scholarly journals Selective metallic coating of 3D-printed microstructures on flexible substrates

RSC Advances ◽  
2017 ◽  
Vol 7 (81) ◽  
pp. 51663-51669 ◽  
Author(s):  
Kuan-Ming Huang ◽  
Shang-Chen Tsai ◽  
Yu-Kuan Lee ◽  
Cheng-Kai Yuan ◽  
Yu-Ching Chang ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Metallic Coating ◽  
Flexible Substrates ◽  
Pdms Substrate ◽  
Simple Method ◽  
3D Printed

In this work, a simple method was developed to fabricate micron scale three-dimensional (3D) conductive objects on a flexible PDMS substrate.

Use of Three-dimensional Printing in the Development of Optimal Cardiac CT Scanning Protocols

2020 ◽  
Vol 16 (8) ◽  
pp. 967-977
Author(s):  
Zhonghua Sun
Keyword(s):  
Cardiovascular Disease ◽  
Cardiac Computed Tomography ◽  
Three Dimensional ◽  
Ct Scanning ◽  
Aortic Diseases ◽  
Clinical Value ◽  
Three Dimensional Printing ◽  
Doctor Patient Communication ◽  
Medical Education And Training ◽  
3D Printed

Three-dimensional (3D) printing is increasingly used in medical applications with most of the studies focusing on its applications in medical education and training, pre-surgical planning and simulation, and doctor-patient communication. An emerging area of utilising 3D printed models lies in the development of cardiac computed tomography (CT) protocols for visualisation and detection of cardiovascular disease. Specifically, 3D printed heart and cardiovascular models have shown potential value in the evaluation of coronary plaques and coronary stents, aortic diseases and detection of pulmonary embolism. This review article provides an overview of the clinical value of 3D printed models in these areas with regard to the development of optimal CT scanning protocols for both diagnostic evaluation of cardiovascular disease and reduction of radiation dose. The expected outcomes are to encourage further research towards this direction.

Investigation of the Static Behavior and Failure Mechanisms of a 3D Printed Bio-Based Sandwich with Auxetic Core

2020 ◽  
Vol 12 (05) ◽  
pp. 2050051
Author(s):  
Khawla Essassi ◽  
Jean-Luc Rebiere ◽  
Abderrahim El Mahi ◽  
Mohamed Amine Ben Souf ◽  
Anas Bouguecha ◽  
...  
Keyword(s):  
Failure Mechanisms ◽  
Three Dimensional ◽  
Acoustic Emissions ◽  
Shear Stiffness ◽  
Tensile Tests ◽  
Sandwich Composite ◽  
Static Behavior ◽  
Flax Fibers ◽  
Data Points ◽  
3D Printed

In this research contribution, the static behavior and failure mechanisms are developed for a three-dimensional (3D) printed dogbone, auxetic structure and sandwich composite using acoustic emissions (AEs). The skins, core and whole sandwich are manufactured using the same bio-based material which is polylactic acid reinforced with micro-flax fibers. Tensile tests are conducted on the skins and the core while bending tests are conducted on the sandwich composite. Those tests are carried out on four different auxetic densities in order to investigate their effect on the mechanical and damage properties of the materials. To monitor the invisible damage and damage propagation, a highly sensitive AE testing method is used. It is found that the sandwich with high core density displays advanced mechanical properties in terms of bending stiffness, shear stiffness, facing bending stress and core shear stress. In addition, the AE data points during testing present an amplitude range of 40–85[Formula: see text]dB that characterizes visible and invisible damage up to failure.

scholarly journals Fabrication of Eutectic Ga-In Nanowire Arrays Based on Plateau–Rayleigh Instability

Molecules ◽  
2021 ◽  
Vol 26 (15) ◽  
pp. 4616
Author(s):  
Takashi Ikuno ◽  
Zen Somei
Keyword(s):  
Integrated Circuits ◽  
Substrate Surface ◽  
Three Dimensional ◽  
Average Diameter ◽  
Nanowire Arrays ◽  
Scanning Probe ◽  
Rayleigh Instability ◽  
Simple Method ◽  
Flat Substrate ◽  
Metal Nanowire

We have developed a simple method of fabricating liquid metal nanowire (NW) arrays of eutectic GaIn (EGaIn). When an EGaIn droplet anchored on a flat substrate is pulled perpendicular to the substrate surface at room temperature, an hourglass shaped EGaIn is formed. At the neck of the shape, based on the Plateau–Rayleigh instability, the EGaIn bridge with periodically varying thicknesses is formed. Finally, the bridge is broken down by additional pulling. Then, EGaIn NW is formed at the surface of the breakpoint. In addition, EGaIn NW arrays are found to be fabricated by pulling multiple EGaIn droplets on a substrate simultaneously. The average diameter of the obtained NW was approximately 0.6 μm and the length of the NW depended on the amount of droplet anchored on the substrate. The EGaIn NWs fabricated in this study may be used for three-dimensional wiring for integrated circuits, the tips of scanning probe microscopes, and field electron emission arrays.

