Hierarchical flower like double-layer superhydrophobic films fabricated on AZ31 for corrosion protection and self-cleaning

2017 ◽  
Vol 41 (21) ◽  
pp. 12767-12776 ◽  
Author(s):  
Cuiqing Wu ◽  
Qi Liu ◽  
Jingyuan Liu ◽  
Rongrong Chen ◽  
Kazunobu Takahashi ◽  
...  
Keyword(s):  
Contact Angle ◽  
Corrosion Protection ◽  
Double Layer ◽  
Self Assembly ◽  
Self Cleaning

The designed sample is prepared by self-assembly of octadecyltrichlorosilane and deposition of ferric stearate, and the contact angle is 160°.

scholarly journals Self-Cleaning Polyester Fabric Prepared with TiOF2 and Hexadecyltrimethoxysilane

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 387
Author(s):  
Euigyung Jeong ◽  
Heeju Woo ◽  
Yejin Moon ◽  
Dong Yun Lee ◽  
Minjung Jung ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Contact Angle ◽  
Treatment Method ◽  
Polyester Fabric ◽  
Anatase Tio2 ◽  
The Self ◽  
Water Contact ◽  
Direct Fluorination ◽  
Tomato Ketchup ◽  
Self Cleaning

In this study, self-cleaning polyester (PET) fabrics were prepared using TiOF2 and hexadecyltrimethoxysilane(HDS) treatment. TiOF2 was synthesized via direct fluorination of a precursor TiO2 at various reaction temperatures. The prepared PET fabrics had superior photocatalytic self-cleaning properties compared with anatase TiO2/HDS-treated PET fabrics under UV and sunlight with 98% decomposition of methylene blue. TiOF2/HDS-treated PET fabrics also had superior superhydrophobic self-cleaning properties compared with anatase TiO2/HDS-treated PET fabrics with a 161° water contact angle and 6° roll-off angle. After the self-cleaning tests of the non-dyed TiOF2/HDS-treated PET fabrics, we prepared dyed TiOF2/HDS-treated PET fabrics to test practical aspects of the treatment method. These PET fabrics were barely stained by tomato ketchup; even when stained, they could be self-cleaned within 4 h. These results suggest that practical self-cleaning PET fabrics with superhydrophobicity and photocatalytic degradation could be prepared using TiOF2/HDS-treatment.

scholarly journals Fabrication of Superhydrophobic AA5052 Aluminum Alloy Surface with Improved Corrosion Resistance and Self Cleaning Property

Coatings ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 390 ◽  
Author(s):  
Qian Zhao ◽  
Tiantian Tang ◽  
Fang Wang
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Materials Science ◽  
Composite Coatings ◽  
Alloy Surface ◽  
Corrosion Resistant ◽  
Self Cleaning ◽  
Aa5052 Aluminum Alloy ◽  
Aluminum Alloy Surface

The development of a self-cleaning and corrosion resistant superhydrophobic coating for aluminum alloy surfaces that is durable in aggressive conditions has attracted great interest in materials science. In the present study, a superphydrophobic film was fabricated on an AA5052 aluminum alloy surface by the electrodeposition of Ni–Co alloy coating, followed by modification with 6-(N-allyl-1,1,2,2-tetrahydro-perfluorodecyl) amino-1,3,5-triazine-2,4-dithiol monosodium (AF17N). The surface morphology and characteristics of the composite coatings were investigated by means of scanning electron microscopy (SEM), energy dispersive X-ray spectrum (EDS), atomic force microscope (AFM) and contact angle (CA). The corrosion resistance of the coatings was assessed by electrochemical tests. The results showed that the surface exhibited excellent superhydrophobicity and self-cleaning performance with a contact angle maintained at 160° after exposed to the atmosphere for 240 days. Moreover, the superhydrophobic coatings significantly improved the corrosion resistant performance of AA5052 aluminum alloy substrate in 3.5 wt.% NaCl solution.

Preparation of TiO2–SiO2 Hybrid Nanosols Coated Flame-Retardant Polyester Fabric Possessing Dual Contradictory Characteristics of Superhydrophobicity and Self Cleaning Ability

2020 ◽  
Vol 20 (3) ◽  
pp. 1780-1789 ◽  
Author(s):  
Priyanka Katiyar ◽  
Shraddha Mishra ◽  
Anurag Srivastava ◽  
N. Eswara Prasad
Keyword(s):  
Electron Microscopy ◽  
Contact Angle ◽  
Flame Retardant ◽  
Protective Clothing ◽  
Sol Gel ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Vis Spectroscopy ◽  
Self Cleaning

