Optimization of Parameters for Adsorption of Methylene Blue on a Low-Cost Activated Carbon

2010 ◽  
Vol 55 (1) ◽  
pp. 435-439 ◽  
Author(s):  
Yogesh C. Sharma ◽  
Uma
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Low Cost ◽  
Optimization Of Parameters

scholarly journals Optimisation of durian peel based activated carbon preparation conditions for dye removal

2013 ◽  
Vol 16 (1) ◽  
pp. 22-31
Author(s):  
Phung Thi Kim Le ◽  
Kien Anh Le
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Dye Removal ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Impregnation Ratio ◽  
Carbon Production ◽  
Removal Capacity

Agricultural wastes are considered to be a very important feedstock for activated carbon production as they are renewable sources and low cost materials. This study present the optimize conditions for preparation of durian peel activated carbon (DPAC) for removal of methylene blue (MB) from synthetic effluents. The effects of carbonization temperature (from 673K to 923K) and impregnation ratio (from 0.2 to 1.0) with potassium hydroxide KOH on the yield, surface area and the dye adsorbed capacity of the activated carbons were investigated. The dye removal capacity was evaluated with methylene blue. In comparison with the commercial grade carbons, the activated carbons from durian peel showed considerably higher surface area especially in the suitable temperate and impregnation ratio of activated carbon production. Methylene blue removal capacity appeared to be comparable to commercial products; it shows the potential of durian peel as a biomass source to produce adsorbents for waste water treatment and other application. Optimize condition for preparation of DPAC determined by using response surface methodology was at temperature 760 K and IR 1.0 which resulted the yield (51%), surface area (786 m2/g), and MB removal (172 mg/g).

scholarly journals Synthesis of activated carbon from biowaste of fir bark for methylene blue removal

2019 ◽  
Vol 6 (9) ◽  
pp. 190523 ◽  
Author(s):  
Lu Luo ◽  
Xi Wu ◽  
Zeliang Li ◽  
Yalan Zhou ◽  
Tingting Chen ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Nonlinear Models ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Raw Material ◽  
Maximum Adsorption Capacity ◽  
Koh Activation ◽  
Mb Adsorption

Activated carbon (AC) was successfully prepared from low-cost forestry fir bark (FB) waste using KOH activation method. Morphology and texture properties of ACFB were studied by scanning and high-resolution transmission electron microscopies (SEM and HRTEM), respectively. The resulting fir bark-based activated carbon (ACFB) demonstrated high surface area (1552 m 2 g −1 ) and pore volume (0.84 cm 3 g −1 ), both of which reflect excellent potential adsorption properties of ACFB towards methylene blue (MB). The effect of various factors, such as pH, initial concentration, adsorbent content as well as adsorption duration, was studied individually. Adsorption isotherms of MB were fitted using all three nonlinear models (Freundlich, Langmuir and Tempkin). The best fitting of MB adsorption results was obtained using Freundlich and Temkin. Experimental results showed that kinetics of MB adsorption by our ACFB adsorbent followed pseudo-second-order model. The maximum adsorption capacity obtained was 330 mg g −1 , which indicated that FB is an excellent raw material for low-cost production of AC suitable for cationic dye removal.

scholarly journals Removal of Methylene Blue from Waste Water Using Activated Carbon Prepared from Rice Husk

2012 ◽  
Vol 60 (2) ◽  
pp. 185-189 ◽  
Author(s):  
Mohammad Arifur Rahman ◽  
S. M. Ruhul Amin ◽  
A. M. Shafiqul Alam
Keyword(s):  
Waste Water ◽  
Methylene Blue ◽  
Activated Carbon ◽  
Aqueous Solutions ◽  
Rice Husk ◽  
Flow Rate ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Blue Dye

The possible utilization of rice husk activated carbon as an adsorbent for the removal of methylene blue dye from aqueous solutions has been investigated. In this study, activated carbons, prepared from low-cost rice husk by sulfuric acid and zinc chloride activation, were used as the adsorbent for the removal of methylene blue, a basic dye, from aqueous solutions. Effects of various experimental parameters, such as adsorbent dosage and particle size, initial dye concentration, pH and flow rate were investigated in column process. The maximum uptakes of methylene blue by activated rice husk carbon at optimized conditions (particle sizes: 140 ?m; Flow rate: 1.4 mL/min; pH: 10.0; initial volume of methylene blue: 50 mL and initial concentration of methylene blue: 4.0 mg/L etc.) were found to 97.15%. The results indicate that activated carbon of rice husk could be employed as low-cost alternatives to commercial activated carbon in waste water treatment for the removal of basic dyes. This low cost and effective removal method may provide a promising solution for the removal of crystal violet dye from wastewater.DOI: http://dx.doi.org/10.3329/dujs.v60i2.11491 Dhaka Univ. J. Sci. 60(2): 185-189, 2012 (July)

Removal of Methylene Blue by Adsorption Process - A Comparative Study

2011 ◽  
Vol 699 ◽  
pp. 245-264 ◽  
Author(s):  
A. Xavier ◽  
J. Gandhi Rajan ◽  
D. Usha ◽  
R Sathya
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Blue Dye ◽  
Molecular Formula

Methylene blue is a heterocyclic aromatic chemical compound with the molecular formula C16H18N3SCl. It has used in the biology and chemistry field. At room temperature, it appears as a solid, odourless dark green powder that yields blue solution when dissolved in water. As a part of removal of methylene blue dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage of Methylene blue adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbents. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data the modeled with Freundlich and Langmuir isotherms. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and MB is particular. These results are reported highly efficient and effective and low cost adsorbent for the MB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM photos.

scholarly journals Methylene blue removal using a low-cost activated carbon adsorbent from tobacco stems: kinetic and equilibrium studies

