The effect of 2-mercaptobenzothiazole on laser-assisted electroless copper plating

RSC Advances ◽  
2016 ◽  
Vol 6 (45) ◽  
pp. 38647-38652
Author(s):  
Sisi Xiang ◽  
Weiping Li ◽  
Zhiyuan Qian ◽  
Liqun Zhu ◽  
Huicong Liu
Keyword(s):  
Electroless Plating ◽  
Copper Plating ◽  
Electroless Copper Plating ◽  
Plating Bath ◽  
Copper Coatings ◽  
Electroless Copper

Copper coatings on PET substrates (conductive treatment through laser direct structuring) were prepared from an electroless plating bath. The coatings' morphology and the plating rate were shown in the figure at various concentrations of 2-MBT.

POLYMER BRUSH-INDUCED ELECTROLESS COPPER PLATING TO FABRICATE Cu/CaCO3 COMPOSITE POWDER

2020 ◽  
pp. 2050053
Author(s):  
QIHONG LI ◽  
GUANGCHAO QIN ◽  
JUNJUN HUANG ◽  
CHENGMEI GUI ◽  
JINGUO BEI ◽  
...  
Keyword(s):  
Noble Metal ◽  
Electroless Plating ◽  
Composite Powder ◽  
Low Cost ◽  
Polymer Brush ◽  
Catalytic Site ◽  
Metal Catalyst ◽  
Copper Plating ◽  
Electroless Copper Plating ◽  
Electroless Copper

Electroless plating can be used to prepare metal particle/CaCO3 composite powder, but the use of noble metal as catalytic site would increase the cost. In this work, we adopt the combined 3-amino-propyltriethoxysilane (KH550) modification and NiCl2 activation to coat CaCO3 powder by a uniform layer of Ni particles/polymer brush which acts as non-noble metal catalyst, then, a low-cost electroless plating to prepare Cu particle/CaCO3 composite powder was developed. Results showed hydrolyzed KH550 coated on the CaCO3 surface in the form of polymer brush. The active group on the polymer brush surface could chemisorb Ni[Formula: see text] and then Ni particles/polymer brush was attached on its surface. The Ni particle/polymer brush structure acted as catalytic site and could catalyze electroless copper plating on its surface. The [Formula: see text] is 1%, its average diameter is about 100[Formula: see text]nm. This means that the dependable technology has great potential application in preparing metal inorganic powder at a low cost.

scholarly journals Indirect determination of pH in electroless copper plating bath by spectrophotometry.

1985 ◽  
Vol 36 (7) ◽  
pp. 289-290
Author(s):  
Shozo MIZUMOTO ◽  
Hidemi NAWAFUNE ◽  
Motoo KAWASAKI ◽  
Akemi KINOSHITA ◽  
Ken ARAKI
Keyword(s):  
Copper Plating ◽  
Electroless Copper Plating ◽  
Plating Bath ◽  
Indirect Determination ◽  
Electroless Copper

Direct Electroless Copper Plating on Polyimide for FPCB Applications

2007 ◽  
Vol 544-545 ◽  
pp. 709-712 ◽  
Author(s):  
Jae Ho Lee
Keyword(s):  
Electroless Plating ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Copper Plating ◽  
Optimum Conditions ◽  
Electroless Copper Plating ◽  
Additive Process ◽  
Copper Line ◽  
Electroless Copper ◽  
Copper Seed Layer

As electronic devices are getting smaller and lighter, the density of copper lines on flexible printed circuit board (FPCB) is getting higher. Conventionally, subtractive method was used for copper line on a flexible films, however, as the line pitch is getting smaller, the lateral etching of copper cause serious problem. To replace the subtractive method, semi-additive method was used for fine pitch copper line fabrication. In semi additive process, sputtered layer for the electroplating copper was required. The feasibility of electroless plating to replace high cost sputtered copper seed layer was investigated. Electroless depositions of copper were conducted on different substrate to find optimum conditions of electroless copper plating. To find optimum conditions, the effects and selectivity of activation method on several substrates were also investigated. The adhesion strength between polyimide and copper was improved by treating the polyimide surface with butylamines. Pretreatment prior to electroless plating is very sensitive and surface dependent. Surface morphologies were investigated with FESEM.

Selective metallization of alumina ceramics by inkjet printing combined with electroless copper plating

2016 ◽  
Vol 4 (43) ◽  
pp. 10240-10245 ◽  
Author(s):  
Jin-ju Chen ◽  
Yan-long Guo ◽  
Yan Wang ◽  
Jing Zhang ◽  
Huo-jun Li ◽  
...  
Keyword(s):  
Electroless Plating ◽  
Inkjet Printing ◽  
Copper Plating ◽  
Alumina Ceramics ◽  
Electroless Copper Plating ◽  
Efficient Approach ◽  
Electroless Copper

A convenient and efficient approach for selective metallization of alumina ceramics via inkjet printing followed by electroless plating was developed.

Sign in / Sign up

Export Citation Format

Share Document