TiO2, SiO2 and their hybrid nanocoatings are prepared on inherent flame retardant textile substrates from titanium(IV)iso-proproxide (TTIP) and tetraethoxysilane (TEOS) precursors using a sol–gel process followed by hydrothermal treatment. The coated samples are further functionalized by hexadecyltrimethoxysilane (HDTMS) to impart superhydrophobicity. Sample characterization of the nanosols, nanoparticles and coated samples are investigated using, X-ray diffractometer, transmission electron microscopy, scanning electron microscopy, UV-Vis spectroscopy, contact angle measurement. Stain degradation test under mild UV irradiation shows almost 54% degradation of coffee stain within 4 hours measured by Spectrophotometer. UV-Vis Absorption Spectroscopy demonstrates complete degradation of methyl orange colorant within 3 hours. Hybrid nanosol coated and HDTMS modified inherent flame retardant polyester surfaces show apparent water contact angle as ~145°, which is much closer to proximity of superhydrophobic surfaces. Thus, the novelty of present work is, by using sol–gel technique, a bi-functional textile surface has been developed which qualifies the very specific requirements of protective clothing like self-cleaning property (imparted by TiO2 nanoparticles) and superhydrophobicity (imparted by SiO2 nanoparticles and further surface modification by HDTMS), which are entirely contradictory in nature, in a single fabric itself. Thus developed textile surfaces also possess the other attributes of protective clothing like flame retardancy and air permeability.

scholarly journals Synthesis, Hydrophilicity and Micellization of Coil–Brush Polystyrene-b-(polyglycidol-g-polyglycidol) Copolymer—Comparison with Linear Polystyrene-b-Polyglycidol

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 253
Author(s):  
Mariusz Gadzinowski ◽  
Maciej Kasprów ◽  
Teresa Basinska ◽  
Stanislaw Slomkowski ◽  
Łukasz Otulakowski ◽  
...  
Keyword(s):  
Contact Angle ◽  
Self Assembly ◽  
Original Method ◽  
Critical Micellization Concentration ◽  
Water Contact ◽  
1H And 13C Nmr ◽  
Similar Composition ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Static Conditions

In this paper, an original method of synthesis of coil–brush amphiphilic polystyrene-b-(polyglycidol-g-polyglycidol) (PS-b-(PGL-g-PGL)) block copolymers was developed. The hypothesis that their hydrophilicity and micellization can be controlled by polyglycidol blocks architecture was verified. The research enabled comparison of behavior in water of PS-b-PGL copolymers and block–brush copolymers PS-b-(PGL-g-PGL) with similar composition. The coil–brush copolymers were composed of PS-b-PGL linear core with average DPn of polystyrene 29 and 13 of polyglycidol blocks. The DPn of polyglycidol side blocks of coil–b–brush copolymers were 2, 7, and 11, respectively. The copolymers were characterized by 1H and 13C NMR, GPC, and FTIR methods. The hydrophilicity of films from the linear and coil–brush copolymers was determined by water contact angle measurements in static conditions. The behavior of coil–brush copolymers in water and their critical micellization concentration (CMC) were determined by UV-VIS using 1,6-diphenylhexa-1,3,5-trien (DPH) as marker and by DLS. The CMC values for brush copolymers were much higher than for linear species with similar PGL content. The results of the copolymer film wettability and the copolymer self-assembly studies were related to fraction of hydrophilic polyglycidol. The CMC for both types of polymers increased exponentially with increasing content of polyglycidol.

scholarly journals Tubular Assembly Formation Induced by Leucine Alignment along the Hydrophobic Helix of Amphiphilic Polypeptides

2021 ◽  
Vol 22 (21) ◽  
pp. 12075
Author(s):  
Mohammed A. Abosheasha ◽  
Toru Itagaki ◽  
Yoshihiro Ito ◽  
Motoki Ueda
Keyword(s):  
Double Layer ◽  
Self Assembly ◽  
Helical Structure ◽  
Tube Formation ◽  
Rolled Sheet ◽  
Α Helix ◽  
Necessary And Sufficient ◽  
Hydrophobic Helix ◽  
Nanotube Dispersion ◽  
Spherical Vesicles

The introduction of α-helical structure with a specific helix–helix interaction into an amphipathic molecule enables the determination of the molecular packing in the assembly and the morphological control of peptide assemblies. We previously reported that the amphiphilic polypeptide SL12 with a polysarcosine (PSar) hydrophilic chain and hydrophobic α-helix (l-Leu-Aib)6 involving the LxxxLxxxL sequence, which induces homo-dimerization due to the concave–convex interaction, formed a nanotube with a uniform 80 nm diameter. In this study, we investigated the importance of the LxxxLxxxL sequence for tube formation by comparing amphiphilic polypeptide SL4A4L4 with hydrophobic α-helix (l-Leu-Aib)2-(l-Ala-Aib)2-(l-Leu-Aib)2 and SL12. SL4A4L4 formed spherical vesicles and micelles. The effect of the LxxxLxxxL sequence elongation on tube formation was demonstrated by studying assemblies of PSar-b-(l-Ala-Aib)-(l-Leu-Aib)6-(l-Ala-Aib) (SA2L12A2) and PSar-b-(l-Leu-Aib)8 (SL16). SA2L12A2 formed nanotubes with a uniform 123 nm diameter, while SL16 assembled into vesicles. These results showed that LxxxLxxxL is a necessary and sufficient sequence for the self-assembly of nanotubes. Furthermore, we fabricated a double-layer nanotube by combining two kinds of nanotubes with 80 and 120 nm diameters—SL12 and SA2L12A2. When SA2L12A2 self-assembled in SL12 nanotube dispersion, SA2L12A2 initially formed a rolled sheet, the sheet then wrapped the SL12 nanotube, and a double-layer nanotube was obtained.

