. In this paper, a method for obtaining the coefficient of thermal conductivity and specific heat capacity of a PCB which has generally a complex composite layup structure composed of conductive layers, and dielectric layers. In the study, above mentioned properties are obtained performing a simple nondestructive experiment and a numerical analysis. In the method, a small portion of PCB is sandwiched from one side at certain pressure by jaws. A couple of linear temperature profiles are applied to the jaws successively. Unknown values are tuned in the analysis model until the results of FEM analysis and experiment match. The values for the coefficient of thermal conductivity and specific heat capacity which the experiment and numerical analysis results match can be said to be the actual values. From this point on, the PCB whose thermal properties are determined can be analyzed numerically for any desired geometry and boundary condition.

Influence of Mesocarp Fibre Inclusion on Thermal Properties of Foamed Concrete

2021 ◽  
Vol 87 (1) ◽  
pp. 1-11
Author(s):  
Siti Shahirah Suhaili ◽  
Md Azree Othuman Mydin ◽  
Hanizam Awang
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Volume Fraction ◽  
Thermal Constant ◽  
Volume Fractions ◽  
Foamed Concrete

The addition of mesocarp fibre as a bio-composite material in foamed concrete can be well used in building components to provide energy efficiency in the buildings if the fibre could also offer excellent thermal properties to the foamed concrete. It has practical significance as making it a suitable material for building that can reduce heat gain through the envelope into the building thus improved the internal thermal comfort. Hence, the aim of the present study is to investigate the influence of different volume fractions of mesocarp fibre on thermal properties of foamed concrete. The mesocarp fibre was prepared with 10, 20, 30, 40, 50 and 60% by volume fraction and then incorporated into the 600, 1200 and 1800 kg/m3 density of foamed concrete with constant cement-sand ratio of 1:1.5 and water-cement ratio of 0.45. Hot disk thermal constant analyser was used to attain the thermal conductivity, thermal diffusivity and specific heat capacity of foamed concrete of various volume fractions and densities. From the experimental results, it had shown that addition of mesocarp fibre of 10-40% by volume fraction resulting in low thermal conductivity and specific heat capacity and high the thermal diffusivity of foamed concrete with 600 and 1800 kg/m3 density compared to the control mix while the optimum amount of mesocarp fibre only limit up to 30% by volume fraction for 1200 kg/m3 density compared to control mix. The results demonstrated a very high correlation between thermal conductivity, thermal diffusivity and specific heat capacity which R2 value more than 90%.

Thermal Properties of Selected Timbers

2014 ◽  
Vol 982 ◽  
pp. 100-103 ◽  
Author(s):  
Dana Koňáková ◽  
Monika Čáchová ◽  
Eva Vejmelková ◽  
Martin Keppert ◽  
Robert Černý
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Moisture Content ◽  
Specific Heat ◽  
Heat Transport ◽  
Specific Heat Capacity ◽  
Open Porosity ◽  
Building Structures ◽  
The Difference

This article deals with thermal properties of selected kinds of timber. Wood, generally, is one of often used natural materials in building structures. For our research, woods were selected according to frequency of utilization in civil engineering branch. Four different timbers were chosen, and experimental determinations of their properties were performed. Basic physical properties as well as thermal properties belong among studied characteristics. From achieved results, it is obvious, that the bulk density of studied wood ranges between 373 kg m-3 and 649 kg m-3, the open porosity differ by 13%. Regarding thermal properties, values of the thermal conductivity as well as the specific heat capacity are influenced mainly by the open porosity and moisture content. The thermal conductivity in dry state varies by about 31% while in the case of the specific heat capacity the difference is about 19%. Obtained date will be used in the mathematical analysis of heat transport in building structures.

scholarly journals Effectiveness of Thermal Properties in Thermal Energy Storage Modeling

2021 ◽  
Vol 7 ◽  
Author(s):  
Law Torres Sevilla ◽  
Jovana Radulovic
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Energy Storage ◽  
Specific Heat ◽  
Melting Temperature ◽  
Latent Heat ◽  
Specific Heat Capacity ◽  
Thermal Energy ◽  
Thermal Energy Storage

