Effect of cold plasma treatment on surface properties and gas permeability of polyimide films

RSC Advances ◽  
2014 ◽  
Vol 4 (59) ◽  
pp. 31036-31046 ◽  
Author(s):  
Kateryna Fatyeyeva ◽  
Abdellatif Dahi ◽  
Corinne Chappey ◽  
Dominique Langevin ◽  
Jean-Marc Valleton ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Cold Plasma ◽  
Gas Permeability ◽  
Gas Permeation ◽  
Polyimide Films ◽  
Water Contact ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
The Relationship ◽  
Radio Frequency Discharge

Surface functionalization of polyimide films was carried out by cold plasma treatment using a radio frequency discharge and the optimum plasma conditions were evaluated by water contact angle measurements. The relationship between gas permeation behaviour and surface modification of the films was discussed.

scholarly journals Improved de-inking of inkjet-printed paper using environmentally friendly atmospheric pressure low temperature plasma for paper recycling

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Rodolphe Mauchauffé ◽  
Seung Jun Lee ◽  
Isaac Han ◽  
Sang Hyeong Kim ◽  
Se Youn Moon
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Paper Recycling ◽  
Temperature Plasma ◽  
Water Contact ◽  
Angle Measurements ◽  
Natural Energy ◽  
Contact Angle Measurements ◽  
Speed Up ◽  
Uv Visible

Abstract Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

scholarly journals Surface Characterisation of PEEK and Dentin, Treated with Atmospheric Non-Thermal PDD Plasma, Applicable for Dental Chair-Side Procedures

Plasma ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 389-398
Author(s):  
Marius Behnecke ◽  
Vincent Steinert ◽  
Svea Petersen
Keyword(s):  
Contact Angle ◽  
Phosphoric Acid ◽  
Plasma Treatment ◽  
Water Contact Angle ◽  
Acid Etching ◽  
Water Contact ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Dentin Tubules ◽  
Phosphoric Acid Etching

This study investigates the suitability of Piezoelectric Direct Discharge Plasma as a tool for wetting behaviour modification of PEEK and dentin, and compares the results of this method with low-pressure plasma treatment and phosphoric acid etching. Static contact angle measurements were made, roughness was assessed using tactile measurement, and AFM and SEM images were taken. An optimum operating distance of ≤15 mm was determined for the plasma based on the water contact angle. Furthermore, it was demonstrated that despite only a fraction of the power, the PDD plasma also produces hydrophilic and nanostructured PEEK surfaces with a 38° water contact angle in the same plasma time. In contrast, the gold standard of dental surface modification of dentin—phosphoric acid etching—showed no measurable contact angle due to the exposed dentin tubules. Treatment with PDD plasma reduces the water contact angle of dentin from 65° to 43° and is not negative affected by water. Wet, PDD plasma-treated dentin samples show a water contact angle of only 26.5°. The dentin tubules exposed by chemical etching led to a significantly increased roughness. No comparable effect could be demonstrated for plasma treatment on dentin, but based on the contact angle measurements, a chemically strongly activated surface with strongly polar interaction behaviour can be assumed. The additional use of the PDD plasma technique to improve wetting could therefore have a positive effect on the adhesive bond between human dentin and polymeric dental restorative materials or, depending on the adhesive system, replace the etching process altogether.

Preparation Of Moisture Resistant Polylmide Films By Plasma Treatment

1991 ◽  
Vol 227 ◽  
Author(s):  
Mark A. Petrich ◽  
Hsueh Yi Lu
Keyword(s):  
Plasma Treatment ◽  
Photoelectron Spectroscopy ◽  
Polymeric Materials ◽  
Moisture Resistance ◽  
Polyimide Films ◽  
Water Contact ◽  
Angle Measurements ◽  
Materials Used ◽  
Microelectronics Fabrication ◽  
Processing Techniques

ABSTRACTPolyimides are an important class of polymeric materials used in microelectronics fabrication. These polymers could be used even more extensively if it were possible to improve their moisture resistance. We are using plasma processing techniques to modify the moisture resistance of polyimide films. Films are exposed to nitrogen trifluoride plasmas to introduce fluorine into the surface of the polyimide. Fluorination is monitored with x-ray photoelectron spectroscopy and Fourier transform infrared absorption spectroscopy. Water contact angle measurements are used to assess the hydrophobicity of the treated surfaces. Thus far, we have demonstrated that this plasma treatment is a good way of introducing fluorine into the polyimide surface, and that these treatments do enhance the hydrophobic nature of polyimide.

