Largely enhanced dielectric constant of PVDF nanocomposites through a core–shell strategy

2018 ◽  
Vol 20 (4) ◽  
pp. 2777-2786 ◽  
Author(s):  
Minhao Yang ◽  
Hang Zhao ◽  
Chaohe Hu ◽  
Paul Haghi-Ashtiani ◽  
Delong He ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Core Shell

Core–shell structured TiO2@C nanowires were synthesized and the dielectric properties of the nanocomposites could be largely enhanced after incorporating these core–shell structured nanowires.

Enhanced dielectric properties of conductive-dielectric composites by reducing particle size and core@shell method

2018 ◽  
Vol 11 (01) ◽  
pp. 1850010 ◽  
Author(s):  
Yuqiang Guo ◽  
Yifei Wang ◽  
Yaxuan Ren ◽  
Mingzhu Fu ◽  
Hongmei Ma ◽  
...  
Keyword(s):  
Particle Size ◽  
Dielectric Constant ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Mass Fraction ◽  
Core Shell ◽  
Particle Sizes ◽  
Conductive Particle ◽  
Threshold Theory ◽  
Conductive Polyaniline

Based on the percolation threshold theory of conductive-dielectric composites, the dielectric constant can be improved more by adding a certain mass fraction of conductive particle into polymer matrix. However, the dielectric loss increases with the increasing mass fraction of conductive particle. In this paper, conductive Polyaniline (PANI) with different particle sizes is utilized to illustrate that reducing particle size can improve the dielectric properties. The dielectric constant is increased from 319 to 540, and dielectric loss is decreased from 2.34 to 0.85 when PANI with smaller particle size is used. Moreover, PANI coated with an insulating surfactant layer can further improve the dielectric properties, the experimental results show that the dielectric constant of the composite could be more than 1000, while the dielectric loss is 0.35 at 1[Formula: see text]KHz.

scholarly journals Core–shell structured Ag@C nanocables for flexible ferroelectric polymer nanodielectric materials with low percolation threshold and excellent dielectric properties

RSC Advances ◽  
2018 ◽  
Vol 8 (1) ◽  
pp. 1-9 ◽  
Author(s):  
Zhihui Chen ◽  
Hengfeng Li ◽  
Guangyou Xie ◽  
Ke Yang
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Percolation Threshold ◽  
Nanocomposite Materials ◽  
Core Shell ◽  
Ferroelectric Polymer

Flexible Ag@C-NC/PVDF nanocomposite materials with low percolation threshold and dielectric constant of 295 at 1 kHz.

The effects of TiC@AlOOH core–shell nanoparticles on the dielectric properties of PVDF based nanocomposites

RSC Advances ◽  
2016 ◽  
Vol 6 (30) ◽  
pp. 25015-25022 ◽  
Author(s):  
Weng Ling ◽  
Li Hongxia ◽  
Ju Peihai ◽  
Wang Ting ◽  
Liu Lizhu
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Nanocomposite Films ◽  
Core Shell ◽  
Shell Nanoparticles ◽  
Core Shell Nanoparticles

The dielectric constant of PVDF/TiC@AlOOH nanocomposite films is as high as 1.8 × 107 at 100 Hz.

Dielectric Properties and Microstructure of BaTiO3 Ceramics

2002 ◽  
Vol 718 ◽  
Author(s):  
Dae-Chul Park ◽  
Jun-ichi Itoh ◽  
Isao Sakaguchi ◽  
Naoki Ohashi ◽  
Toyohiko Yano ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Curie Temperature ◽  
Secondary Phase ◽  
Dielectric Constants ◽  
Core Shell ◽  
Temperature Range ◽  
The Core ◽  
La Doped ◽  
Mg Doped

AbstractDielectric properties and microstructure were investigated in BaTiO3 ceramics with various additives, Ho2O3, MgO, Ho2O3/MgO, and La2O3. The dielectric constants were increased up to ∼4000 and ∼3000 at 25°C in the 1 mol% Ho-doped and 0.5 mol% Mg-doped BaTiO3 materials, respectively. The BaTiO3 material codoped with 3 mol% Ho + 1.5 mol% Mg led to increase dielectric constant up to ∼6000 at 25°C and the dielectric constant peak around Curie temperature was suppressed at temperature range of from 25°C to 125°C. The size of BaTiO3 grains depended on the content and kind of an additive. Core-shell grains and secondary phase were also dependent on an additive. Core-shell grains were formed completely in Ho-doped BaTiO3 except for 0.5 mol%, but the structure was little observed in Mg- and La-doped BaTiO3 material. Codoped BaTiO3 also formed the core-shell grains.

