Amaranthus cruentusFlour Edible Films: Influence of Stearic Acid Addition, Plasticizer Concentration, and Emulsion Stirring Speed on Water Vapor Permeability and Mechanical Properties

2006 ◽  
Vol 54 (18) ◽  
pp. 6645-6653 ◽  
Author(s):  
Eliane Colla ◽  
Paulo J. do Amaral Sobral ◽  
Florencia Cecília Menegalli
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Stearic Acid ◽  
Water Vapor Permeability ◽  
Edible Films ◽  
Vapor Permeability ◽  
Acid Addition ◽  
Plasticizer Concentration

Research on Preparation and Properties of Edible Composite Protein Films

2011 ◽  
Vol 87 ◽  
pp. 213-222 ◽  
Author(s):  
Gui Yun Chen ◽  
Qiao Lei
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Water Solubility ◽  
Water Vapor Permeability ◽  
Sodium Caseinate ◽  
Barrier Properties ◽  
Edible Films ◽  
Protein Isolate ◽  
Vapor Permeability ◽  
Protein Films

Edible films based on whey protein isolate and sodium caseinate were prepared by uniform design method. Glycerol has been incorporated into the edible films as a plasticizer. For all types of films, the influences of components and forming temperature on film properties, such as mechanical properties, water solubility, optical properties, gas and water vapor permeability were investigated. The results suggested that glycerol was the most important factor influencing all the properties of edible composite protein films. However, both increases of sodium caseinate concentration and glycerol content contributed to decrease the barrier properties of gas and water vapor. Among the films studied, group D (prepared with 5% whey protein isolate, 2% sodium caseinate, 50% glycerol at the temperature of 50 °C) showed moderate mechanical properties, optical properties, water solubility and maximum barrier properties of gas and water vapor, with tensile strength=5.85MPa, elongation=101.20%, transparency=91.4%, gas permeability rate=49.92cm3m-2d-10.1MPa-1and water vapor permeability of 0.128×10-11g m-1s-1Pa-1, 0.260×10-11g m-1s-1Pa-1, 0.513×10-11g m-1s-1Pa-1, 1.252×10-11g m-1s-1Pa-1at the RH gradient of 10-40%, 10-50%, 10-60%, 10-70%, respectively.

scholarly journals Effect of cellulose nanofibers concentration on mechanical, optical, and barrier properties of gelatin-based edible films

DYNA ◽  
2015 ◽  
Vol 82 (191) ◽  
pp. 219-226 ◽  
Author(s):  
Ricardo David Andrade Pizarro ◽  
Olivier Skurtys ◽  
Fernando Osorio-Lira
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Cellulose Nanofibers ◽  
Water Vapor Permeability ◽  
Barrier Properties ◽  
Edible Films ◽  
Mechanical Tests ◽  
Vapor Permeability ◽  
Glycerol Concentration ◽  
Gelatin Concentration

The effect of gelatin, glycerol, and cellulose nanofiber (CNFs) concentrations on the mechanical properties, water vapor permeability, and color parameters of films was evaluated. The results indicate that the color is only affected by the gelatin concentration. Mechanical tests indicated that with increasing concentration of gelatin and CNFs, there is an increase in tensile strength, whereas an increase in glycerol concentration causes an increase in elongation, making the films more flexible. An increased concentration of gelatin and glycerol makes the film more permeable to water vapor, while an increase in the concentration of CNFs reduces this property. Finally, the addition of CNFs to gelatin-based films improves their mechanical and barrier properties (water vapor) without affecting the appearance (color) of the films.

scholarly journals Characterization of Chickpea (Cicer arietinum L.) Flour Films: Effects of pH and Plasticizer Concentration

2019 ◽  
Vol 20 (5) ◽  
pp. 1246 ◽  
Author(s):  
Olga Díaz ◽  
Tania Ferreiro ◽  
José Rodríguez-Otero ◽  
Ángel Cobos
Keyword(s):  
Water Vapor ◽  
Radical Scavenging ◽  
Water Vapor Permeability ◽  
Edible Films ◽  
Vapor Permeability ◽  
Dry Matter Content ◽  
Glycerol Concentration ◽  
Chickpea Flour ◽  
Film Forming ◽  
Plasticizer Concentration

The use of flours as a material for biopolymer-based film preparation has gained interest due to the fact that they are a natural mixture of compatible macromolecules and due to their low cost. Chickpea flour shows a promising composition for the development of edible films. The aim of this study was to characterize and evaluate the properties of chickpea flour films as affected by pH (7 or 10) and plasticizer concentration (1% or 3% w/v) of film-forming solutions. Water vapor permeability, solubility, color, opacity, mechanical properties, thermal stability, structural changes by Fourier transform infrared analysis, and microstructure of the films were determined. Glycerol content and pH influenced chickpea flour film properties, microstructure and structural organization; interactions were also observed. The 1% glycerol films showed lower water vapor permeability, thickness, radical scavenging capacity, elongation at break and puncture deformation, and higher dry matter content, swelling, opacity, elastic modulus, and tensile and puncture strengths than 3% glycerol films. Film-forming solutions at pH 10 produced films with higher thickness and swelling, and were greener than those from solutions at neutral pH. The changes were more intense in 1% glycerol films. Glycerol concentration and pH could be combined in order to obtain chickpea flour films with different properties according to different food packaging requirements.

Sign in / Sign up

Export Citation Format

Share Document