Nanostructured Polymer Brushes With Reversibly Changing Properties

2002 ◽  
Vol 727 ◽  
Author(s):  
Denys Usov ◽  
Manfred Stamm ◽  
Sergiy Minko ◽  
Christian Froeck ◽  
Andreas Scholl ◽  
...  
Keyword(s):  
Polymer Brushes ◽  
Phase Segregation ◽  
Water Contact ◽  
Angle Measurements ◽  
Nanostructured Polymer ◽  
Contact Angle Measurements ◽  
Vertical Segregation ◽  
Oxygen Plasma Etching ◽  
Grafting From ◽  
Photoemission Electron

AbstractWe investigated the interplay between different mechanisms of the lateral and vertical segregation in the synthesized via “grafting from” approach symmetric A/B (where A and B are poly(styrene-co-2,3,4,5,6-pentafluorostyrene) and poly(methylmethacrylate), respectively) polymer brushes upon exposure to different solvents. We used X-ray photoemission electron spectroscopy and microscopy (X-PEEM), AFM, water contact angle measurements, and oxygen plasma etching to study morphology of the brushes. The ripple morphology after toluene (nonselective solvent) revealed elongated lamellar-like domains of A and B polymers alternating across the surface. The dimple-A morphology consisting of round clusters of the polymer A was observed after acetone (selective solvent for B). The top layer was enriched with the polymer B showing that the brush underwent both the lateral and vertical phase segregation. A qualitative agreement with predictions of SCF theory was found.

scholarly journals Epoxy/alumina composite coating on welded steel 316L with excellent wear and anticorrosion properties

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Maryama Hammi ◽  
Younes Ziat ◽  
Zakaryaa Zarhri ◽  
Charaf Laghlimi ◽  
Abdelaziz Moutcine
Keyword(s):  
Electrochemical Behaviour ◽  
Sem Analysis ◽  
Water Contact ◽  
Welded Steel ◽  
Melted Zone ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Alumina Composite ◽  
The Cost ◽  
Good Contrast

AbstractThe main purpose of this study is to elaborate anticorrosive coatings for the welded steel 316L, since this later is widely used in industrial field. Hence, within this work we have studied the electrochemical behaviour of different zones of the welded steel 316 in 1 M HCl media. The macrography study of the welded steel has revealed the different areas with a good contrast. We have stated three different zones, namely; melted zone (MZ), heat affected zone (HAZ) and base metal zone (BM). Impedance studies on welded steel 316L were conducted in 1 M HCl solution, coating of Epoxy/Alumina composite was applied on different zones, in order to reveal the anti-corrosion efficiency in each zone. Scanning electron microscopy (SEM) analysis was undertaken in order to check how far the used coating in such aggressive media protects the studied zones and these findings were assessed by water contact angle measurements. The choice of this coating is based on the cost and the safety. We concluded that the Epoxy/Alumina composite has a good protecting effect regarding welded steel in aggressive media.

scholarly journals PLA-Based Hybrid and Composite Electrospun Fibrous Scaffolds as Potential Materials for Tissue Engineering

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Anna Magiera ◽  
Jarosław Markowski ◽  
Elzbieta Menaszek ◽  
Jan Pilch ◽  
Stanislaw Blazewicz
Keyword(s):  
Tissue Engineering ◽  
Mechanical Tests ◽  
Hybrid Structures ◽  
Poly Lactic Acid ◽  
Electrospinning Technique ◽  
Water Contact ◽  
Human Osteoblasts ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Normal Human

The aim of the study was to manufacture poly(lactic acid)- (PLA-) based nanofibrous nonwovens that were modified using two types of modifiers, namely, gelatin- (GEL-) based nanofibres and carbon nanotubes (CNT). Hybrid nonwovens consisting of PLA and GEL nanofibres (PLA/GEL), as well as CNT-modified PLA nanofibres with GEL nanofibres (PLA + CNT/GEL), in the form of mats, were manufactured using concurrent-electrospinning technique (co-ES). The ability of such hybrid structures as potential scaffolds for tissue engineering was studied. Both types of hybrid samples and one-component PLA and CNTs-modified PLA mats were investigated using scanning electron microscopy (SEM), water contact angle measurements, and biological and mechanical tests. The morphology, microstructure, and selected properties of the materials were analyzed. Biocompatibility and bioactivity in contact with normal human osteoblasts (NHOst) were studied. The coelectrospun PLA and GEL nanofibres retained their structures in hybrid samples. Both types of hybrid nonwovens were not cytotoxic and showed better osteoinductivity in comparison to scaffolds made from pure PLA. These samples also showed significantly reduced hydrophobicity compared to one-component PLA nonwovens. The CNT-contained PLA nanofibres improved mechanical properties of hybrid samples and such a 3D system appears to be interesting for potential application as a tissue engineering scaffold.

scholarly journals Synthesis, Hydrophilicity and Micellization of Coil–Brush Polystyrene-b-(polyglycidol-g-polyglycidol) Copolymer—Comparison with Linear Polystyrene-b-Polyglycidol

