The Surface and Interfacial Tension of Mercury by the Sessile Drop and Drop Weight Methods

1934 ◽  
Vol 56 (12) ◽  
pp. 2564-2568 ◽  
Author(s):  
H. Brown
Keyword(s):  
Interfacial Tension ◽  
Sessile Drop ◽  
Drop Weight

scholarly journals Interfacial Behaviour in Ferroalloys: The Influence of Sulfur in FeMn and SiMn Systems

2021 ◽  
Author(s):  
Sergey Bublik ◽  
Sarina Bao ◽  
Merete Tangstad ◽  
Kristian Etienne Einarsrud
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Sessile Drop ◽  
Interfacial Properties ◽  
Apparent Contact Angle ◽  
Holding Time ◽  
Transfer Rates ◽  
Experimental Parameters ◽  
Interfacial Behaviour ◽  
Modelling Approach

AbstractThe present study has investigated the influence of sulfur content in synthetic FeMn and SiMn from 0 to 1.00 wt pct on interfacial properties between these ferroalloys and slags. The effect of experimental parameters such as temperature and holding time was evaluated. Interfacial interaction between ferroalloys and slags was characterized by interfacial tension and apparent contact angle between metal and slag, measured based on the Young–Laplace equation and an inverse modelling approach developed in OpenFOAM. The results show that sulfur has a significant influence on both interfacial tension and apparent contact angle, decreasing both values and promoting the formation of a metal-slag mixture. Despite the fact that sulfur was added only to the ferroalloys, most of sulfur is distributed into slag after reactions with the metal phase. Increasing the maximum experimental temperature in the sessile drop furnace also resulted in a decrease of both interfacial properties, resulting in higher mass transfer rates and intensive reactions between metal and slag. The effect of holding time demonstrated that after reaching equilibrium in FeMn-slag and SiMn-slag systems (both with and without sulfur), interfacial tension and apparent contact angle remain constant.

scholarly journals Carbon dioxide adsorption and interaction with formation fluids of Jordanian unconventional reservoirs

2021 ◽  
Author(s):  
H. Samara ◽  
T. V. Ostrowski ◽  
F. Ayad Abdulkareem ◽  
E. Padmanabhan ◽  
P. Jaeger
Keyword(s):  
Carbon Dioxide ◽  
Contact Angle ◽  
Interfacial Tension ◽  
Oil Recovery ◽  
Gas Adsorption ◽  
Sessile Drop ◽  
Global Climate ◽  
Gravimetric Method ◽  
Rock Surface ◽  
Operating Pressure

AbstractShales are mostly unexploited energy resources. However, the extraction and production of their hydrocarbons require innovative methods. Applications involving carbon dioxide in shales could combine its potential use in oil recovery with its storage in view of its impact on global climate. The success of these approaches highly depends on various mechanisms taking place in the rock pores simultaneously. In this work, properties governing these mechanisms are presented at technically relevant conditions. The pendant and sessile drop methods are utilized to measure interfacial tension and wettability, respectively. The gravimetric method is used to quantify CO2 adsorption capacity of shale and gas adsorption kinetics is evaluated to determine diffusion coefficients. It is found that interfacial properties are strongly affected by the operating pressure. The oil-CO2 interfacial tension shows a decrease from approx. 21 mN/m at 0.1 MPa to around 3 mN/m at 20 MPa. A similar trend is observed in brine-CO2 systems. The diffusion coefficient is observed to slightly increase with pressure at supercritical conditions. Finally, the contact angle is found to be directly related to the gas adsorption at the rock surface: Up to 3.8 wt% of CO2 is adsorbed on the shale surface at 20 MPa and 60 °C where a maximum in contact angle is also found. To the best of the author’s knowledge, the affinity of calcite-rich surfaces toward CO2 adsorption is linked experimentally to the wetting behavior for the first time. The results are discussed in terms of CO2 storage scenarios occurring optimally at 20 MPa.

scholarly journals Effect of Direct Current on Solid-Liquid Interfacial Tension and Wetting Behavior of Ga–In–Sn Alloy Melt on Cu Substrate

2018 ◽  
Vol 2018 ◽  
pp. 1-7
Author(s):  
Limin Zhang ◽  
Ning Li ◽  
Hui Xing ◽  
Rong Zhang ◽  
Kaikai Song
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Direct Current ◽  
Sessile Drop ◽  
Contact Angles ◽  
Current Intensity ◽  
Solute Diffusion ◽  
Wetting Behavior ◽  
Cu Substrate ◽  
Solid Liquid

The effect of direct current (DC) on the wetting behavior of Cu substrate by liquid Ga–25In–13Sn alloy at room temperature is investigated using a sessile drop method. It is found that there is a critical value for current intensity, below which the decrease of contact angle with increasing current intensity is approximately linear and above which contact angle tends to a stable value from drop shape. Current polarity is a negligible factor in the observed trend. Additionally, the observed change in contact angles is translated into the corresponding change in solid-liquid interfacial tension using the equation of state for liquid interfacial tensions. The solid-liquid interfacial tension decreases under DC. DC-induced promotion of solute diffusion coefficient is likely to play an important role in determining the wettability and solid-liquid interfacial tension under DC.

Sign in / Sign up

Export Citation Format

Share Document