Three-Dimensional Paper Microfluidic Devices Assembled Using the Principles of Origami

2011 ◽  
Vol 133 (44) ◽  
pp. 17564-17566 ◽  
Author(s):  
Hong Liu ◽  
Richard M. Crooks
Keyword(s):  
Three Dimensional ◽  
Microfluidic Devices ◽  
Paper Microfluidic

scholarly journals A Numerical Study of Sub-Millisecond Integrated Mix-and-Inject Microfluidic Devices for Sample Delivery at Synchrotron and XFELs

2021 ◽  
Vol 11 (8) ◽  
pp. 3404
Author(s):  
Majid Hejazian ◽  
Eugeniu Balaur ◽  
Brian Abbey
Keyword(s):  
Molecular Dynamics ◽  
Flow Rate ◽  
Numerical Study ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Liquid Jets ◽  
Mixing Efficiency ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
Time Required

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

scholarly journals Automation of Three-Dimensional Cell Culture in Arrayed Microfluidic Devices

2011 ◽  
Vol 16 (3) ◽  
pp. 171-185 ◽  
Author(s):  
Sara I. Montanez-Sauri ◽  
Kyung Eun Sung ◽  
John P. Puccinelli ◽  
Carolyn Pehlke ◽  
David J. Beebe
Keyword(s):  
Cell Culture ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Dimensional Cell

scholarly journals Rapid and Inexpensive Fabrication of Multi-Depth Microfluidic Device using High-Resolution LCD Stereolithographic 3D Printing

2019 ◽  
Vol 3 (1) ◽  
pp. 26 ◽  
Author(s):  
Mohamed Mohamed ◽  
Hitendra Kumar ◽  
Zongjie Wang ◽  
Nicholas Martin ◽  
Barry Mills ◽  
...  
Keyword(s):  
High Resolution ◽  
3D Printing ◽  
Soft Lithography ◽  
Liquid Crystal Display ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Single Step ◽  
Droplet Generator ◽  
Rapid Fabrication ◽  
Printing System

With the dramatic increment of complexity, more microfluidic devices require 3D structures, such as multi-depth and -layer channels. The traditional multi-step photolithography is time-consuming and labor-intensive and also requires precise alignment during the fabrication of microfluidic devices. Here, we present an inexpensive, single-step, and rapid fabrication method for multi-depth microfluidic devices using a high-resolution liquid crystal display (LCD) stereolithographic (SLA) three-dimensional (3D) printing system. With the pixel size down to 47.25 μm, the feature resolutions in the horizontal and vertical directions are 150 μm and 50 μm, respectively. The multi-depth molds were successfully printed at the same time and the multi-depth features were transferred properly to the polydimethylsiloxane (PDMS) having multi-depth channels via soft lithography. A flow-focusing droplet generator with a multi-depth channel was fabricated using the presented 3D printing method. Experimental results show that the multi-depth channel could manipulate the morphology and size of droplets, which is desired for many engineering applications. Taken together, LCD SLA 3D printing is an excellent alternative method to the multi-step photolithography for the fabrication of multi-depth microfluidic devices. Taking the advantages of its controllability, cost-effectiveness, and acceptable resolution, LCD SLA 3D printing can have a great potential to fabricate 3D microfluidic devices.

scholarly journals Using printer ink color to control the behavior of paper microfluidics

Lab on a Chip ◽  
2019 ◽  
Vol 19 (11) ◽  
pp. 2000-2008 ◽  
Author(s):  
Joshua Potter ◽  
Philip Brisk ◽  
William H. Grover
Keyword(s):  
Microfluidic Devices ◽  
Paper Microfluidics ◽  
Paper Microfluidic

Different colors of wax inks behave differently in paper microfluidic devices, enabling the development of new color-based paper microfluidic components.

scholarly journals Effect of Process Parameters and Material Properties on Laser Micromachining of Microchannels

Micromachines ◽  
2019 ◽  
Vol 10 (2) ◽  
pp. 123 ◽  
Author(s):  
Matthew Benton ◽  
Mohammad Hossan ◽  
Prashanth Konari ◽  
Sanjeewa Gamagedara
Keyword(s):  
Process Parameters ◽  
Laser System ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Scanning Speed ◽  
Transient Heat Conduction ◽  
Laser Micromachining ◽  
Rapid Phase ◽  
Widespread Application ◽  
Optimization Of Process Parameters