scholarly journals Midface Reconstruction: Planning and Outcome

2020 ◽  
Vol 53 (03) ◽  
pp. 324-334
Author(s):  
Gautam Biswas
Keyword(s):  
Digital Imaging ◽  
3D Structure ◽  
Three Dimensional ◽  
The Past ◽  
Complex Anatomy ◽  
Osseointegrated Implants ◽  
Low Profile ◽  
3D Printed ◽  
Midface Reconstruction ◽  
Reconstruction Planning

Abstract Reconstruction of the complex anatomy and aesthetics of the midface is often a challenge. A careful understanding of this three-dimensional (3D) structure is necessary. Anticipating the extent of excision and its planning following oncological resections is critical.In the past over two decades, with the advances in microsurgical procedures, contributions toward the reconstruction of this area have generated interest. Planning using digital imaging, 3D printed models, osseointegrated implants, and low-profile plates, has favorably impacted the outcome. However, there are still controversies in the management: to use single composite tissues versus multiple tissues; implants versus autografts; vascularized versus nonvascularized bone; prosthesis versus reconstruction.This article explores the present available options in maxillary reconstruction and outlines the approach in the management garnered from past publications and experiences.

scholarly journals Recurrent contracted sockets treated with personalized, three-dimensionally printed conformers and buccal grafts

2021 ◽  
pp. 112067212110000
Author(s):  
Annabel LW Groot ◽  
Jelmer S Remmers ◽  
Roel JHM Kloos ◽  
Peerooz Saeed ◽  
Dyonne T Hartong
Keyword(s):  
Three Dimensional ◽  
Case Series ◽  
Secondary Outcome ◽  
Retrospective Case ◽  
Upper Eyelid ◽  
Ocular Prosthesis ◽  
Buccal Mucosal Graft ◽  
Custom Made ◽  
3D Printed

Purpose: Recurrent contracted sockets are complex situations where previous surgeries have failed, disabling the wear of an ocular prosthesis. A combined method of surgery and long-term fixation using custom-made, three-dimensional (3D) printed conformers is evaluated. Methods: Retrospective case series of nine patients with recurrent excessive socket contraction and inability to wear a prosthesis, caused by chemical burns ( n = 3), fireworks ( n = 3), trauma ( n = 2) and enucleation and radiotherapy at childhood due to optic nerve glioma ( n = 1) with three average previous socket surgeries (range 2–6). Treatment consisted of a buccal mucosal graft and personalized 3D-printed conformer designed to be fixated to the periosteum and tarsal plates for minimal 2 months. Primary outcome was the retention of an ocular prosthesis. Secondary outcome was the need for additional surgeries. Results: Outcomes were measured at final follow-up between 7 and 36 months postoperatively (mean 20 months). Eight cases were able to wear an ocular prosthesis after 2 months. Three cases initially treated for only the upper or only the lower fornix needed subsequent surgery for the opposite fornix for functional reasons. Two cases had later surgery for cosmetic improvement of upper eyelid position. Despite pre-existing lid abnormalities (scar, entropion, lash deficiency), cosmetic outcome was judged highly acceptable in six cases because of symmetric contour and volume, and reasonably acceptable in the remaining two. Conclusions: Buccal mucosal transplant fixated with a personalized 3D-designed conformer enables retention of a well-fitted ocular prosthesis in previously failed socket surgeries. Initial treatment of both upper and lower fornices is recommended to avoid subsequent surgeries for functional reasons.

scholarly journals Three-dimensional printing for heart diseases: clinical application review

2021 ◽  
Author(s):  
Yanyan Ma ◽  
Peng Ding ◽  
Lanlan Li ◽  
Yang Liu ◽  
Ping Jin ◽  
...  
Keyword(s):  
3D Printing ◽  
Clinical Application ◽  
Heart Diseases ◽  
Three Dimensional ◽  
Convincing Evidence ◽  
Surgical Interventions ◽  
Three Dimensional Printing ◽  
Complex Anatomy ◽  
Precise Understanding ◽  
3D Printed