This paper studies the influence of material thermal properties on the charging dynamics in a low temperature Thermal Energy Storage, which combines sensible and latent heat. The analysis is based on a small scale packed bed with encapsulated PCMs, numerically solved using COMSOL Multiphysics. The PCMs studied are materials constructed based on typical thermal properties (melting temperature, density, specific heat capacity (solid and liquid), thermal conductivity (solid and liquid) and the latent heat) of storage mediums in literature. The range of values are: 25–65°C for the melting temperature, 10–500 kJ/kg for the latent heat, 600–1,000 kg/m3 for the density, 0.1–0.4 W/mK (solid and liquid) for the thermal conductivity and 1,000–2,200 J/kgK (solid and liquid) for the specific heat capacity. The temperature change is monitored at three different positions along the tank. The system consists of a 2D tank with L/D ratio of 1 at a starting temperature of 20°C. Water, as the heat transfer fluid, enters the tank at 90°C. Results indicate that latent heat is a leading parameter in the performance of the system, and that the thermal properties of the PCM in liquid phase influence the overall heat absorption more than its solid counterpart.

scholarly journals Thermal Behaviour of Hybrid Composites Reinforced with Natural Fibers and Kevlar

2019 ◽  
Vol 8 (2) ◽  
pp. 5616-5621
Keyword(s):  
Thermal Conductivity ◽  
Thermal Stability ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Degradation ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Synthetic Fiber

There is a wide scope to develop suitable hybrid combination for making Fiber Reinforced Polymer (FRP) to utilize the properties of both natural and synthetic fibers. Economic and environmental reasons justify the use of natural fiber in place of synthetic fiber composite. Thermal stability is one of the important properties for the FRP panel in the applications such as structural panels/roof panels, cold storage and air conditioned ducts of building. The aim of this paper is to investigate thermal properties of hybrid FRP made of Jute, Flax, Sisal and Hemp in combination with kevlar-29. Composite wall conductivity measurement, DSC/TGA technique are used to study thermal conductivity, thermal stability, change in specific heat capacity, thermal degradation. All the panels showed lower thermal conductivity of less than 1 W/m 0C; however the flax and hemp panels had lowest thermal conductivity of around 0.45 W/m0C. DSC thermographs indicated broad exotherm and major changes in specific heat capacity at 200 0C for all panels. In addition, TGA technique showed main weight loss around 30%-51% of panels around 210 0C. Thus the thermal properties of all panels were stable till 200 0C. Thermogravimetric analysis of F- FRP shows thermal stability at lower range of temperature while in H- FRP thermal degradation occurs in two steps around 260 0C and 410 0C with the wt. loss of 53.72% and 26.79% respectively

scholarly journals On the Use of Thermal Properties for Characterizing Dimension Stones

2013 ◽  
Vol 548 ◽  
pp. 231-238 ◽  
Author(s):  
Paulo Amaral ◽  
António Correia ◽  
Luís Lopes ◽  
Paula Rebola ◽  
António Pinho ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Heat Production ◽  
Civil Engineering ◽  
Chemical Properties ◽  
Usual Practice

The use of dimension stones in architecture and civil engineering implies the knowledge of several mechanical, physical, and chemical properties. Even though it has been usual practice to measure physical and mechanical properties of dimension stones the same is not true for thermal properties such as thermal conductivity, thermal diffusivity, specific heat capacity, and heat production. These properties are particularly important when processes related with heating and cooling of buildings must be considered. Thermal conductivity, thermal diffusivity, and specific heat capacity are related with the way thermal energy is transmitted and accumulated in stones; heat production has to do with the amount of radioactive elements in the rocks and so with the environmental impact of radioactivity and public health problems. It is important to start to measure on a routine basis those four thermal properties in rocks and, in particular, in dimension rocks so that their application can be improved and optimized. With this is mind three sets of different rock types (granites, limestones, and marbles) were collected to measure the thermal conductivity, the thermal diffusivity, and the specific heat capacity with the objective of characterizing them in terms of those properties. Since the same set of rocks has also been studied for other physical properties, a correlation amongst all the measured properties is attempted. For each rock type several samples were used to measure the thermal conductivity, the thermal diffusivity, and the specific heat capacity, and average values were obtained and are presented. As an example, for granites the thermal conductivity varies between 2.87 and 3.75 W/mK; for limestones varies between 2.82 and 3.17 W/mK; and for marbles varies between 2.86 and 3.02 W/mK. It is hoped that measuring thermal properties on dimension stones will help to better adequate them to their use in civil engineering as well as to adequate their use in terms of a CE product.

