Cyclic behaviors of amorphous shape memory polymers

Soft Matter ◽  
2016 ◽  
Vol 12 (13) ◽  
pp. 3234-3245 ◽  
Author(s):  
Kai Yu ◽  
Hao Li ◽  
Amber J. W. McClung ◽  
Gyaneshwar P. Tandon ◽  
Jeffery W. Baur ◽  
...  
Keyword(s):  
Cyclic Loading ◽  
Service Life ◽  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Deformation Resistance ◽  
Recovery Ratio ◽  
Loading Conditions

Cyclic loading conditions are commonly encountered in the applications of shape memory polymers (SMPs), where the cyclic characteristics of the materials determine their performance during the service life, such as deformation resistance, shape recovery speed and shape recovery ratio.

scholarly journals The Influence of Water and Solvent Uptake on Functional Properties of Shape-Memory Polymers

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Ehsan Ghobadi ◽  
Axel Marquardt ◽  
Elias Mahmoudinezhad Zirdehi ◽  
Klaus Neuking ◽  
Fathollah Varnik ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Holding Time ◽  
Fickian Diffusion ◽  
Recovery Ratio ◽  
Solvent Uptake ◽  
Time Shape ◽  
Influence Of Water ◽  
Shape Fixity

In this contribution, diffusion of water, acetone, and ethanol into a polymer matrix has been studied experimentally and numerically by finite element approaches. Moreover, the present study reports an assessment of different thermomechanical conditions of the shape-memory (SM) performance, for example, stress- or strain-holding times in stress- or strain-controlled thermomechanical cycles and the effect of maximum strain. According to the results presented here, the uptake of acetone in Estane is much higher than ethanol and follows classical Fickian diffusion. Further, a series of thermomechanical measurements conducted on dry and physically (hydrolytically) aged polyether urethanes revealed that incorporation of water seems to have an appreciable impact on the shape recovery ratios which can be attributed to the additional physical crosslinks. However, no obvious difference in shape fixation of dry and physically (hydrolytically) aged samples could be recognized. Furthermore, by decreasing the strain-holding time, shape recovery improves significantly. Moreover, the shape fixity is found to be independent of holding time. The shape recovery ratio decreased dramatically with an increase in the stress-holding time.

Shape Recovery Characteristics of Shape Memory Polymers Subjected to Bending

2013 ◽  
Vol 834-836 ◽  
pp. 160-164 ◽  
Author(s):  
Tao Zhou ◽  
Hui Feng Tan ◽  
Yu Yan Liu
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Recovery Ratio ◽  
Thin Sample ◽  
Ratio Measurement ◽  
Series Of Experiments ◽  
Finite Bending ◽  
Important Basis

Shape recovery is a critical characterization of the Shape Memory Polymers (SMP); so far, there has not been a set of uniform specifications, however, on the deformation recovery characterization of SMP, more exactly, on the shape recovery ratio measurement. A simple and effective experimental method is designed to obtain the shape recovery ratio of SMP; and a series of experiments are carried out to measure the shape recovery ratio of a thermoset shape-memory epoxy resin within the finite bending deformation at various test temperatures. And the results show that the shape recovery ratio and rate of the thin sample are larger than that of the thick one; the deformation curvature has little effect on the shape recovery ratio with the test temperatures over, or below, the glass-transition temperature,Tg, but has significant effect nearTg. The conclusions provide an important basis for the structural design of SMP.

scholarly journals Water Triggered Shape Memory Materials

2013 ◽  
Vol 3 (1) ◽  
pp. 49-50 ◽  
Author(s):  
Guoguang Niu
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Electrical Current ◽  
Light Illumination ◽  
Poly Ethylene Glycol ◽  
Thermally Induced ◽  
Permanent Shape ◽  
Poly Ethylene ◽  
Novel Strategy