Laser micromachining has emerged as a promising technique for mass production of microfluidic devices. However, control and optimization of process parameters, and design of substrate materials are still ongoing challenges for the widespread application of laser micromachining. This article reports a systematic study on the effect of laser system parameters and thermo-physical properties of substrate materials on laser micromachining. Three dimensional transient heat conduction equation with a Gaussian laser heat source was solved using finite element based Multiphysics software COMSOL 5.2a. Large heat convection coefficients were used to consider the rapid phase transition of the material during the laser treatment. The depth of the laser cut was measured by removing material at a pre-set temperature. The grid independent analysis was performed for ensuring the accuracy of the model. The results show that laser power and scanning speed have a strong effect on the channel depth, while the level of focus of the laser beam contributes in determining both the depth and width of the channel. Higher thermal conductivity results deeper in cuts, in contrast the higher specific heat produces shallower channels for a given condition. These findings can help in designing and optimizing process parameters for laser micromachining of microfluidic devices.

Force modeling to develop a novel method for fabrication of hollow channels inside a gel structure

2019 ◽  
Vol 234 (2) ◽  
pp. 223-231 ◽  
Author(s):  
Ranjit Barua ◽  
Himanshu Giria ◽  
Sudipto Datta ◽  
Amit Roy Chowdhury ◽  
Pallab Datta
Keyword(s):  
Viscoelastic Material ◽  
Biomedical Engineering ◽  
Viscoelastic Properties ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Robotic Arm ◽  
Complex Geometries ◽  
Gel Structure ◽  
Force Modeling ◽  
Novel Method

Fabrication of hollow channels with user-defined dimensions and patterns inside viscoelastic, gel-type materials is required for several applications, especially in biomedical engineering domain. These include objectives of obtaining vascularized tissues and enclosed or subsurface microfluidic devices. However, presently there is no suitable manufacturing technology that can create such channels and networks in a gel structure. The advent of three-dimensional bioprinting has opened new possibilities for fabricating structures with complex geometries. However, application of this technique to fabricate internal hollow channels in viscoelastic material has not been yet explored to a great extent. In this article, we present the theoretical modeling/background of a proposed manufacturing paradigm through which hollow channels can be conveniently fabricated inside a gel structure. We propose that a tip connected to a robotic arm can be moved in X-, Y-, and Z-axis as per the desired design. The tip can be moved by a magnet or mechanical force. If the tip is further trailed with porous tube and moved inside the viscoelastic material, corresponding internal channels can be fabricated. To achieve this, however, force modeling to understand the forces that will be required to move the tip inside viscoelastic material should be known and understood. Therefore, in our first attempt, we developed the computational force modeling of the tip movement inside gels with different viscoelastic properties to create the channels.

scholarly journals 3D Printed Microfluidics

2020 ◽  
Vol 13 (1) ◽  
pp. 45-65 ◽  
Author(s):  
Anna V. Nielsen ◽  
Michael J. Beauchamp ◽  
Gregory P. Nordin ◽  
Adam T. Woolley
Keyword(s):  
3D Printing ◽  
Early Stage ◽  
Three Dimensional ◽  
Microfluidic Devices ◽  
Fabrication Method ◽  
Size Scale ◽  
Additional Work ◽  
Fluidic Devices ◽  
3D Printed ◽  
Microfabrication Techniques

Traditional microfabrication techniques suffer from several disadvantages, including the inability to create truly three-dimensional (3D) architectures, expensive and time-consuming processes when changing device designs, and difficulty in transitioning from prototyping fabrication to bulk manufacturing. 3D printing is an emerging technique that could overcome these disadvantages. While most 3D printed fluidic devices and features to date have been on the millifluidic size scale, some truly microfluidic devices have been shown. Currently, stereolithography is the most promising approach for routine creation of microfluidic structures, but several approaches under development also have potential. Microfluidic 3D printing is still in an early stage, similar to where polydimethylsiloxane was two decades ago. With additional work to advance printer hardware and software control, expand and improve resin and printing material selections, and realize additional applications for 3D printed devices, we foresee 3D printing becoming the dominant microfluidic fabrication method.

Sign in / Sign up

Export Citation Format

Share Document