scholarly journals Chloride Inclusion and Hole Transport Material Doping to Improve Methyl Ammonium Lead Bromide Perovskite-Based High Open-Circuit Voltage Solar Cells

2014 ◽  
Vol 5 (3) ◽  
pp. 429-433 ◽  
Author(s):  
Eran Edri ◽  
Saar Kirmayer ◽  
Michael Kulbak ◽  
Gary Hodes ◽  
David Cahen
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Hole Transport ◽  
Lead Bromide

High Open-Circuit Voltage Solar Cells Based on Organic–Inorganic Lead Bromide Perovskite

2013 ◽  
Vol 4 (6) ◽  
pp. 897-902 ◽  
Author(s):  
Eran Edri ◽  
Saar Kirmayer ◽  
David Cahen ◽  
Gary Hodes
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Inorganic Lead ◽  
Lead Bromide

FAPbBr3 perovskite solar cells with VOC over 1.5 V by controlled crystal growth using a tetramethylenesulfoxide

2021 ◽  
Author(s):  
Youhei Numata ◽  
Naoyuki Shibayama ◽  
Tsutomu Miyasaka
Keyword(s):  
Solar Cells ◽  
Crystal Growth ◽  
Open Circuit Voltage ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Sequential Deposition ◽  
Lead Bromide

Perovskite solar cells (PSC) capable of open-circuit voltage (VOC) over 1.5 V was fabricated based on a formamidinium lead-bromide (FAPbBr3) perovskite absorber film prepared by sequential deposition procedure using dimethylsulfoxide...

Optical Simulation and Investigation of the Effect of Hysteresis on the Perovskite Solar Cells

NANO ◽  
2019 ◽  
Vol 14 (10) ◽  
pp. 1950127 ◽  
Author(s):  
Farhad Jahantigh ◽  
S. M. Bagher Ghorashi
Keyword(s):  
Grain Size ◽  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Perovskite solar cells have recently been considered to be an auspicious candidate for the advancement of future photovoltaic research. A power conversion efficiency (PCE) as high as 22% has been reported to be reached, which can be obtained through an inexpensive and high-throughput solution process. Modeling and simulation of these cells can provide deep insights into their fundamental mechanism of performance. In this paper, two different perovskite solar cells are designed by using COMSOL Multiphysics to optimize the thickness of each layer and the overall thickness of the cell. Electric potential, electron and hole concentrations, generation rate, open-circuit voltage, short-circuit current and the output power were calculated. Finally, PCEs of 20.7% and 26.1% were predicted. Afterwards, according to the simulation results, the role of the hole transport layer (HTL) was investigated and the optimum thickness of the perovskite was measured to be 200[Formula: see text]nm for both cells. Therefore, the spin coating settings are selected so that a coating with this thickness for cell 1 is deposited. In order to compare the performance of HTM layer, solar cells with a Spiro-OMeTAD HTM and without the HTM layer in their structure were fabricated. According to the obtained photovoltaic properties, the solar cell made with Spiro-OMeTAD has a more favorable open-circuit voltage ([Formula: see text]), short-circuit current density ([Formula: see text]), fill factor (FF) and PCE compared to the cell without the HTM layer. Also, hysteresis depends strongly on the perovskite grain size, because large average grain size will lead to an increase in the grain’s contact surface area and a decrease in the density of grain boundaries. Finally, according to the results, it was concluded that, in the presence of a hole transport layer, ion transfer was better and ion accumulation was less intense, and therefore, the hysteresis decreases.

Carbon nanotubes as an efficient hole collector for high voltage methylammonium lead bromide perovskite solar cells

Nanoscale ◽  
2016 ◽  
Vol 8 (12) ◽  
pp. 6352-6360 ◽  
Author(s):  
Zhen Li ◽  
Pablo P. Boix ◽  
Guichuan Xing ◽  
Kunwu Fu ◽  
Sneha A. Kulkarni ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Solar Cells ◽  
High Voltage ◽  
Open Circuit Voltage ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Lead Bromide

A high open circuit voltage close to 1.4 V is achieved when carbon nanotubes are used as a hole conductor in methyl ammonium lead bromide perovskite solar cells.

p-Doping of organic hole transport layers in p–i–n perovskite solar cells: correlating open-circuit voltage and photoluminescence quenching

2019 ◽  
Vol 7 (32) ◽  
pp. 18971-18979 ◽  
Author(s):  
Tian Du ◽  
Weidong Xu ◽  
Matyas Daboczi ◽  
Jinhyun Kim ◽  
Shengda Xu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Photoluminescence Quenching ◽  
Hole Transport Layers

Reduction in p-doping of the organic hole transport layer (HTL) leads to substantial improvements in PV performance in planar p–i–n perovskite solar cells.

Identifying and suppressing interfacial recombination to achieve high open-circuit voltage in perovskite solar cells

2017 ◽  
Vol 10 (5) ◽  
pp. 1207-1212 ◽  
Author(s):  
Juan-Pablo Correa-Baena ◽  
Wolfgang Tress ◽  
Konrad Domanski ◽  
Elham Halvani Anaraki ◽  
Silver-Hamill Turren-Cruz ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Interfacial Recombination

Dopants in the hole transport layer limit the open-circuit voltage of perovskite solar cells.

Sign in / Sign up

Export Citation Format

Share Document