The term "shape memory effect" refers to the ability of a material to be deformed and fixed into a temporary shape, and to recover its original, permanent shape upon an external stimulus (1). Shape memory polymers have attracted much interest because of their unique properties, and applied tremendously in medical area, such as biodegradable sutures, actuators, catheters and smart stents (2, 3). Shape memory usually is a thermally induced process, although it can be activated by light illumination, electrical current, magnetic, or electromagnetic field (4-6). During the process, the materials are heated directly or indirectly above their glass transition temperature (Tg) or the melting temperature (Tm) in order to recover the original shape. Non-thermally induced shape memory polymers eliminate the temperature constrains and enable the manipulation of the shape recovered under ambient temperature (7, 8). Herein, we report a novel strategy of water induced shape memory, in which the formation and dissolution of poly(ethylene glycol) (PEG) crystal is utilized for the fixation and recovery of temporary deformation of hydrophilic polymer. This water-induced shape recovery is less sensitive to temperature, of which 95% deformation is fixed in circumstance and over 75% recovery is reached even at 0 oC.

scholarly journals A Large-Deformation Theory for Thermally-Actuated Shape-Memory Polymers and its Application

2010 ◽  
Author(s):  
Shawn A. Chester ◽  
Vikas Srivastava ◽  
Claudio V. Di Leo ◽  
Lallit Anand
Keyword(s):  
Glass Transition ◽  
Shape Memory ◽  
Deformation Theory ◽  
Shape Recovery ◽  
Large Deformations ◽  
Shape Memory Polymers ◽  
The Body ◽  
Thermally Induced ◽  
Thermally Actuated ◽  
Common Shape

The most common shape-memory polymers are those in which the shape-recovery is thermally-induced. A body made from such a material may be subjected to large deformations at an elevated temperature above its glass transition temperature &Vthgr;g. Cooling the deformed body to a temperature below &Vthgr;g under active kinematical constraints fixes the deformed shape of the body. The original shape of the body may be recovered if the material is heated back to a temperature above &Vthgr;g without the kinematical constraints. This phenomenon is known as the shape-memory effect. If the shape recovery is partially constrained, the material exerts a recovery force and the phenomenon is known as constrained-recovery.

Relationship between Annealing and Shape Memory Effect of Shape Memory Polyurethane

2014 ◽  
Vol 936 ◽  
pp. 140-144 ◽  
Author(s):  
Jia Ying ◽  
Masaaki Nishikawa ◽  
Masaki Hojo
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Shape Recovery ◽  
Length Change ◽  
Recovery Ratio ◽  
High Entropy ◽  
Change Of State ◽  
Relationship Of ◽  
Shape Memory Polyurethane

The relationship of annealing and shape memory effect of uniaxially oriented shape memory polyurethane was studied; meanwhile a new method of adjusting shape recovery ratio by annealing was proposed for further consideration. Experiments were designed to compare the influence on length change from annealing and shape memory effect with shape memory polyurethane film at 65°C. We found that for shape memory polyurethane which had residual strain from material processing procedure, annealing and shape memory effect have the same effect on its length change if they are both carried out at the same temperature. It is because annealing and shape memory effect have the same mechanism, which is the change of state from low conformational entropy states to the recovery of a stable high entropy state in the polymer. Moreover, it is proved by experiment that shape recovery ratio of shape memory polyurethane can be adjusted by annealing.

scholarly journals Bio-Based Epoxy Shape-Memory Thermosets from Triglycidyl Phloroglucinol

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 542 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Francesc Ferrando ◽  
Àngels Serra ◽  
Silvia De la Flor
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Memory Performance ◽  
Crosslinking Agent ◽  
Shape Memory Polymers ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Partial Substitution ◽  
Scanning Calorimetry

A series of bio-based epoxy shape-memory thermosetting polymers were synthesized starting from a triglycidyl phloroglucinol (3EPOPh) and trimethylolpropane triglycidyl ether (TPTE) as epoxy monomers and a polyetheramine (JEF) as crosslinking agent. The evolution of the curing process was studied by differential scanning calorimetry (DSC) and the materials obtained were characterized by means of DSC, thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), stress-strain tests, and microindentation. Shape-memory properties were evaluated under free and totally constrained conditions. All results were compared with an industrial epoxy thermoset prepared from standard diglycidyl ether of Bisphenol A (DGEBA). Results revealed that materials prepared from 3EPOPh were more reactive and showed a tighter network with higher crosslinking density and glass transition temperatures than the prepared from DGEBA. The partial substitution of 3EPOPh by TPTE as epoxy comonomer caused an increase in the molecular mobility of the materials but without worsening the thermal stability. The shape-memory polymers (SMPs) prepared from 3EPOPh showed good mechanical properties as well as an excellent shape-memory performance. They showed almost complete shape-recovery and shape-fixation, fast shape-recovery rates, and recovery stress up to 7 MPa. The results obtained in this study allow us to conclude that the triglycidyl phloroglucinol derivative of eugenol is a safe and environmentally friendly alternative to DGEBA for preparing thermosetting shape-memory polymers.

