Conductive single nanowires formed and analysed on microfluidic devices

2016 ◽  
Vol 4 (39) ◽  
pp. 9235-9244 ◽  
Author(s):  
Yanlong Xing ◽  
Norbert Esser ◽  
Petra S. Dittrich
Keyword(s):  
Optical Properties ◽  
Microfluidic Device ◽  
Microfluidic Devices ◽  
Metal Salts ◽  
Reaction Flask ◽  
Electrical Conductivities ◽  
Single Nanowires ◽  
Derivatives Of

In this work, we studied the formation of fibres and particles made of metal salts and derivatives of tetrathiafulvalene (TTF) on a microfluidic device and in a conventional reaction flask, and characterized their morphologies, optical properties and electrical conductivities.

scholarly journals Synthesis of New Derivatives of BEDT-TTF: Installation of Alkyl, Ethynyl, and Metal-Binding Side Chains and Formation of Tris(BEDT-TTF) Systems

2021 ◽  
Vol 7 (8) ◽  
pp. 110
Author(s):  
Songjie Yang ◽  
Matteo Zecchini ◽  
Andrew Brooks ◽  
Sara Krivickas ◽  
Desiree Dalligos ◽  
...  
Keyword(s):  
Metal Binding ◽  
Tricarboxylic Acid ◽  
Metal Salts ◽  
Side Chain ◽  
Side Chains ◽  
Ethynyl Group ◽  
X Ray ◽  
Transition Metal Salts ◽  
Alkyl Side Chains ◽  
Derivatives Of

The syntheses of new BEDT-TTF derivatives are described. These comprise BEDT-TTF with one ethynyl group (HC≡C-), with two (n-heptyl) or four (n-butyl) alkyl side chains, with two trans acetal (-CH(OMe)2) groups, with two trans aminomethyl (-CH2NH2) groups, and with an iminodiacetate (-CH2N(CH2CO2−)2 side chain. Three transition metal salts have been prepared from the latter donor, and their magnetic properties are reported. Three tris-donor systems are reported bearing three BEDT-TTF derivatives with ester links to a core derived from benzene-1,3,5-tricarboxylic acid. The stereochemistry and molecular structure of the donors are discussed. X-ray crystal structures of two BEDT-TTF donors are reported: one with two CH(OMe)2 groups and with one a -CH2N(CH2CO2Me)2 side chain.

scholarly journals Micropipette-Based Microfluidic Device for Monodisperse Microbubbles Generation

Micromachines ◽  
2018 ◽  
Vol 9 (8) ◽  
pp. 387
Author(s):  
Carlos Toshiyuki Matsumi ◽  
Wilson José da Silva ◽  
Fábio Kurt Schneider ◽  
Joaquim Miguel Maia ◽  
Rigoberto E. M. Morales ◽  
...  
Keyword(s):  
Electric Fields ◽  
Microfluidic Device ◽  
Soft Lithography ◽  
Low Cost ◽  
Characteristic Curve ◽  
Microfluidic Devices ◽  
Average Diameter ◽  
Internal Diameter ◽  
Medical Diagnostic ◽  
Average Size

Microbubbles have various applications including their use as carrier agents for localized delivery of genes and drugs and in medical diagnostic imagery. Various techniques are used for the production of monodisperse microbubbles including the Gyratory, the coaxial electro-hydrodynamic atomization (CEHDA), the sonication methods, and the use of microfluidic devices. Some of these techniques require safety procedures during the application of intense electric fields (e.g., CEHDA) or soft lithography equipment for the production of microfluidic devices. This study presents a hybrid manufacturing process using micropipettes and 3D printing for the construction of a T-Junction microfluidic device resulting in simple and low cost generation of monodisperse microbubbles. In this work, microbubbles with an average size of 16.6 to 57.7 μm and a polydispersity index (PDI) between 0.47% and 1.06% were generated. When the device is used at higher bubble production rate, the average diameter was 42.8 μm with increased PDI of 3.13%. In addition, a second-order polynomial characteristic curve useful to estimate micropipette internal diameter necessary to generate a desired microbubble size is presented and a linear relationship between the ratio of gaseous and liquid phases flows and the ratio of microbubble and micropipette diameters (i.e., Qg/Ql and Db/Dp) was found.

scholarly journals Manufacturing of Microfluidic Devices with Interchangeable Commercial Fiber Optic Sensors

Sensors ◽  
2021 ◽  
Vol 21 (22) ◽  
pp. 7493
Author(s):  
Krystian L. Wlodarczyk ◽  
William N. MacPherson ◽  
Duncan P. Hand ◽  
M. Mercedes Maroto-Valer
Keyword(s):  
Porous Structure ◽  
Steady Flow ◽  
Microfluidic Device ◽  
Fiber Optic ◽  
Dynamic Pressure ◽  
Pressure Sensors ◽  
Microfluidic Devices ◽  
Fiber Optic Sensors ◽  
Valuable Insight ◽  
Local Pressure

