Thermoelectric performance enhancement of Cu2S by Se doping leading to a simultaneous power factor increase and thermal conductivity reduction

2017 ◽  
Vol 5 (31) ◽  
pp. 7845-7852 ◽  
Author(s):  
Yao Yao ◽  
Bo-Ping Zhang ◽  
Jun Pei ◽  
Yao-Chun Liu ◽  
Jing-Feng Li
Keyword(s):  
Thermal Conductivity ◽  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Power Factor ◽  
Performance Enhancement ◽  
Thermoelectric Performance ◽  
Plasma Sintering ◽  
Se Doping ◽  
Spark Plasma

A series of single-phased Cu2S1−xSex bulks were prepared by using mechanical alloying (MA) combined with spark plasma sintering (SPS). Our results suggest that the TE properties of Cu2S can be greatly enhanced by simultaneously increasing PF and decreasing κ via doping a sole Se element.

Bi2Te3 and Bi2Te3/Nano-SiC Prepared by Mechanical Alloying and Spark Plasma Sintering

2007 ◽  
Vol 280-283 ◽  
pp. 397-400 ◽  
Author(s):  
Jing Liu ◽  
Jing Feng Li
Keyword(s):  
Thermal Conductivity ◽  
Electrical Resistivity ◽  
Mechanical Alloying ◽  
Seebeck Coefficient ◽  
Spark Plasma Sintering ◽  
Thermoelectric Materials ◽  
Room Temperature ◽  
Mechanically Alloyed ◽  
Plasma Sintering ◽  
Spark Plasma

Bi2Te3-based alloys are currently best-known, technological thermoelectric materials near room temperature. In this paper, Bi2Te3 and nano-SiC dispersed Bi2Te3 were prepared by mechanical alloying followed by spark plasma sintering (SPS). Raw powders of Bi, Te and SiC were mixed and mechanically alloyed in an argon atmosphere using a planetary ball mill. The SPS temperature was 623K, and the holding time was 5 minutes. The samples were characterized by X-ray Diffraction (XRD) and Scanning electron Microscope (SEM). The thermoelectric properties: i.e. Seebeck coefficient, electrical resistivity and thermal conductivity were measured at temperatures from room temperature to 573K, followed by the evaluation of figure of merit. The results revealed that the SiC dispersion in the Bi2Te3 matrix increased Seebeck coefficient. Although the electrical resistivity was increased somewhat, the thermal conductivity was reduced by the SiC dispersion, indicating that promising thermoelectric materials with enhanced mechanical properties may be obtained in the nano-SiC dispersed Bi2Te3 composites with optimal compositions.

Densification and Thermal Conductivity of Y2O3-Doped AlN Ceramics by Spark Plasma Sintering

2007 ◽  
Vol 352 ◽  
pp. 227-231 ◽  
Author(s):  
Qiang Shen ◽  
Z.D. Wei ◽  
Mei Juan Li ◽  
Lian Meng Zhang
Keyword(s):  
Thermal Conductivity ◽  
Grain Boundaries ◽  
Spark Plasma Sintering ◽  
Particle Surface ◽  
Boundary Phase ◽  
Homogeneous Microstructure ◽  
Densification Mechanism ◽  
Sintering Additive ◽  
Plasma Sintering ◽  
Spark Plasma

AlN ceramics doped with yttrium oxide (Y2O3) as the sintering additive were prepared via the spark plasma sintering (SPS) technique. The sintering behaviors and densification mechanism were mainly investigated. The results showed that Y2O3 addition could promote the AlN densification. Y2O3-doped AlN samples could be densified at low temperatures of 1600-1700oC in 20-25 minutes. The AlN samples were characterized with homogeneous microstructure. The Y-Al-O compounds were created on the grain boundaries due to the reactions between Y2O3 and Al2O3 on AlN particle surface. With increasing the sintering temperature, AlN grains grew up, and the location of grain boundaries as well as the phase compositions changed. The Y/Al ratio in the aluminates increased, from Y3Al5O12 to YAlO3 and to Y4Al2O9. High-density, the growth of AlN grains and the homogenous dispersion of boundary phase were helpful to improve the thermal conductivity of AlN ceramics. The thermal conductivity of 122Wm-1K-1 for the 4.0 mass%Y2O3-doped AlN sample was reached.

scholarly journals Macroscopic weavable fibers of carbon nanotubes with giant thermoelectric power factor

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Natsumi Komatsu ◽  
Yota Ichinose ◽  
Oliver S. Dewey ◽  
Lauren W. Taylor ◽  
Mitchell A. Trafford ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Thermoelectric Power ◽  
Power Factor ◽  
Fermi Energy ◽  
Performance Enhancement ◽  
Thermoelectric Performance ◽  
Thermoelectric Power Factor ◽  
Large Power ◽  
Energy Tuning

AbstractLow-dimensional materials have recently attracted much interest as thermoelectric materials because of their charge carrier confinement leading to thermoelectric performance enhancement. Carbon nanotubes are promising candidates because of their one-dimensionality in addition to their unique advantages such as flexibility and light weight. However, preserving the large power factor of individual carbon nanotubes in macroscopic assemblies has been challenging, primarily due to poor sample morphology and a lack of proper Fermi energy tuning. Here, we report an ultrahigh value of power factor (14 ± 5 mW m−1 K−2) for macroscopic weavable fibers of aligned carbon nanotubes with ultrahigh electrical and thermal conductivity. The observed giant power factor originates from the ultrahigh electrical conductivity achieved through excellent sample morphology, combined with an enhanced Seebeck coefficient through Fermi energy tuning. We fabricate a textile thermoelectric generator based on these carbon nanotube fibers, which demonstrates high thermoelectric performance, weavability, and scalability. The giant power factor we observe make these fibers strong candidates for the emerging field of thermoelectric active cooling, which requires a large thermoelectric power factor and a large thermal conductivity at the same time.

Sign in / Sign up

Export Citation Format

Share Document