ADH-catalysed hexanol oxidation with fully integrated NADH regeneration performed in microreactors connected in series

RSC Advances ◽  
2014 ◽  
Vol 4 (79) ◽  
pp. 41714-41721 ◽  
Author(s):  
Anita Šalić ◽  
Bruno Zelić
Keyword(s):  
Nadh Regeneration ◽  
Fully Integrated ◽  
In Series ◽  
Hexanol Oxidation

scholarly journals An Integrated Switch in a HV-SOI Wafer Technology, With a Novel Self-Protection Mechanism

2010 ◽  
Vol 5 (1) ◽  
pp. 7-15
Author(s):  
Matías Miguez ◽  
Joel Gak ◽  
Alfredo Arnaud
Keyword(s):  
Supply Voltage ◽  
Cmos Technology ◽  
Implantable Medical Devices ◽  
Fully Integrated ◽  
Protection Mechanism ◽  
Expected Performance ◽  
In Series ◽  
Safety Considerations ◽  
Low Supply Voltage ◽  
Self Protection

An integrated switch to control electrical stimuli in implantable medical devices is presented. First a self-biased protection mechanism to avoid VGS reaching maximum rated value is presented. Then, using a HV-CMOS technology this technique is incorporated in a fully integrated switch, to control 0 to 16V, and 0 to 30 mA, pulses for implantable stimulators. Because of the low supply voltage VDD between 2 to 5V, and safety considerations in implantable devices, special level shifters, drivers, and a voltage multiplier, that drive a large 40000μm/3μm dual-in-series PMOS switch, were necessary for the circuit. The circuit was fabricated in a HV 0.6μm CMOS technology in SOI wafer for transistor isolation, and tested. Measurement results that closely fit the expected performance of the circuit are presented.

FR-IR Molecular Microanalysis System

1990 ◽  
Vol 48 (2) ◽  
pp. 270-271
Author(s):  
John A. Reffner ◽  
William T. Wihlborg
Keyword(s):  
Fourier Transform ◽  
Fourier Transform Infrared ◽  
Integrated System ◽  
Morphological Examination ◽  
Fully Integrated ◽  
Ir Microscopy ◽  
Normal Functions ◽  
Infrared Microspectroscopy ◽  
Infrared Spectral ◽  
Ft Ir

The IRμs™ is the first fully integrated system for Fourier transform infrared (FT-IR) microscopy. FT-IR microscopy combines light microscopy for morphological examination with infrared spectroscopy for chemical identification of microscopic samples or domains. Because the IRμs system is a new tool for molecular microanalysis, its optical, mechanical and system design are described to illustrate the state of development of molecular microanalysis. Applications of infrared microspectroscopy are reviewed by Messerschmidt and Harthcock.Infrared spectral analysis of microscopic samples is not a new idea, it dates back to 1949, with the first commercial instrument being offered by Perkin-Elmer Co. Inc. in 1953. These early efforts showed promise but failed the test of practically. It was not until the advances in computer science were applied did infrared microspectroscopy emerge as a useful technique. Microscopes designed as accessories for Fourier transform infrared spectrometers have been commercially available since 1983. These accessory microscopes provide the best means for analytical spectroscopists to analyze microscopic samples, while not interfering with the FT-IR spectrometer’s normal functions.

The Shikani HME: A New Tracheostomy Heat and Moisture Exchanger

2020 ◽  
Vol 63 (9) ◽  
pp. 2921-2929
Author(s):  
Alan H. Shikani ◽  
Elamin M. Elamin ◽  
Andrew C. Miller
Keyword(s):  
Ex Vivo ◽  
Moisture Loss ◽  
Speaking Valve ◽  
Time Zero ◽  
In Series ◽  
Turbulent Airflow ◽  
The Difference ◽  
Loss Efficiency ◽  
Heat And Moisture ◽  
Lung Simulation

Purpose Tracheostomy patients face many adversities including loss of phonation and essential airway functions including air filtering, warming, and humidification. Heat and moisture exchangers (HMEs) facilitate humidification and filtering of inspired air. The Shikani HME (S-HME) is a novel turbulent airflow HME that may be used in-line with the Shikani Speaking Valve (SSV), allowing for uniquely preserved phonation during humidification. The aims of this study were to (a) compare the airflow resistance ( R airflow ) and humidification efficiency of the S-HME and the Mallinckrodt Tracheolife II tracheostomy HME (M-HME) when dry (time zero) and wet (after 24 hr) and (b) determine if in-line application of the S-HME with a tracheostomy speaking valve significantly increases R airflow over a tracheostomy speaking valve alone (whether SSV or Passy Muir Valve [PMV]). Method A prospective observational ex vivo study was conducted using a pneumotachometer lung simulation unit to measure airflow ( Q ) amplitude and R airflow , as indicated by a pressure drop ( P Drop ) across the device (S-HME, M-HME, SSV + S-HME, and PMV). Additionally, P Drop was studied for the S-HME and M-HME when dry at time zero (T 0 ) and after 24 hr of moisture testing (T 24 ) at Q of 0.5, 1, and 1.5 L/s. Results R airflow was significantly less for the S-HME than M-HME (T 0 and T 24 ). R airflow of the SSV + S-HME in series did not significant increase R airflow over the SSV or PMV alone. Moisture loss efficiency trended toward greater efficiency for the S-HME; however, the difference was not statistically significant. Conclusions The turbulent flow S-HME provides heat and moisture exchange with similar or greater efficacy than the widely used laminar airflow M-HME, but with significantly lower resistance. The S-HME also allows the innovative advantage of in-line use with the SSV, hence allowing concurrent humidification and phonation during application, without having to manipulate either device.

