High speed, high temperature electrical characterization of phase change materials: metastable phases, crystallization dynamics, and resistance drift

Nanoscale ◽  
2015 ◽  
Vol 7 (40) ◽  
pp. 16625-16630 ◽  
Author(s):  
Faruk Dirisaglik ◽  
Gokhan Bakan ◽  
Zoila Jurado ◽  
Sadid Muneer ◽  
Mustafa Akbulut ◽  
...  
Keyword(s):  
High Temperature ◽  
Phase Change ◽  
High Speed ◽  
Phase Change Materials ◽  
Electrical Characterization ◽  
Metastable Phases ◽  
Crystallization Dynamics

scholarly journals Experimental Characterization of Phase Change Materials for Refrigeration Processes

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3033
Author(s):  
Anastasia Stamatiou ◽  
Lukas Müller ◽  
Roger Zimmermann ◽  
Jamie Hillis ◽  
David Oliver ◽  
...  
Keyword(s):  
Energy Density ◽  
Phase Change ◽  
Thermophysical Properties ◽  
Phase Change Materials ◽  
Cost Effective ◽  
Latent Heat Storage ◽  
Lower Energy Density ◽  
Change Material ◽  
Storage Units

Latent heat storage units for refrigeration processes are promising as alternatives to water/glycol-based storage due to their significantly higher energy densities, which would lead to more compact and potentially more cost-effective storages. In this study, important thermophysical properties of five phase change material (PCM) candidates are determined in the temperature range between −22 and −35 °C and their compatibility with relevant metals and polymers is investigated. The goal is to complement existing scattered information in literature and to apply a consistent testing methodology to all PCMs, to enable a more reliable comparison between them. More specifically, the enthalpy of fusion, melting point, density, compatibility with aluminum, copper, polyethylene (PE), polypropylene (PP), neoprene and butyl rubber, are experimentally determined for 1-heptanol, n-decane, propionic acid, NaCl/water mixtures, and Al(NO3)3/water mixtures. The results of the investigations reveal individual strengths and weaknesses of the five candidates. Further, 23.3 wt.% NaCl in water stands out for its very high volumetric energy density and n-decane follows with a lower energy density but better compatibility with surrounding materials and supercooling performance. The importance of using consistent methodologies to determine thermophysical properties when the goal is to compare PCM performance is highlighted.

scholarly journals Characterization of Unripe and Mature Avocado Seed Oil in Different Proportions as Phase Change Materials and Simulation of Their Cooling Storage

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 107
Author(s):  
Evelyn Reyes-Cueva ◽  
Juan Francisco Nicolalde ◽  
Javier Martínez-Gómez
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Seed Oil ◽  
Energy System ◽  
Maturity Stage ◽  
Natural Environments ◽  
Renewable Materials ◽  
Scanning Calorimetry ◽  
Avocado Seed

Environmental problems have been associated with energy consumption and waste management. A solution is the development of renewable materials such as organic phase change materials. Characterization of new materials allows knowing their applications and simulations provide an idea of how they can developed. Consequently, this research is focused on the thermal and chemical characterization of five different avocado seed oils depending on the maturity stage of the seed: 100% unripe, 25% mature-75% unripe, 50% mature-50% unripe, 75% mature-25% unripe, and 100% mature. The characterization was performed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The best oil for natural environments corresponded to 100% matured seed with an enthalpy of fusion of 52.93 J·g−1, and a degradation temperature between 241–545 °C. In addition, the FTIR analysis shows that unripe seed oil seems to contain more lipids than a mature one. Furthermore, a simulation with an isothermal box was conducted with the characterized oil with an initial temperature of −14 °C for the isothermal box, −27 °C for the PCM box, and an ambient temperature of 25 °C. The results show that without the PCM the temperature can reach −8 °C and with it is −12 °C after 7 h, proving its application as a cold thermal energy system.

scholarly journals Influence of Adding Encapsulated Phase Change Materials in Aerial Lime Based Mortars

2013 ◽  
Vol 687 ◽  
pp. 255-261 ◽  
Author(s):  
Sandra Cunha ◽  
José Barroso Aguiar ◽  
Victor Ferreira ◽  
António Tadeu
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Renewable Energy Sources ◽  
High Growth ◽  
High Energy ◽  
High Growth Rate ◽  
Aesthetic Appearance ◽  
Hardened State ◽  
High Energy Consumption

Increasingly in a society with a high growth rate and standards of comfort, the need to minimize the currently high energy consumption by taking advantage of renewable energy sources arises. The mortars with incorporation of phase change materials (PCM) have the ability to regulate the temperature inside buildings, contributing for an increase in the level of thermal comfort and reduction of the use of heating, ventilation and air conditioning (HVAC) equipment, using only the energy supplied by the sun. However, the incorporation of PCM in mortars modifies some of its characteristics. Therefore, the main objective of this study was the characterization of mortars doped with two different phase change materials. Specific properties of different PCM, such as particle size, shape and enthalpy were studied, as well as the properties of the fresh and hardened state of these mortars. Nine different compositions were developed which were initially doped with microcapsules of PCM A and subsequently doped with microcapsules of PCM B. It was possible to observe that the incorporation of phase change materials in mortars causes differences in properties such as compressive strength, flexural strength and shrinkage. After the study of the behaviour of these mortars with the incorporation of two different phase change materials, it was possible to select the composition with a better compromise between its aesthetic appearance, physical and mechanical characteristics.

Synthesis and Characterization of Comb-like P(MPEGA-co-AM) Copolymer as Phase Change Materials

2012 ◽  
Vol 30 (9) ◽  
pp. 2247-2251 ◽  
Author(s):  
Hengxue Xiang ◽  
Shaohua Chen ◽  
Shichao Wang ◽  
Cheng Peng ◽  
Meifang Zhu
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Synthesis And Characterization
Sign in / Sign up

Export Citation Format

Share Document