scholarly journals Fully spray-coated organic solar cells on woven polyester cotton fabrics for wearable energy harvesting applications

2016 ◽  
Vol 4 (15) ◽  
pp. 5561-5568 ◽  
Author(s):  
S. Arumugam ◽  
Y. Li ◽  
S. Senthilarasu ◽  
R. Torah ◽  
A. L. Kanibolotsky ◽  
...  
Keyword(s):  
Solar Cells ◽  
Energy Harvesting ◽  
Organic Solar Cells ◽  
Spray Coating ◽  
Cotton Fabrics ◽  
Coating Technique

A novel use of spray-coating technique to fabricate organic solar cells on textiles for wearable energy harvesting applications.

Performance evaluation of PTB7 : PC71BM based organic solar cells fabricated by spray coating method using chlorine free solvent

RSC Advances ◽  
2015 ◽  
Vol 5 (69) ◽  
pp. 56262-56269 ◽  
Author(s):  
Murugesan Vijay Srinivasan ◽  
Norio Tsuda ◽  
Paik-Kyun Shin ◽  
Shizuyasu Ochiai
Keyword(s):  
Performance Evaluation ◽  
Solar Cells ◽  
Organic Solar Cells ◽  
Spray Coating ◽  
Environmental Issues ◽  
Coating Technique ◽  
Coating Method

The PTB7 : PC71BM polymer based solar cells have been successfully fabricated by spin and spray coating technique using chlorine-free solvent (xylene), which are desirable to reduce environmental issues.

Stretchable ITO‐Free Organic Solar Cells with Intrinsic Anti‐Reflection Substrate for High‐Efficiency Outdoor and Indoor Energy Harvesting

2021 ◽  
Vol 31 (16) ◽  
pp. 2010172
Author(s):  
Jiaming Huang ◽  
Zhiwei Ren ◽  
Yaokang Zhang ◽  
Kuan Liu ◽  
Hengkai Zhang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Energy Harvesting ◽  
Organic Solar Cells ◽  
High Efficiency

Spray coating fabrication of organic solar cells bypassing the limit of orthogonal solvents

2013 ◽  
Vol 102 (20) ◽  
pp. 203307 ◽  
Author(s):  
Silvia Colella ◽  
Marco Mazzeo ◽  
Giovanna Melcarne ◽  
Sonia Carallo ◽  
Giuseppe Ciccarella ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Spray Coating

Roll-to-Roll Fabrication of Bulk Heterojunction Plastic Solar Cells using the Reverse Gravure Coating Technique

2008 ◽  
Vol 1091 ◽  
Author(s):  
Daniel Tobjork ◽  
Harri Aarnio ◽  
Tapio Mäkelä ◽  
Ronald Österbacka
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Bulk Heterojunction ◽  
Acid Methyl Ester ◽  
Ambient Air ◽  
Plastic Substrate ◽  
Heterojunction Solar Cells ◽  
Coating Technique ◽  
Roll To Roll ◽  
Poly Styrene Sulfonate

AbstractThe roll-to-roll reverse gravure (RG) coating technique was used to produce thin homogeneous films (∼100 nm) for organic bulk heterojunction solar cells. The conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and the active layer regioregular poly(3-hexylthiophene-2,5-diyl):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM) were successfully subsequently RG coated on an ITO covered plastic substrate in ambient air. Working solar cells were achieved after annealing and thermal evaporation of the top contact. The AM1.5 power conversion efficiency (PCE) of the RG coated organic solar cells was determined to 0.74% (at 100 mW/cm2). This was very similar to the results of a reference device that was spin coated on a glass substrate in a nitrogen glove box.

Construction and Evaluation of Organic Solar Cells Using a Spray-Coating Method

2010 ◽  
Author(s):  
Y. Murakami ◽  
H. Ishihara ◽  
T. Mizutani ◽  
K. Kojima ◽  
S. Ochiai
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Spray Coating ◽  
Coating Method

scholarly journals Effect of Spraying Parameters on the Morphology of Spray-Coated Active Layers for Organic Solar Cells

2018 ◽  
Vol 7 (3.18) ◽  
pp. 75
Author(s):  
Nur Tahirah Razali ◽  
Khairunisa Kamarudin ◽  
Shusei Inaba ◽  
Mahshuri Yusof ◽  
Yeng Weng Leong ◽  
...  
Keyword(s):  
Solar Cells ◽  
Film Thickness ◽  
Organic Solar Cells ◽  
Spin Coating ◽  
Mass Production ◽  
Low Cost ◽  
Applied Pressure ◽  
Spray Coating ◽  
Processing Parameters ◽  
Line Production

Over the past decade, organic solar cells (OSCs) have demonstrated their great potential for the low-cost mass production of renewable energy.  However, the conventional active layer deposition technique (spin-coating) is not suitable for mass production due to its incompatibility with the roll-to-roll process. Spray-coating is a promising candidate for in-line production of OSCs but parameters such as distance between the spray nozzle and substrate, applied pressure and number of sprays should be optimized to produce adequate film thickness and morphology. Here, we verified how these processing parameters influence the thin film properties and observed that film thickness increases with decreasing nozzle-substrate distance, increasing number of sprays or applied pressure. The processing parameters were adjusted to produce spray-coated films with similar properties to the spin-coated ones thus confirming that spray-coating could replace spin-coating for mass production of OSC devices.  

Sign in / Sign up

Export Citation Format

Share Document