Self-formation of thickness tunable Bi2Te3 nanoplates on thin films with enhanced thermoelectric performance

RSC Advances ◽  
2016 ◽  
Vol 6 (38) ◽  
pp. 31668-31674 ◽  
Author(s):  
Shuai Liu ◽  
Nan Peng ◽  
Yu Bai ◽  
Dayan Ma ◽  
Fei Ma ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Bismuth Telluride ◽  
Thermoelectric Performance ◽  
Flexible Substrates ◽  
Different Temperatures ◽  
Self Formation

Bismuth telluride thin films were prepared on flexible substrates by magnetron sputtering and then annealed at different temperatures.

scholarly journals Residual Oxygen Effects on the Properties of MoS2 Thin Films Deposited at Different Temperatures by Magnetron Sputtering

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1183
Author(s):  
Peiyu Wang ◽  
Xin Wang ◽  
Fengyin Tan ◽  
Ronghua Zhang
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Deposition Rate ◽  
Deposition Temperature ◽  
Energy Dispersive Spectrometer ◽  
Rf Magnetron Sputtering ◽  
Glass Substrates ◽  
Different Temperatures ◽  
Oxygen Atoms

Molybdenum disulfide (MoS2) thin films were deposited at different temperatures (150 °C, 225 °C, 300 °C, 375 °C, and 450 °C) on quartz glass substrates and silicon substrates using the RF magnetron sputtering method. The influence of deposition temperature on the structural, optical, electrical properties and deposition rate of the obtained thin films was investigated by X-ray diffraction (XRD), Energy Dispersive Spectrometer (EDS), Raman, absorption and transmission spectroscopies, a resistivity-measuring instrument with the four-probe method, and a step profiler. It was found that the MoS2 thin films deposited at the temperatures of 150 °C, 225 °C, and 300 °C were of polycrystalline with a (101) preferred orientation. With increasing deposition temperatures from 150 °C to 300 °C, the crystallization quality of the MoS2 thin films was improved, the Raman vibrational modes were strengthened, the deposition rate decreased, and the optical transmission and bandgap increased. When the deposition temperature increased to above 375 °C, the molecular atoms were partially combined with oxygen atoms to form MoO3 thin film, which caused significant changes in the structural, optical, and electrical properties of the obtained thin films. Therefore, it was necessary to control the deposition temperature and reduce the contamination of oxygen atoms throughout the magnetron sputtering process.

The Effects of the Carrier Concentrations on the Hall Mobilities of ZnO:Al Thin Films Deposited by Magnetron Sputtering

2017 ◽  
Vol 727 ◽  
pp. 938-941
Author(s):  
Xiao Jing Wang ◽  
Yun Zhang
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Magnetron Sputtering ◽  
Carrier Concentration ◽  
Carrier Mobility ◽  
Impurity Scattering ◽  
Flexible Substrates ◽  
Boundary Scattering ◽  
Scattering Mechanism ◽  
Ionized Impurity Scattering

ZnO:Al thin films were deposited on flexible substrates by magnetron sputtering. The effects of the carrier concentrations on the hall mobilities of AZO films were investigated. When the carrier concentration was high (~1020/cm3), the hall mobility decreased with increase of the carrier concentration, showing obvious characteristics of ionized impurity scattering; moreover, the carrier mobility could be expressed to be-2.14/3 proportional of the carrier concentration by combining the results of simulation and experiments.simulation and experiment. When the carrier concentration was about a magnitude of 1019 cm-3, the carrier mobility is influenced by the carrier concentration and grain size, which means the carrier mobility was affected by both the grain boundary scattering and ionized purity scattering mechanism.

The Preparation of ZnO: Al Thin Films on Flexible Substrates by Magnetron Sputtering Method

2014 ◽  
Vol 989-994 ◽  
pp. 65-68
Author(s):  
Xiao Jing Wang
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Buffer Layer ◽  
Compressive Stress ◽  
Lattice Constant ◽  
Rf Magnetron Sputtering ◽  
Hexagonal Structure ◽  
Preferred Orientation ◽  
Flexible Substrates ◽  
Average Transmittance

ZnO: Al film was deposited on TPT substrate with SiO2 buffer layer by RF magnetron sputtering. The obtained film had a hexagonal structure and highly (002) preferred orientation. The lattice constant distortion of the film with buffer layer was decreased and the compressive stress was 0.779GPa. The carrier concentratio reached to 3.15×10+20/cm3. The resistivity of ZAO film with SiO2 buffer layer was about 9.2×10-3 Ω·cm and the average transmittance was over 72% in the range of 380~900nm.

The Influence of Substrate Temperature on the Morphological and Optical Properties of ZnTiO3 Thin Films Prepared by Magnetron Sputtering

2013 ◽  
Vol 804 ◽  
pp. 3-7
Author(s):  
Chao Zhan ◽  
Wen Jian Ke ◽  
Xin Ming Li ◽  
Wan Li Du ◽  
Li Juan Wang ◽  
...  
Keyword(s):  
Thin Films ◽  
Surface Roughness ◽  
Refractive Index ◽  
Optical Properties ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Dispersion Model ◽  
Film Surface ◽  
Cubic Phase ◽  
Different Temperatures

Cubic ZnTiO3thin films have been prepared by radio frequency magnetron sputtering on n-type (100) Si substrate at different temperatures. The morphological and optical properties of ZnTiO3films in relation to substrate temperatures are investigated by spectroscopic ellipsometry (SE) and AFM as well as SEM in detail. X-ray diffraction (XRD) measurement shows that all the films have a cubic phase structure and the optimum substrate temperature to form crystalline ZnTiO3thin film is 250 °C. Through SEM and AFM, the particle size in thin films and film surface roughness increase with increasing the substrate temperature. Based on a parameterized TaucLorentz dispersion model, the optical constants and surface roughness of ZnTiO3films related to the substrate temperature are systematically extracted by SE measurement. The surface roughness of the film measured from AFM agrees well with result extracted from SE, which proved that the established SE model is reasonable. With increasing substrate temperature, the refractive index decreases and the main factor in determining the refractive index was deduced to be the surface roughness related to the film packing density. The extinction coefficient of the samples is close to zero, but increases slightly with the increase of the substrate temperature, which is due to the enhancement of scattering effect in the crystalline ZnTiO3film.

Sign in / Sign up

Export Citation Format

Share Document