Tuning the mechanical and dielectric properties of zinc incorporated hydroxyapatite

2020 ◽  
Vol 16 ◽  
Author(s):  
Alliya Qamar ◽  
Rehana Zia ◽  
Madeeha Riaz
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Bone Growth ◽  
Healing Process ◽  
Secondary Phase ◽  
Chemical Precipitation ◽  
Hexagonal Structure ◽  
Precipitation Method ◽  
Low Frequencies ◽  
A Minor

Background: Hydroxyapatite is similar to bone mineral in chemical composition, has good biocompatibility with host tissue and bone. Objective: This work aims to tailor the mechanical and dielectric properties of hydroxyapatite with zinc sudstitution, to improve wearability of implant and accelerate the healing process. Method: Pure and zinc incorporated hydroxyapatite Ca10(PO4)6(OH)2 samples have been successfully prepared by means of the chemical precipitation method. Results: The results showed that hydroxyapatite(Hap) having hexagonal structure was the major phase identified in all the samples. It was found that secondary phase of β-tricalcium phosphate (β-TCP) formed due to addition of Zinc resulting in biphasic structure BCP (Hap + β-TCP). A minor phase of ZnO also formed for higher concentration of Zn (Zn ≥ 2mol%) doping. It was found that the Zn incorporation to Hap enhanced both mechanical and dielectric properties without altering the bioactive properties. The microhardness increased upto 0.87 GPa for Zn concentration equal to 1.5mol%, which is comparable to the human bone ~0.3 - 0.9 GPa. The dielectric properties evaluated in the study showed that 1.5 mol% Zn doped hydroxyapatite had highest dielectric constant. Higher values of dielectric constant at low frequencies signifies its importance in healing processes and bone growth due to polarization of the material under the influence of electric field. Conclusion: Sample Z1.5 having 1.5 mol% Zn doping showed the most optimized properties suitable for bone regeneration applications.

scholarly journals Effect of Terminal Groups on Thermomechanical and Dielectric Properties of Silica–Epoxy Composite Modified by Hyperbranched Polyester

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2451
Author(s):  
Jianwen Zhang ◽  
Dongwei Wang ◽  
Lujia Wang ◽  
Wanwan Zuo ◽  
Lijun Zhou ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Binding Energy ◽  
Epoxy Resin ◽  
Volume Fraction ◽  
Epoxy Composite ◽  
Mean Square Displacement ◽  
Mean Square ◽  
Hyperbranched Polyester ◽  
Free Volume Fraction

To study the effect of hyperbranched polyester with different kinds of terminal groups on the thermomechanical and dielectric properties of silica–epoxy resin composite, a molecular dynamics simulation method was utilized. Pure epoxy resin and four groups of silica–epoxy resin composites were established, where the silica surface was hydrogenated, grafted with silane coupling agents, and grafted with hyperbranched polyester with terminal carboxyl and terminal hydroxyl, respectively. Then the thermal conductivity, glass transition temperature, elastic modulus, dielectric constant, free volume fraction, mean square displacement, hydrogen bonds, and binding energy of the five models were calculated. The results showed that the hyperbranched polyester significantly improved the thermomechanical and dielectric properties of the silica–epoxy composites compared with other surface treatments, and the terminal groups had an obvious effect on the enhancement effect. Among them, epoxy composite modified by the hyperbranched polyester with terminal carboxy exhibited the best thermomechanical properties and lowest dielectric constant. Our analysis of the microstructure found that the two systems grafted with hyperbranched polyester had a smaller free volume fraction (FFV) and mean square displacement (MSD), and the larger number of hydrogen bonds and greater binding energy, indicating that weaker strength of molecular segments motion and stronger interfacial bonding between silica and epoxy resin matrix were the reasons for the enhancement of the thermomechanical and dielectric properties.