scholarly journals Effect of cooking time on the physical, chemical and thermal properties of acha seeds

2017 ◽  
Vol 6 (2) ◽  
Author(s):  
Akeem O. Raji ◽  
Hajarat O. Nassam ◽  
Tawakalitu E. Aruna ◽  
Monsurat O. Raji ◽  
Maimuna Sani
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Aspect Ratio ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Cooking Time ◽  
Crude Fibre ◽  
Cereal Grain

Acha is a less utilized cereal grain in Africa. Scaling up of the processing technology of acha seeds is desirable if accurate information on effect of processing on its properties is available. This study investigated the effect of cooking duration on the chemical and physical properties of acha seeds. Cooking times (2.5, 5, 7.5 and 10 minutes) at 100oC were used. The volume, length, breadth, thickness, porosity, density, sphericity, aspect ratio, specific heat capacity, thermal conductivity, thermal diffusivity, moisture, protein, fat, ash, crude fibre and carbohydrate were determined using standard methods. Data were analysed using ANOVA at p = 0.05. The results obtained revealed that varietal difference had a significant effect on volume, length, breadth, thickness, true density, bulk density, porosity, sphericity and aspect ratio. The moisture content, ash, protein, crude fibre, fat, carbohydrate, specific heat capacity, thermal conductivity and thermal diffusivity varied from 8.80 - 56.17 %, 0.32 - 1.87%, 1.92 - 11.50%, 0.29 - 1.58%, 0.32 - 2.81%, 40.94 - 76.26%, 1.66 -2.97 kJkg-1K-1, 0.26 -0.43 Wm-1K-1 and 0.85 x 10-7 - 1.17 x 10-7 ms-2 respectively, as significantly influenced by cooking time. Cooking for 7.5 minutes was appropriate using the moisture uptakes and thermal properties as criteria. 

scholarly journals Thermal Properties of Polyester/Epoxy Blend

2021 ◽  
pp. 1128-1134
Author(s):  
Aqeel Mohsin Ali ◽  
Mohammed A. Jaber ◽  
Nooraldeen A. Toama
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Unsaturated Polyester ◽  
Weight Fraction ◽  
Peak Shift ◽  
Cross Linking ◽  
Epoxy Matrices

Unsaturated polyester toughened Epoxy was developed. Epoxy resin had toughened by weight fraction of 10, 20, 30, and 40 wt. % unsaturated polyester. FTIR spectroscopy has been used to investigating the intermolecular hydrogen bonding. Unsaturated polyester–epoxy matrices were characterized for their thermal properties. The FTIR test detected a peak shift of the functional groups which can explain cross-linking occurs between the two resins. The crosslinking between epoxy and unsaturated polyester confirmed via the existence of the stretching asymmetrical C-C band and contraction of the  C-O band. The DSC test demonstrated that glass transition temperature value decreases with epoxy strengthening. The specific heat capacity and thermal conductivity have been affected the unsaturated polyester percentage. Thermal conductivity, specific heat capacity and thermal effuisivity increased by weight fraction of polyester. The thermal diffusivity values of blends showed a little decreasing.

scholarly journals Thermal properties of soursop seeds and kernels

2017 ◽  
Vol 63 (No. 2) ◽  
pp. 79-85 ◽  
Author(s):  
Tunji Oloyede Christopher ◽  
Bukola Akande Fatai ◽  
Olaniyi Oriola Kazeem ◽  
Oluwatoyin Oniya Oluwole
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Thermal Diffusivity ◽  
Moisture Content ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Oil Recovery ◽  
Thermal Analyser ◽  
Selection Of

