High-frequency acoustic waves are not sufficient to heat the solar chromosphere

Nature ◽  
2005 ◽  
Vol 435 (7044) ◽  
pp. 919-921 ◽  
Author(s):  
Astrid Fossum ◽  
Mats Carlsson
2018 ◽  
Vol 611 ◽  
pp. A10 ◽  
Author(s):  
I. C. Santamaria ◽  
T. Van Doorsselaere

Aims. Null points are prominent magnetic field singularities in which the magnetic field strength strongly decreases in very small spatial scales. Around null points, predicted to be ubiquitous in the solar chromosphere and corona, the wave behavior changes considerably. Null points are also responsible for driving very energetic phenomena, and for contributing to chromospheric and coronal heating. In previous works we demonstrated that slow magneto-acoustic shock waves were generated in the chromosphere propagate through the null point, thereby producing a train of secondary shocks escaping along the field lines. A particular combination of the shock wave speeds generates waves at a frequency of 80 MHz. The present work aims to investigate this high frequency region around a coronal null point to give a plausible explanation to its generation at that particular frequency. Methods. We carried out a set of two-dimensional numerical simulations of wave propagation in the neighborhood of a null point located in the corona. We varied both the amplitude of the driver and the atmospheric properties to investigate the sensitivity of the high frequency waves to these parameters. Results. We demonstrate that the wave frequency is sensitive to the atmospheric parameters in the corona, but it is independent of the strength of the driver. Thus, the null point behaves as a resonant cavity generating waves at specific frequencies that depend on the background equilibrium model. Moreover, we conclude that the high frequency wave train generated at the null point is not necessarily a result of the interaction between the null point and a shock wave. This wave train can be also developed by the interaction between the null point and fast acoustic-like magneto-acoustic waves, that is, this interaction within the linear regime.


2007 ◽  
Vol 3 (S247) ◽  
pp. 312-315 ◽  
Author(s):  
Aleksandra Andic ◽  
M. Mathioudakis ◽  
F. P. Keenan ◽  
D. B. Jess ◽  
D. S. Bloomfield

AbstractHigh frequency acoustic waves have been suggested as a source of mechanical heating in the quiet solar chromosphere. To investigate this, we have observed intensity oscillations of several lines in the frequency interval 1.64-70mHz using data from the VTT Tenerife and the Dunn Solar Telescope at the National Solar Observatory. Our analysis of Fe i 543.45 nm, Fe i 543.29 nm and the G-band, indicate that the majority of oscillations are connected with the magnetic fields and do not provide sufficient mechanical flux for the heating of the chromosphere. This correlation is also observed in quiet Sun areas.


Sensors ◽  
2021 ◽  
Vol 21 (12) ◽  
pp. 4221
Author(s):  
Roshan Joseph ◽  
Hanfei Mei ◽  
Asaad Migot ◽  
Victor Giurgiutiu

Acoustic waves are widely used in structural health monitoring (SHM) for detecting fatigue cracking. The strain energy released when a fatigue crack advances has the effect of exciting acoustic waves, which travel through the structures and are picked up by the sensors. Piezoelectric wafer active sensors (PWAS) can effectively sense acoustic waves due to fatigue-crack growth. Conventional acoustic-wave passive SHM, which relies on counting the number of acoustic events, cannot precisely estimate the crack length. In the present research, a novel method for estimating the crack length was proposed based on the high-frequency resonances excited in the crack by the energy released when a crack advances. In this method, a PWAS sensor was used to sense the acoustic wave signal and predict the length of the crack that generated the acoustic event. First, FEM analysis was undertaken of acoustic waves generated due to a fatigue-crack growth event on an aluminum-2024 plate. The FEM analysis was used to predict the wave propagation pattern and the acoustic signal received by the PWAS mounted at a distance of 25 mm from the crack. The analysis was carried out for crack lengths of 4 and 8 mm. The presence of the crack produced scattering of the waves generated at the crack tip; this phenomenon was observable in the wave propagation pattern and in the acoustic signals recorded at the PWAS. A study of the signal frequency spectrum revealed peaks and valleys in the spectrum that changed in frequency and amplitude as the crack length was changed from 4 to 8 mm. The number of peaks and valleys was observed to increase as the crack length increased. We suggest this peak–valley pattern in the signal frequency spectrum can be used to determine the crack length from the acoustic signal alone. An experimental investigation was performed to record the acoustic signals in crack lengths of 4 and 8 mm, and the results were found to match well with the FEM predictions.


2005 ◽  
Vol 23 (1) ◽  
pp. 47-53 ◽  
Author(s):  
E. V. Mishin ◽  
W. J. Burke ◽  
T. Pedersen

Abstract. Observations of airglow at 630nm (red line) and 557.7nm (green line) during HF modification experiments at the High Frequency Active Auroral Research Program (HAARP) heating facility are analyzed. We propose a theoretical framework for understanding the generation of Langmuir and ion acoustic waves during magnetic zenith injections. We show that observations of HF-induced airglow in an underdense ionosphere as well as a decrease in the height of the emitting volume are consistent with this scenario.


2009 ◽  
Vol 92 (4) ◽  
pp. 49-55
Author(s):  
Tsutomu Sasaki ◽  
Yasutomo Tanaka ◽  
Tatsuya Omori ◽  
Ken-Ya Hashimoto ◽  
Masatsune Yamaguchi

Sign in / Sign up

Export Citation Format

Share Document