Freeze-Drying: In Situ Observations Using Cryoenvironmental Scanning Electron Microscopy and Differential Scanning Calorimetry

1996 ◽  
Vol 85 (6) ◽  
pp. 631-637 ◽  
Author(s):  
Paul Meredith ◽  
Athene M. Donald ◽  
Robin S. Payne
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Freeze Drying ◽  
Scanning Calorimetry ◽  
In Situ Observations ◽  
Scanning Electron

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Effect of the dispersion of the chromophore on the optical performances of polarizers from polyethylene and 5”-thio- (3-butyl)nonyl-2,2’:5’,2”-terthiophene

e-Polymers ◽  
2002 ◽  
Vol 2 (1) ◽  
Author(s):  
Andrea Pucci ◽  
Letizia Moretto ◽  
Giacomo Ruggeri ◽  
Francesco Ciardelli
Keyword(s):  
Electron Microscopy ◽  
Molecular Weight ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Melting Point ◽  
Drawing Ratio ◽  
Scanning Calorimetry ◽  
Affine Deformation ◽  
Ultra High Molecular Weight ◽  
Scanning Electron

AbstractA new polyethylene-compatible terthiophene chromophore, 5”-thio-(3- butyl)nonyl-2,2’:5’,2”-terthiophene, with melting point lower than 0°C was prepared and used for linear polarizers based on ultra-high-molecular-weight polyethylene (UHMWPE). Differential scanning calorimetry and scanning electron microscopy indicate that the new chromophore is dispersed uniformly in films of UHMWPE obtained by casting from solution. The films show excellent dichroic properties (dichroic ratio 30) at rather low drawing ratio (≈ 20) . Moreover, qualitative agreement is observed with the Ward pseudo-affine deformation scheme.

Influence of Cementitious Capillary Crystalline Waterproofing Material on the Water Impermeability and Microstructure of Concrete

2019 ◽  
Vol 953 ◽  
pp. 209-214
Author(s):  
Yi Teng Zhang ◽  
Lian Zuo ◽  
Jin Chao Yang ◽  
Wei Xia Zhao ◽  
Xiang Xiong Zeng
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Cement Matrix ◽  
Hardened Cement ◽  
Hydration Products ◽  
Hardened Cement Paste ◽  
Scanning Calorimetry ◽  
Chinese Standard ◽  
Scanning Electron

The main objective of this study is to investigate the effect of cementitious capillary crystalline waterproofing (CCCW) material on the water impermeability and microstructure of concrete. The water impermeability of concrete covered with or without CCCW material was tested according to the Chinese standard GB 18445-2012. The results indicate that concretes coated with CCCW material showed much higher water impermeability than blank ones, and the ratio of water impermeability pressure between them reached 275. The samples obtained in various depths of hardened cement paste specimens with or without CCCW coating were analyzed through scanning electron microscopy (SEM) and thermogravimetry-differential scanning calorimetry (TG-DSC), to study the differences in microstructure and hydration products. The results present that after a 28-day standard curing, there were lots of ettringite crystals and CaCO3 formed in the paste in 1 cm from the coating, but the action depth of the CCCW coating could not reach 3 cm. The ettringite and CaCO3 is precipitated in the pore structure of cement matrix and filling the voids, which leads to the significant enhancement in water impermeability.

Study of an Energetic-oxidant Co-crystal: Preparation, Characterisation, and Crystallisation Mechanism

2017 ◽  
Vol 67 (5) ◽  
pp. 510 ◽  
Author(s):  
Han Gao ◽  
Wei Jiang ◽  
Jie Liu ◽  
Gazi Hao ◽  
Lei Xiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Diffraction Spectrum ◽  
Solvent Evaporation Method ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

<p>An energetic co-crystal consisting of the most promising military explosive 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and the most well-known oxidant applied in propellants ammonium perchlorate has been prepared with a simple solvent evaporation method. Scanning electron microscopy revealed that the morphology of co-crystal differs greatly from each component. The X-ray diffraction spectrum, FTIR, Raman spectra, and differential scanning calorimetry characterisation further prove the formation of the co-crystal. The result of determination of hygroscopic rate indicated the hygroscopicity was effectively reduced. At last, the crystallisation mechanism has been discussed.</p>

Hydriding Behaviour of Mg-C Nanocomposites

2003 ◽  
Vol 801 ◽  
Author(s):  
A. Bassetti ◽  
E. Bonetti ◽  
A. L. Fiorini ◽  
J. Grbovic ◽  
A. Montone ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Weight Ratio ◽  
Hydrogen Desorption ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Carbon Nanocomposites ◽  
X Ray ◽  
Scanning Electron

ABSTRACTMagnesium carbon nanocomposites for hydrogen storage have been synthesized by ball milling with different amount of benzene, acting as a lubricant. Their microstructure has been studied by X-ray diffraction and scanning electron microscopy, while the hydrogen desorption temperature has been tested by differential scanning calorimetry. Experimental results show that the microstructure after milling, the hydrogenation capabilities of the material and the reactivity with the air are related to the amount of additives. In particular the carbon to benzene ratio seems to play a major role. In fact, with an optimum value of carbon to benzene weight ratio of 1/6, the amount of carbon being 15 wt% of the milled mixture, a decomposition heat equal to 57% of pure MgH2 was measured, even after air manipulation of the sample.

scholarly journals Polyurethanes used in the endoprosthesis of joints

2010 ◽  
Vol 12 (3) ◽  
pp. 10-14 ◽  
Author(s):  
Agata Domańska ◽  
Anna Boczkowska ◽  
Marta Izydorzak ◽  
Zbigniew Jaegermann ◽  
Krzysztof Kurzydłowski
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Abrasive Wear ◽  
Biodegradable Polymer ◽  
Composite Ceramics ◽  
Ceramic Core ◽  
Scanning Calorimetry ◽  
Selection Of ◽  
Scanning Electron

Polyurethanes used in the endoprosthesis of joints The aim of the studies presented in this paper was the selection of the polyurethanes synthesized from different substrates in order to obtain i) ceramic - biodegradable polymer composite and ii) polyurethane resistant to abrasive wear. The polyurethanes were obtained from the crystalline prepolymers extended by water, because it may have a beneficial effect on the toxicity of the material. The properties of PUs were investigated using infrared spectroscopy, thermogravimetry, differential scanning calorimetry and scanning electron microscopy. In all the tested polyurethanes the peak from the reactive -NCO groups was not observed, which indicates that all the substrates are fully reacted. Such polyurethanes are characterized by interesting properties with the perspective use as components of ceramic-polymer joints endoprosthesis. The designed endoprosthesis should fulfill at least three functions: load bearing function (ceramic core), fastening and stabilizing endoprosthesis to the bone (composite ceramics - biodegradable polymer) and tribologic function allowing mating with parts of the prosthesis (polyurethane layer resistant to abrasive wear).

Sign in / Sign up

Export Citation Format

Share Document