The thermal properties of soursop seeds and kernels were determined as a function of moisture content, ranged from 8.0 to 32.5% (d.b.). Three primary thermal properties: specific heat capacity, thermal conductivity and thermal diffusivity were determined using Dual-Needle SH-1 sensors in KD2-PRO thermal analyser. The obtained results shown that specific heat capacity of seeds and kernels increased linearly from 768 to 2,131 J/kg/K and from 1,137 to 1,438 J/kg/K, respectively. Seed thermal conductivity increased linearly from 0.075 to 0.550 W/m/K while it increased polynomially from 0.153 to 0.245 W/m/K for kernel. Thermal diffusivity of both seeds and kernels increased linearly from 0.119 to 0.262 m<sup>2</sup>/s and 0.120 to 0.256 m<sup>2</sup>/s, respectively. Analysis of variance results showed that the moisture content has a significant effect on thermal properties (p ≤ 0.05). These values indicated the ability of the material to retain heat which enhances oil recovery and can be used in the design of machine and selection of suitable methods for their handling and processing.

New borehole heat exchanger thermal enhanced grout formulations

2021 ◽  
Author(s):  
Eloisa Di Sipio ◽  
Enrico Garbin ◽  
Laura Fedele ◽  
Davide Menegazzo ◽  
Ludovico Mascarin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Properties ◽  
Heat Exchange ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Operation Mode ◽  
Silica Sand ◽  
Geothermal Systems

&lt;p&gt;In shallow geothermal systems, especially ground source heat pumps (GSHP), cementitious grouts play a decisive role in guaranteeing an efficient heat transfer between the probe and the surrounding ground. Several studies have been devoted to understand the effect of different additives (silica sand, graphite, fluorspar, glass and fly ash &amp;#8230;) in improving especially the thermal conductivity of such mixtures, maintaining at the same time physical properties as viscosity and workability suitable for in situ application. In fact, when continuous operation mode is running, thermal conductivity shows a positive effect on the mean heat exchange rate of vertical borehole heat exchangers (BHE). However, when an intermittent operation mode is selected, the BHE performance improves when a high thermal conductivity is coupled with a high specific heat capacity.&lt;/p&gt;&lt;p&gt;This research focus on assessing the contribution of two specific thermal additives (silica sand and molybdenum disulphide powder) to the thermal properties&amp;#8217; improvements of a specific commercial cementitious grout. These components are added in different proportion to the grout, up to the creation of 6 different mixtures. For each mixture 3 specimens are prepared, in order to perform the thermo-physical analyses. In addition, other 3 commercial grouts are considered. A total of 10 mixtures, leading to the creation of 30 specimens, have been analyzed. Then, thermal conductivity, thermal diffusivity and specific heat capacity of each specimen measured in anhydrous and saturated conditions are considered.&lt;/p&gt;&lt;p&gt;The commercial grouts prepared as stated by the producers show, as expected, a minimum variation of their thermal properties in wet and anhydrous conditions. Instead, when the additives are used, a noticeable improvement of the thermal properties is observed in saturated conditions, where the effect of silica sand seems dominant. The best thermal properties improvement obtained by combining the two additives is also considered.&lt;/p&gt;&lt;p&gt;However, the grouts suitability to be easily managed on site must be considered because, even if the new mixtures show a general gain of the thermal properties, these can be difficult to apply going from laboratory to full scale.&lt;/p&gt;&lt;p&gt;Anyway, the characterization of the grouts thermal properties based on composition and saturation variations is important not only in numerical simulations, but also in analytical approaches, typical of the heat exchange probe fields sizing processes. In fact, the cementitious grouts play a key role in determining the shallow geothermal systems efficiency in transient mode operation, often neglected by sizing programs. In fact, those characterized by better thermal performances will contribute to the reduction of the borehole thermal resistances, interposed in the heat exchange processes between the heat transfer fluid and the ground. Finally, this research contributes to fill the gap between numerical simulation and experimental data, providing real data to be used as database for further numerical modelling analysis improvement.&lt;/p&gt;&lt;p&gt;&amp;#160;&lt;/p&gt;&lt;p&gt;GEO4CIVHIC project has received funding from the European Union&amp;#8217;s Horizon 2020 research and innovation program under grant agreement No. 792355.&lt;/p&gt;

Sign in / Sign up

Export Citation Format

Share Document