Characterization of the spherical intermediates and fibril formation of hCT in HEPES solution using solid-state 13C-NMR and transmission electron microscopy

2013 ◽  
Vol 15 (39) ◽  
pp. 16956 ◽  
Author(s):  
Hikari Itoh-Watanabe ◽  
Miya Kamihira-Ishijima ◽  
Izuru Kawamura ◽  
Masashi Kondoh ◽  
Masamichi Nakakoshi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Solid State ◽  
13C Nmr ◽  
Fibril Formation ◽  
Transmission Electron ◽  
Solid State 13C Nmr

Transmission Electron Microscopy of an Aluminum-Silver-Stainless Steel Solid State Bond

1985 ◽  
Vol 43 ◽  
pp. 172-173
Author(s):  
M. J. Carr ◽  
J. F. Shewbridge ◽  
T. O. Wilford
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Solid State ◽  
Specimen Preparation ◽  
Dimensional Control ◽  
Tem Analysis ◽  
Metal Parts ◽  
Dissimilar Metal ◽  
Transmission Electron ◽  
Short Time

Strong solid state bonds are routinely produced between physical vapor deposited (PVD) silver coatings deposited on sputter cleaned surfaces of two dissimilar metal parts. The low temperature (200°C) and short time (10 min) used in the bonding cycle are advantageous from the standpoint of productivity and dimensional control. These conditions unfortunately produce no microstructural changes at or near the interface that are detectable by optical, SEM, or microprobe examination. Microstructural problems arising at these interfaces could therefore easily go undetected by these techniques. TEM analysis has not been previously applied to this problem because of the difficulty in specimen preparation. The purpose of this paper is to describe our technique for preparing specimens from solid state bonds and to present our initial observations of the microstructural details of such bonds.

Characterization of submicrometer fluid Inclusions in minerals by Analytical/Transmission Electron Microscopy and electron diffraction

1990 ◽  
Vol 48 (4) ◽  
pp. 424-424
Author(s):  
George Guthrie ◽  
David Veblen
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Microscope ◽  
Electron Diffraction ◽  
Light Microscopy ◽  
Fluid Inclusions ◽  
Energy Dispersive Spectrometer ◽  
Analytical Transmission Electron Microscopy ◽  
Transmission Electron

The nature of a geologic fluid can often be inferred from fluid-filled cavities (generally <100 μm in size) that are trapped during the growth of a mineral. A variety of techniques enables the fluids and daughter crystals (any solid precipitated from the trapped fluid) to be identified from cavities greater than a few micrometers. Many minerals, however, contain fluid inclusions smaller than a micrometer. Though inclusions this small are difficult or impossible to study by conventional techniques, they are ideally suited for study by analytical/ transmission electron microscopy (A/TEM) and electron diffraction. We have used this technique to study fluid inclusions and daughter crystals in diamond and feldspar.Inclusion-rich samples of diamond and feldspar were ion-thinned to electron transparency and examined with a Philips 420T electron microscope (120 keV) equipped with an EDAX beryllium-windowed energy dispersive spectrometer. Thin edges of the sample were perforated in areas that appeared in light microscopy to be populated densely with inclusions. In a few cases, the perforations were bound polygonal sides to which crystals (structurally and compositionally different from the host mineral) were attached (Figure 1).

Intergrowth of niobium tungsten oxides of the tetragonal tungsten bronze type

2020 ◽  
Vol 75 (11) ◽  
pp. 913-919
Author(s):  
Frank Krumeich
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Tungsten Bronze ◽  
Structural Complexity ◽  
Dark Field ◽  
Tetragonal Tungsten Bronze ◽  
Tungsten Oxides ◽  
Transmission Electron ◽  
Scanning Transmission

AbstractSince the 1970s, high-resolution transmission electron microscopy (HRTEM) is well established as the most appropriate method to explore the structural complexity of niobium tungsten oxides. Today, scanning transmission electron microscopy (STEM) represents an important alternative for performing the structural characterization of such oxides. STEM images recorded with a high-angle annular dark field (HAADF) detector provide not only information about the cation positions but also about the distribution of niobium and tungsten as the intensity is directly correlated to the local scattering potential. The applicability of this method is demonstrated here for the characterization of the real structure of Nb7W10O47.5. This sample contains well-ordered domains of Nb8W9O47 and Nb4W7O31 besides little ordered areas according to HRTEM results. Structural models for Nb4W7O31 and twinning occurring in this phase have been derived from the interpretation of HAADF-STEM images. A remarkable grain boundary between well-ordered domains of Nb4W7O31 and Nb8W9O47 has been found that contains one-dimensionally periodic features. Furthermore, short-range order observed in less ordered areas could be attributed to an intimate intergrowth of small sections of different tetragonal tungsten bronze (TTB) based structures.

Sign in / Sign up

Export Citation Format

Share Document