scholarly journals Hydrophobic and Anti-Fouling Performance of Surface on Parabolic Morphology

2020 ◽  
Vol 17 (2) ◽  
pp. 644
Author(s):  
Yu Li ◽  
Shengke Yang ◽  
Yangyang Chen ◽  
Dan Zhang
Keyword(s):  
Contact Angle ◽  
Chemical Oxidation ◽  
The Self ◽  
Separation Performance ◽  
Copper Sheet ◽  
Water Separation ◽  
Cleaning Performance ◽  
Oil Water Separation ◽  
Oil Water ◽  
Self Cleaning

The hydrophobicity and anti-fouling properties of materials have important application value in industrial and agricultural production and people’s daily life. To study the relationship between the unit width L0 of the parabolic hydrophobic material and the hydrophobicity and anti-fouling properties, the rough surface structure of the parabolic with different widths was prepared by grinding with different SiC sandpapers, and further, to obtain hydrophobic materials through chemical oxidation and chemical etching, and modification with stearic acid (SA). The morphology, surface wetting and anti-fouling properties of the modified materials were characterized by SEM and contact angle measurement. The oil–water separation performance and self-cleaning performance of the materials were explored. The surface of the modified copper sheet forms a rough structure similar to a paraboloid. When ground with 1500 grit SiC sandpaper, it is more conducive to increase the hydrophobicity of the copper sheet surface and increase the contact angle of water droplets on the copper surface. Additionally, the self-cleaning and anti-fouling experiments showed that as L0 decreases, copper sheets were less able to stick to foreign things such as soil, and the better the self-cleaning and anti-fouling performance was. Based on the oil–water separation experiment of copper mesh, the lower L0 has a higher oil–water separation efficiency. The results showed that material with parabolic morphology has great self-cleaning, anti-fouling, and oil–water separation performance. The smaller the L0 was, the larger the contact angle and the better hydrophobic performance and self-cleaning performance were.

scholarly journals Bio-Inspired Fluorine-Free Self-Cleaning Polymer Coatings

Coatings ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 436 ◽  
Author(s):  
Lionel Wasser ◽  
Sara Dalle Vacche ◽  
Feyza Karasu ◽  
Luca Müller ◽  
Micaela Castellino ◽  
...  
Keyword(s):  
Self Assembly ◽  
Polymer Coatings ◽  
Sliding Angle ◽  
Water Contact ◽  
Uv Curable ◽  
Molecular Weights ◽  
Air Interface ◽  
Creep Time ◽  
Self Cleaning ◽  
Printing Processes

Bio-inspired fluorine-free and self-cleaning polymer coatings were developed using a combination of self-assembly and UV-printing processes. Nasturtium and lotus leaves were selected as natural template surfaces. A UV-curable acrylate oligomer and three acrylated siloxane comonomers with different molecular weights were used. The spontaneous migration of the comonomers towards the polymer–air interface was found to be faster for comonomers with higher molecular weight, and enabled to create hydrophobic surfaces with a water contact angle (WCA) of 105°. The replication fidelity was limited for the nasturtium surface, due to a lack of replication of the sub-micron features. It was accurate for the lotus leaf surface whose hierarchical texture, comprising micropapillae and sub-micron crystalloids, was well reproduced in the acrylate/comonomer material. The WCA of synthetic replica of lotus increased from 144° to 152° with increasing creep time under pressure to 5 min prior to polymerization. In spite of a water sliding angle above 10°, the synthetic lotus surface was self-cleaning with water droplets when contaminated with hydrophobic pepper particles, provided that the droplets had some kinetic energy.

Self-assembly of SiO2 films on aluminum flakes for corrosion protection

2020 ◽  
pp. 1-10
Author(s):  
Qixing Zhang ◽  
Weiming Zhou ◽  
Ibrahim Lawan ◽  
Samuel Etuk ◽  
Mingxin Zhang ◽  
...  
Keyword(s):  
Corrosion Protection ◽  
Self Assembly ◽  
Sio2 Films
Sign in / Sign up

Export Citation Format

Share Document