2017 ◽  
Vol 75 (10) ◽  
pp. 2390-2402 ◽  
Author(s):  
Bellington Mudyawabikwa ◽  
Henry H. Mungondori ◽  
Lilian Tichagwa ◽  
David M. Katwire
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Radiation Power ◽  
Low Cost ◽  
Carbon Adsorbent ◽  
Point Of Zero Charge ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Equilibrium Studies ◽  
Mb Adsorption

The aim of this study was to prepare activated carbon from tobacco stalks using microwave heating. The prepared activated carbon was applied as an adsorbent in methylene blue (MB) removal from water. The optimum conditions for activated carbon preparation were a radiation power of 280 W for a period of 6 minutes after the impregnation of the precursor material with 30% ZnCl2 for 24 hours. The activated carbon yield and iodine number were 49.43% and 1,264.51 mg/g respectively. The activated carbon also had a point of zero charge of 5.81 with an adsorption capacity of 123.45 mg/g for MB. The optimum conditions for MB adsorption were a pH of 6.5 with an adsorbent dosage of 0.2 g/50 mL at 25 °C. The MB adsorption kinetics followed the pseudo second order kinetic model with the intra-particle diffusion model suggesting a two-step adsorption mechanism. The adsorption data also fitted well within the Langmuir adsorption isotherm model. Tobacco stalks can successfully be turned into an economically important product.

scholarly journals Methylene Blue removal from aqueous solutions by activated carbon prepared from N. microphyllum (AC-NM): RSM analysis, isotherms and kinetic studies

2017 ◽  
Vol 19 (4) ◽  
pp. 697-705 ◽  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Low Cost ◽  
Kinetic Studies ◽  
P Value ◽  
Water And Wastewater Treatment ◽  
Freundlich Model ◽  
Initial Concentration ◽  
Layer Adsorption ◽  
Water And Wastewater

This study was conducted to remove Methylene Blue (MB) from aqueous solution using activated carbon prepared from N. microphyllum (AC-NM) as a new, cheap, and non-toxic. Design of experiments based on Response Surface Methodology (RSM) conducted to investigate the effect of variables namely; initial dye concentration, pH, contact time and absorbent dosage. An empirical model was developed applying ANOVA analysis. The interaction effects of all factors and their optimization have been carried out using RSM. Dye removal efficiency increased to more than 90% with increasing pH and initial concentration of dye from 3 to 11 and 10 to 210 mg/L, respectively under 1.1 to 1.4 g/L of absorbent dosage. Among factors, initial concentration of MB known as an important factor with P- value <0.0001. The experimental data are fitted with Freundlich model based on multi layer adsorption states (R2=0.99). The adsorption kinetics well described by second order model with R2 = 0.98. This novel absorbent has different advantages such as low cost, high ability to absorb pollutants and easily available that can be suggested for water and wastewater treatment.

Characterization of the Corallina Elongata Alga and Study of its Biosorption Properties for Methylene Blue

2019 ◽  
Vol 41 (1) ◽  
pp. 62-62
Author(s):  
Farida Bouremmad Farida Bouremmad ◽  
Abdennour Bouchair Abdennour Bouchair ◽  
Sorour Semsari Parapari Sorour Semsari Parapari ◽  
Shalima Shawuti and Mehmet Ali Gulgun Shalima Shawuti and Mehmet Ali Gulgun
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Mediterranean Coast ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Aquatic Biomass ◽  
Equilibrium Data

Biosorbents can be an alternative to activated carbon. They are derived from agricultural by-products or aquatic biomass. They are low cost and they may have comparable performances to those of activated carbon. The present study focuses on the characterization of the Corallina Elongata (CE) alga and its adsorption performance for Methylene Blue (MB), this alga is found in abundance at the Mediterranean coast of the city of Jijel in eastern Algeria. The dried alga was characterized using various characterization techniques such as DTA, TG, FTIR, XRD, SEM and EDX, which showed that the material consists essentially of a calcite containing magnesium. Batch adsorption studies were carried out and the effect of experimental parameters Such as pH, initial dye concentration, temperature, adsorbent dose and contact time, on the adsorption of MB was studied. The kinetic experimental data were found to conform to the pseudo-second-order model with good correlation and equilibrium data were best fitted to The Langmuir model, with a maximum adsorption capacity of 34.4 mg/g. The adsorption isotherms at various temperatures allowed the determination of certain thermodynamic parameters (ΔG, ΔH and ΔS). Finally, the adsorption results showed a good affinity between CE and MB with a high adsorption capacity.

Preparation and Characterization of Textile Sludge-Based Activated Carbon for Dyes Removal

2016 ◽  
Vol 818 ◽  
pp. 250-253
Author(s):  
Nurul Atiqah Najlaa Yac’cob ◽  
Norzita Ngadi ◽  
Roshanida Abd Rahman
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
Reactive Black 5 ◽  
Adsorbent Dosage ◽  
Percentage Removal ◽  
Textile Sludge ◽  
Dyes Removal

An activated carbon derived from textile sludge was synthesized as an initiative of low cost adsorbent for removal of dyes. The surface area of this activated carbon was determined by Brunauer, Emmett and Teller (BET). From the BET results, it shows a high increment in the BET multi point area for textile sludge-activated carbon as compared to the textile sludge, which is 623.9557 m2/g and 58.9806 m2/g, respectively. The effects of initial adsorbent dosage were studied in the removal of Reactive Black 5 (RB5) and Methylene Blue (MB) dyes. RB5 and MB dyes solutions were used to represent anionic and cationic dyes respectively. It was concluded that the adsorbent dosage was proportional to the dyes removal for both RB5 and MB with percentage removal up to 99%.

Sign in / Sign up

Export Citation Format

Share Document