Status of nondestructive control of transport function metal products at JSC EVRAZ NTMK

2020 ◽  
Vol 76 (6) ◽  
pp. 586-590
Author(s):  
S. P. Bersenev ◽  
E. M. Slobtsova
Keyword(s):  
Crack Detection ◽  
Middle Part ◽  
Control Line ◽  
Magnetic Powder ◽  
Nondestructive Control ◽  
Automated Control ◽  
Ultrasonic Control ◽  
Acoustic Contact ◽  
In Series

Achievements in the area of automated ultrasonic control of quality of rails, solid-rolled wheels and tyres, wheels magnetic powder crack detection, carried out at JSC EVRAZ NTMK. The 100% nondestructive control is accomplished by automated control in series at two ultrasonic facilities RWI-01 and four facilities УМКК-1 of magnetic powder control, installed into the exit control line in the wheel-tyre shop. Diagram of location, converters displacement and control operations in the process of control at the facility RWI-01 presented, as well as the structural diagram of the facility УМКК-1. The automated ultrasonic control of rough tyres is made in the tyres control line of the wheel-tyre shop at the facility УКБ-1Д. The facility enables to control internal defects of tyres in radial, axis and circular directions of radiation. Possibilities of the facility УКБ-1Д software were shown. Nondestructive control of railway rails is made at two facilities, comprising the automated control line of the rail and structural shop. The УКР-64Э facility of automated ultrasonic rails control is intended to reveal defects in the area of head, web and middle part of rail foot by pulse echo-method with a immersion acoustic contact. The diagram of rail P65 at the facility УКР-64Э control presented. To reveal defects of the macrostructure in the area of rail head and web by mirror-shadow method, an ultrasonic noncontact electromagnetic-acoustic facility is used. It was noted, that implementation of the 100% nondestructive control into the technology of rolled stuff production enabled to increase the quality of products supplied to customers and to increase their competiveness.

Dimensions of plane and solid angles and their units in the International System of Units (SI)

2020 ◽  
pp. 26-32
Author(s):  
M. I. Kalinin ◽  
L. K. Isaev ◽  
F. V. Bulygin
Keyword(s):  
Solid Angle ◽  
International System ◽  
International Committee ◽  
Plane Angle ◽  
Arc Length ◽  
Weights And Measures ◽  
International System Of Units ◽  
System Of Units ◽  
In Series ◽  
Solid Angles

The situation that has developed in the International System of Units (SI) as a result of adopting the recommendation of the International Committee of Weights and Measures (CIPM) in 1980, which proposed to consider plane and solid angles as dimensionless derived quantities, is analyzed. It is shown that the basis for such a solution was a misunderstanding of the mathematical formula relating the arc length of a circle with its radius and corresponding central angle, as well as of the expansions of trigonometric functions in series. From the analysis presented in the article, it follows that a plane angle does not depend on any of the SI quantities and should be assigned to the base quantities, and its unit, the radian, should be added to the base SI units. A solid angle, in this case, turns out to be a derived quantity of a plane angle. Its unit, the steradian, is a coherent derived unit equal to the square radian.

Solar Power Conditioners Using Bidirectional Chopper Circuits Connected in Series

2012 ◽  
Vol 132 (1) ◽  
pp. 50-57 ◽  
Author(s):  
Hideaki Fujita ◽  
Masao Mabuchi ◽  
Yasuhiro Tsubota ◽  
Takao Mizogami
Keyword(s):  
Solar Power ◽  
In Series

Substantiation of safe underground mining in series of coal seams under hydraulic fill

2018 ◽  
Vol 8 ◽  
pp. 217-226
Author(s):  
Yu.I. Kutepov ◽  
◽  
A.S. Mironov ◽  
Yu.Yu. Kutepov ◽  
M.V. Sablin ◽  
...  
Keyword(s):  
Underground Mining ◽  
Coal Seams ◽  
Hydraulic Fill ◽  
In Series
Sign in / Sign up

Export Citation Format

Share Document