AbstractHeart diseases remain the top threat to human health, and the treatment of heart diseases changes with each passing day. Convincing evidence shows that three-dimensional (3D) printing allows for a more precise understanding of the complex anatomy associated with various heart diseases. In addition, 3D-printed models of cardiac diseases may serve as effective educational tools and for hands-on simulation of surgical interventions. We introduce examples of the clinical applications of different types of 3D printing based on specific cases and clinical application scenarios of 3D printing in treating heart diseases. We also discuss the limitations and clinically unmet needs of 3D printing in this context.

scholarly journals Two-Dimensional Visualization of the Three-Dimensional Planned Sacroiliac Screw Corridor with the Slice Fusion Method

2021 ◽  
Vol 10 (2) ◽  
pp. 184
Author(s):  
Maximilian Kerschbaum ◽  
Siegmund Lang ◽  
Florian Baumann ◽  
Volker Alt ◽  
Michael Worlicek
Keyword(s):  
Pelvic Ring ◽  
Three Dimensional ◽  
Fusion Method ◽  
Two Dimensional ◽  
Posterior Pelvic Ring ◽  
Simple Method ◽  
Sacroiliac Screw ◽  
Screw Insertion ◽  
Multiplanar Reconstructions ◽  
Screw Position

Insertion of sacro-iliac (SI) screws for stabilization of the posterior pelvic ring without intraoperative navigation or three-dimensional imaging can be challenging. The aim of this study was to develop a simple method to visualize the ideal SI screw corridor, on lateral two-dimensional images, corresponding to the lateral fluoroscopic view, used intraoperatively while screw insertion, to prevent neurovascular injury. We used multiplanar reconstructions of pre- and postoperative computed tomography scans (CT) to determine the position of the SI corridor. Then, we processed the dataset into a lateral two-dimensional slice fusion image (SFI) matching head and tip of the screw. Comparison of the preoperative SFI planning and the screw position in the postoperative SFI showed reproducible results. In conclusion, the slice fusion method is a simple technique for translation of three-dimensional planned SI screw positioning into a two-dimensional strict lateral fluoroscopic-like view.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Three-Dimensional Printing of Hydroxyapatite Composites for Biomedical Application

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 353
Author(s):  
Yanting Han ◽  
Qianqian Wei ◽  
Pengbo Chang ◽  
Kehui Hu ◽  
Oseweuba Valentine Okoro ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Biomedical Application ◽  
Three Dimensional ◽  
Antibacterial Properties ◽  
Natural Polymers ◽  
Three Dimensional Printing ◽  
3D Printed ◽  
Dental Applications ◽  
Hard Tissue Engineering

Hydroxyapatite (HA) and HA-based nanocomposites have been recognized as ideal biomaterials in hard tissue engineering because of their compositional similarity to bioapatite. However, the traditional HA-based nanocomposites fabrication techniques still limit the utilization of HA in bone, cartilage, dental, applications, and other fields. In recent years, three-dimensional (3D) printing has been shown to provide a fast, precise, controllable, and scalable fabrication approach for the synthesis of HA-based scaffolds. This review therefore explores available 3D printing technologies for the preparation of porous HA-based nanocomposites. In the present review, different 3D printed HA-based scaffolds composited with natural polymers and/or synthetic polymers are discussed. Furthermore, the desired properties of HA-based composites via 3D printing such as porosity, mechanical properties, biodegradability, and antibacterial properties are extensively explored. Lastly, the applications and the next generation of HA-based nanocomposites for tissue engineering are discussed.

scholarly journals Fish bone-derived interconnected carbon nanofibers for efficient and lightweight microwave absorption

2021 ◽  
Vol 3 (2) ◽  
Author(s):  
Yangyang Gu ◽  
Peng Dai ◽  
Wen Zhang ◽  
Zhanwen Su
Keyword(s):  
Microwave Absorption ◽  
Carbon Nanofibers ◽  
Three Dimensional ◽  
Fish Bone ◽  
Absorption Properties ◽  
Simple Method ◽  
Microwave Absorption Properties ◽  
Absorption Performance ◽  
Microwave Absorption Performance ◽  
Better Than

AbstractIn this work, we demonstrated a simple method for preparing three-dimensional interconnected carbon nanofibers (ICNF) derived from fish bone as an efficient and lightweight microwave absorber. The as-obtained ICNF exhibits excellent microwave absorption performance with a maximum reflection loss of –59.2 dB at the filler content of 15 wt%. In addition, the effective absorption bandwidth can reach 4.96 GHz at the thickness of 2 mm. The outstanding microwave absorption properties can be mainly ascribed to its well-defined interconnected nanofibers architecture and the doping of nitrogen atoms, which are also better than most of the reported carbon-based absorbents. This work paves an attractive way for the design and fabrication of highly efficient and lightweight electromagnetic wave absorbers.

Sign in / Sign up

Export Citation Format

Share Document