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 253
Author(s):  
Mariusz Gadzinowski ◽  
Maciej Kasprów ◽  
Teresa Basinska ◽  
Stanislaw Slomkowski ◽  
Łukasz Otulakowski ◽  
...  
Keyword(s):  
Contact Angle ◽  
Self Assembly ◽  
Original Method ◽  
Critical Micellization Concentration ◽  
Water Contact ◽  
1H And 13C Nmr ◽  
Similar Composition ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Static Conditions

In this paper, an original method of synthesis of coil–brush amphiphilic polystyrene-b-(polyglycidol-g-polyglycidol) (PS-b-(PGL-g-PGL)) block copolymers was developed. The hypothesis that their hydrophilicity and micellization can be controlled by polyglycidol blocks architecture was verified. The research enabled comparison of behavior in water of PS-b-PGL copolymers and block–brush copolymers PS-b-(PGL-g-PGL) with similar composition. The coil–brush copolymers were composed of PS-b-PGL linear core with average DPn of polystyrene 29 and 13 of polyglycidol blocks. The DPn of polyglycidol side blocks of coil–b–brush copolymers were 2, 7, and 11, respectively. The copolymers were characterized by 1H and 13C NMR, GPC, and FTIR methods. The hydrophilicity of films from the linear and coil–brush copolymers was determined by water contact angle measurements in static conditions. The behavior of coil–brush copolymers in water and their critical micellization concentration (CMC) were determined by UV-VIS using 1,6-diphenylhexa-1,3,5-trien (DPH) as marker and by DLS. The CMC values for brush copolymers were much higher than for linear species with similar PGL content. The results of the copolymer film wettability and the copolymer self-assembly studies were related to fraction of hydrophilic polyglycidol. The CMC for both types of polymers increased exponentially with increasing content of polyglycidol.

scholarly journals Biomaterial Embedding Process for Ceramic–Polymer Microfluidic Sensors

Sensors ◽  
2020 ◽  
Vol 20 (6) ◽  
pp. 1745 ◽  
Author(s):  
Witold Nawrot ◽  
Karol Malecha
Keyword(s):  
Plasma Treatment ◽  
Anodic Bonding ◽  
Plasma Modification ◽  
Biochemical Processes ◽  
Angle Measurements ◽  
Plasma Activation ◽  
Microfluidic Sensors ◽  
Contact Angle Measurements ◽  
Novel Method ◽  
Sample Structure

One of the major issues in microfluidic biosensors is biolayer deposition. Typical manufacturing processes, such as firing of ceramics and anodic bonding of silicon and glass, involve exposure to high temperatures, which any biomaterial is very vulnerable to. Therefore, current methods are based on deposition from liquid, for example, chemical bath deposition (CBD) and electrodeposition (ED). However, such approaches are not suitable for many biomaterials. This problem was partially resolved by introduction of ceramic–polymer bonding using plasma treatment. This method introduces an approximately 15-min-long window for biomodification between plasma activation and sealing the system with a polymer cap. Unfortunately, some biochemical processes are rather slow, and this time is not sufficient for the proper attachment of a biomaterial to the surface. Therefore, a novel method, based on plasma activation after biomodification, is introduced. Crucially, the discharge occurs selectively; otherwise, it would etch the biomaterial. Difficulties in manufacturing ceramic biosensors could be overcome by selective surface modification using plasma treatment and bonding to polymer. The area of plasma modification was investigated through contact-angle measurements and Fourier-transform infrared (FTIR) analyses. A sample structure was manufactured in order to prove the concept. The results show that the method is viable.

Non-woven Membranes Electrospun from Polylactic Acid Incorporating Silver Nanoparticles as Biocide

2012 ◽  
Vol 1376 ◽  
Author(s):  
Haydee Vargas-Villagran ◽  
Elvia Teran-Salgado ◽  
Maraolina Dominguez-Diaz ◽  
Osvaldo Flores ◽  
Bernardo Campillo ◽  
...  
Keyword(s):  
Contact Angle ◽  
Silver Nanoparticles ◽  
Polylactic Acid ◽  
Chloroform Solution ◽  
Average Diameter ◽  
Electrospinning Process ◽  
Water Contact ◽  
X Ray Scattering ◽  
Angle Measurements ◽  
Contact Angle Measurements

ABSTRACTIn this research, we describe the electrospinning processing of polylactic acid (PLA) and the influence of silver nanoparticles on the morphology and microstructure of produced non woven membranes thus produced. The PLA was electrospun from a chloroform solution and a filamentary and granular morphology was obtained, the filaments having an average diameter of 1.25 μm, When silver nanoparticles (of ca. 12 nm size) were incorporated, the filaments diameter was reduced to an average of 0.65 μm, and the density of beads was also reduced. The membranes were rather amorphous, as revealed by X-ray scattering, presumably due to the quenching process associated with the electrospinning process. Water contact angle measurements showed that silver nanoparticles induced significant hidrophobicity in the membranes as neat PLA membrane had a contact angle of 54° and PLA/Ag membrane exhibited an angle of 115°.

Sign in / Sign up

Export Citation Format

Share Document