In situ measurements are highly desirable in many microfluidic applications because they enable real-time, local monitoring of physical and chemical parameters, providing valuable insight into microscopic events and processes that occur in microfluidic devices. Unfortunately, the manufacturing of microfluidic devices with integrated sensors can be time-consuming, expensive, and “know-how” demanding. In this article, we describe an easy-to-implement method developed to integrate various “off-the-shelf” fiber optic sensors within microfluidic devices. To demonstrate this, we used commercial pH and pressure sensors (“pH SensorPlugs” and “FOP-MIV”, respectively), which were “reversibly” attached to a glass microfluidic device using custom 3D-printed connectors. The microfluidic device, which serves here as a demonstrator, incorporates a uniform porous structure and was manufactured using a picosecond pulsed laser. The sensors were attached to the inlet and outlet channels of the microfluidic pattern to perform simple experiments, the aim of which was to evaluate the performance of both the connectors and the sensors in a practical microfluidic environment. The bespoke connectors ensured robust and watertight connection, allowing the sensors to be safely disconnected if necessary, without damaging the microfluidic device. The pH SensorPlugs were tested with a pH 7.01 buffer solution. They measured the correct pH values with an accuracy of ±0.05 pH once sufficient contact between the injected fluid and the measuring element (optode) was established. In turn, the FOP-MIV sensors were used to measure local pressure in the inlet and outlet channels during injection and the steady flow of deionized water at different rates. These sensors were calibrated up to 140 mbar and provided pressure measurements with an uncertainty that was less than ±1.5 mbar. Readouts at a rate of 4 Hz allowed us to observe dynamic pressure changes in the device during the displacement of air by water. In the case of steady flow of water, the pressure difference between the two measuring points increased linearly with increasing flow rate, complying with Darcy’s law for incompressible fluids. These data can be used to determine the permeability of the porous structure within the device.

A Multifunctional Microfluidic Device Based on Bifurcation Geometry

2010 ◽  
Author(s):  
Ahmed Fadl ◽  
Stefanie Demming ◽  
Zongqin Zhang ◽  
Bjo¨rn Hoxhold ◽  
Stephanus Bu¨ttgenbach ◽  
...  
Keyword(s):  
Microfluidic Device ◽  
Microfluidic Devices ◽  
Optical Lithography ◽  
Working Fluid ◽  
The Novel ◽  
Flow Rates ◽  
Single Function ◽  
Fluidic Device ◽  
Bifurcation Structures ◽  
Novel Design

Developing multifunctional devices are essential to realize more efficient Microsystems. With miniaturization processes taking place in many different applications, the rooms for single function microfluidic devices are limited. In this study, we introduce a multifunctional micro fluidic device based on bifurcation geometry which is capable of performing pumping and mixing at the same time. Optical lithography is used to fabricate the designed microfluidic device. The microfluidic device is tested at low actuator frequencies, and ethanol is employed as a working fluid. The operational principles are based on rectifying the oscillatory flows by using bifurcation structures for flow rectification. The results prove the feasibility of the novel design, and results are presented in terms of flow rates and maximum back pressures.

scholarly journals A diffusion-based microfluidic device for single-cell RNA-seq

Lab on a Chip ◽  
2019 ◽  
Vol 19 (7) ◽  
pp. 1247-1256 ◽  
Author(s):  
Mimosa Sarma ◽  
Jiyoung Lee ◽  
Sai Ma ◽  
Song Li ◽  
Chang Lu
Keyword(s):  
Single Cell ◽  
Microfluidic Device ◽  
Microfluidic Devices ◽  
Rna Seq ◽  
Transcriptomic Studies

Scalable microfluidic devices containing reaction and loading chambers were developed to conduct single-cell transcriptomic studies.

scholarly journals Low Cost Micro Milling Machine for Prototyping Plastic Microfluidic Devices

Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 707 ◽  
Author(s):  
Md Mubarak Hossain ◽  
Tanzilur Rahman
Keyword(s):  
Developing Countries ◽  
Microfluidic Device ◽  
Low Cost ◽  
Microfluidic Devices ◽  
Micro Milling ◽  
Biological Research ◽  
Milling Machine ◽  
Plastic Materials ◽  
Milling Machines

Micro-milling is one of the commonly used methods of fabrication of microfluidic devices necessary for cell biological research and application. Commercial micro-milling machines are expensive, and researchers in developing countries can’t afford them. Here, we report the design and the development of a low-cost (<130 USD) micro milling machine and asses the prototyping capabilities of microfeatures in plastic materials. We demonstrate that the developed machine can be used in fabricating the plastic based microfluidic device.

Synthesis and Optical Properties of Cinnamylidene Derivatives of Malononitrile Trimer

2019 ◽  
Vol 55 (11) ◽  
pp. 1731-1734 ◽  
Author(s):  
I. N. Bardasov ◽  
A. U. Alekseeva ◽  
N. P. Dianov ◽  
A. A. Mikhailov ◽  
O. V. Ershov
Keyword(s):  
Optical Properties ◽  
Derivatives Of
Sign in / Sign up

Export Citation Format

Share Document