Influence of Ca-Doping on Structural, Magnetic and Dielectric Properties of Ba3Co2-xCaxFe24O41 Hexaferrite Powders

2015 ◽  
Vol 241 ◽  
pp. 226-236 ◽  
Author(s):  
Neha Solanki ◽  
Rajshree B. Jotania
Keyword(s):  
Dielectric Constant ◽  
Dielectric Properties ◽  
Sol Gel ◽  
Calcium Content ◽  
Combustion Method ◽  
Dielectric Behavior ◽  
Dielectric Parameters ◽  
Ca Doping ◽  
Auto Combustion ◽  
Magnetic And Dielectric Properties

Influence of Ca substitution on structural, magnetic and dielectric properties of Ba3Co2-xCaxFe24O41(where x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0), prepared by Sol-Gel auto-combustion method, has been investigated in present studies. The obtained powder was sintered at 950 oC for 4 hrs. in the static air atmosphere. Structural analysis of Ca-doped Ba3Co2-xCaxFe24O41powders revealed pure Z-type hexaferrite phase at low temperature. The frequency dependent dielectric constant (Єʹ) and magnetic properties such as remanent magnetization (Mr), saturation magnetization (Ms) and coercivity (Hc) were studied. It is observed that coercivity increased gradually with increase in calcium content. The real dielectric constant (Єʹ) and dielectric loss tangent (tan δ) were studied in the frequency range of 20Hz to 2MHz. The dielectric parameters for all samples show normal dielectric behavior as observed in hexaferrites. Contents of Paper

Enhanced dielectric properties and thermostability in polyimide composites with core-shell structured polyimide@BaTiO3 nanoparticles

2021 ◽  
pp. 095400832199352
Author(s):  
Wei Deng ◽  
Guanguan Ren ◽  
Wenqi Wang ◽  
Weiwei Cui ◽  
Wenjun Luo
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
Energy Density ◽  
Breakdown Strength ◽  
In Situ Polymerization ◽  
Dielectric Materials ◽  
High Energy ◽  
Amic Acid ◽  
High Energy Density ◽  
Core Shell

Polymer composites with high dielectric constant and thermal stability have shown great potential applications in the fields relating to the energy storage. Herein, core-shell structured polyimide@BaTiO3 (PI@BT) nanoparticles were fabricated via in-situ polymerization of poly(amic acid) (PAA) and the following thermal imidization, then utilized as fillers to prepare PI composites. Increased dielectric constant with suppressed dielectric loss, and enhanced energy density as well as heat resistance were simultaneously realized due to the presence of PI shell between BT nanoparticles and PI matrix. The dielectric constant of PI@BT/PI composites with 55 wt% fillers increased to 15.0 at 100 Hz, while the dielectric loss kept at low value of 0.0034, companied by a high energy density of 1.32 J·cm−3, which was 2.09 times higher than the pristine PI. Moreover, the temperature at 10 wt% weight loss reached 619°C, demonstrating the excellent thermostability of PI@BT/PI composites. In addition, PI@BT/PI composites exhibited improved breakdown strength and toughness as compared with the BT/PI composites due to the well dispersion of PI@BT nanofillers and the improved interfacial interactions between nanofillers and polymer matrix. These results provide useful information for the structural design of high-temperature dielectric materials.

Plasticizer effect on dielectric properties of poly(methyl methacrylate)/titanium dioxide composites

2021 ◽  
pp. 096739112110147
Author(s):  
Ufuk Abaci ◽  
H Yuksel Guney ◽  
Mesut Yilmazoglu
Keyword(s):  
Dielectric Constant ◽  
Titanium Dioxide ◽  
Dielectric Properties ◽  
Methyl Methacrylate ◽  
Pure Pmma ◽  
Segmental Mobility ◽  
Scanning Calorimetry ◽  
Poly Methyl Methacrylate ◽  
Casting Technique ◽  
Lcr Meter

The effect of plasticizer on dielectric properties of poly(methyl methacrylate) (PMMA)/titanium dioxide (TiO2) composites was investigated. Propylene carbonate (PC) was used as plasticizer in the samples which were prepared with the conventional solvent casting technique. Scanning Electron Microscopy with Energy Dispersive X-Ray Analysis (SEM-EDX) and Differential scanning calorimetry (DSC) analyses and LCR Meter measurements (performed between 300 K and 400 K), were conducted to examine the properties of the composites. With the addition of plasticizer, the thermal properties have changed and the dielectric constant of the composite has increased significantly. The glass transition temperature of pure PMMA measured 121.7°C and this value did not change significantly with the addition of TiO2, however, 112°C was measured in the sample with the addition 4 ml of PC. While the dielectric constant of pure PMMA was 3.64, the ε′ value increased to 5.66 with the addition of TiO2 and reached 12.6 with the addition of 4 ml PC. These changes have been attributed to increase in amorphous ratio that facilitates polymer dipolar and segmental mobility.

Sign in / Sign up

Export Citation Format

Share Document