scholarly journals Nanoscale Mechanical Properties of Nanoindented Ni48.8Mn27.2Ga24 Ferromagnetic Shape Memory Thin Film

Scanning ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-5
Author(s):  
Xiaofei Fu ◽  
Chao Liu ◽  
Xili Lu ◽  
Xianli Li ◽  
Jingwei Lv ◽  
...  
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Martensitic Transformation ◽  
Magnetron Sputtering ◽  
Shape Memory ◽  
Room Temperature ◽  
Shape Recovery ◽  
Recovery Ratio ◽  
Dc Magnetron Sputtering ◽  
Ferromagnetic Shape Memory

The structure and nanoscale mechanical properties of Ni48.8Mn27.2Ga24 thin film fabricated by DC magnetron sputtering are investigated systematically. The thin film has the austenite state at room temperature with the L21 Hesuler structure. During nanoindentation, stress-induced martensitic transformation occurs on the nanoscale for the film annealed at 823 K for 1 hour and the shape recovery ratio is up to 85.3%. The associated mechanism is discussed.

Deployable Process Analysis of Packaged SMP Sandwich Beam

2010 ◽  
Vol 123-125 ◽  
pp. 943-946 ◽  
Author(s):  
Zheng Fa Li ◽  
Zheng Dao Wang
Keyword(s):  
Shape Memory Alloys ◽  
Shape Memory ◽  
Sandwich Structure ◽  
Shape Recovery ◽  
Process Analysis ◽  
Sandwich Beam ◽  
Shape Memory Polymers ◽  
Recovery Stress ◽  
Recovery Response

Shape memory polymers own many advantages compared with traditional shape memory alloys or ceramics. In order to improve their shape recovery stress and realize a stable recovery response during the deployable process, the structure of SMP sandwich beam composed of two metallic skin and one SMP core is considered. The recovery behaviors of pure SMP and SMP beams reinforced by one-layer metallic skin are also discussed for comparison. The results confirm that the deployable properties of SMP matrix can be significantly improved by using sandwich structure.

Additive manufacturing of shape memory polymers: effects of print orientation and infill percentage on shape memory recovery properties

2020 ◽  
Vol 26 (9) ◽  
pp. 1593-1602
Author(s):  
Jorge Villacres ◽  
David Nobes ◽  
Cagri Ayranci
Keyword(s):  
Additive Manufacturing ◽  
Shape Memory ◽  
Shape Recovery ◽  
Fused Deposition Modeling ◽  
Large Strain ◽  
Shape Memory Polymers ◽  
Polymeric Materials ◽  
Content Type ◽  
Fused Deposition ◽  
Memory Recovery

Purpose The purpose of this paper is to study the shape memory properties of SMP samples produced through a MEAM process. Fused deposition modeling or, as it will be referred to in this paper, material extrusion additive manufacturing (MEAM) is a technique in which polymeric materials are extruded though a nozzle creating parts via accumulation and joining of different layers. These layers are fused together to build three-dimensional objects. Shape memory polymers (SMP) are stimulus responsive materials, which have the ability to recover their pre-programmed form after being exposed to a large strain. To induce its shape memory recovery movement, an external stimulus such as heat needs to be applied. Design/methodology/approach This project investigates and characterizes the influence of print orientation and infill percentage on shape recovery properties. The analyzed shape recovery properties are shape recovery force, shape recovery speed and time elapsed before activation. To determine whether the analyzed factors produce a significant variation on shape recovery properties, t-tests were performed with a 95% confidence factor between each analyzed level. Findings Results proved that print angle and infill percentage do have a significant impact on recovery properties of the manufactured specimens. Originality/value The manufacturing of SMP objects through a MEAM process has a vast potential for different applications; however, the shape recovery properties of these objects need to be analyzed before any practical use can be developed. These have not been studied as a function of print parameters, which is the focus of this study.

Sign in / Sign up

Export Citation Format

Share Document