Antimony Pentafluoride: Density Melting Point and Vapor Pressure

1957 ◽  
Vol 61 (11) ◽  
pp. 1574-1575 ◽  
Author(s):  
Charles J. Hoffman ◽  
William L. Jolly
Keyword(s):  
Melting Point ◽  
Vapor Pressure ◽  
Antimony Pentafluoride

The density, viscosity, vapor pressure, melting point and flash point of a liquid propellant: 1-(2-azidoethyl) pyrrolidine

2016 ◽  
Vol 429 ◽  
pp. 113-118
Author(s):  
Jing Yang ◽  
Aijun Gong ◽  
Yayu Li ◽  
Zhaoyang Liu ◽  
Tao Fang ◽  
...  
Keyword(s):  
Melting Point ◽  
Vapor Pressure ◽  
Flash Point ◽  
Liquid Propellant ◽  
Pressure Melting

Vapor pressure studies of the hydrogen fluoride-antimony pentafluoride system

1991 ◽  
Vol 51 (2) ◽  
pp. 165-170
Author(s):  
Kent D. Abney ◽  
Gail R. Ball ◽  
P.Gary Eller
Keyword(s):  
Vapor Pressure ◽  
Hydrogen Fluoride ◽  
Antimony Pentafluoride

Phase Behavior and Its Effects on Reactions in Liquid and Supercritical Carbon Dioxide

2004 ◽  
Author(s):  
Lynnette A. Blanchard ◽  
Gang Xu
Keyword(s):  
Carbon Dioxide ◽  
Melting Point ◽  
Vapor Pressure ◽  
Phase Behavior ◽  
Critical Point ◽  
Pressure Curve ◽  
Light Component ◽  
Vapor Pressure Curve ◽  
Solid Liquid ◽  
Liquid Vapor

Carbon dioxide, either as an expanded liquid or as a supercritical fluid, may be a viable replacement for a variety of conventional organic solvents in reaction systems. Numerous studies have shown that many reactions can be conducted in liquid or supercritical CO2 (sc CO2) and, in some cases, rates and selectivities can be achieved that are greater than those possible in normal liquid- or gas-phase reactions (other chapters in this book; Noyori, 1999; Savage et al., 1995). Nonetheless, commercial exploitation of this technology has been limited. One factor that contributes to this reluctance is the extremely complex phase behavior that can be encountered with high-pressure multicomponent systems. Even for simple binary systems, one can observe multiple fluid phases, as shown in Figure 1.1. The figure shows the pressure–temperature (PT) projection of the phase diagram of a binary system, where the vapor pressure curve of the light component (e.g., CO2) is the solid line shown at temperatures below TB. It is terminated by its critical point, which is shown as a solid circle. The sublimation curve, melting curve, and vapor pressure curve of the pure component 2 (say, a reactant that is a solid at ambient conditions) are the solid lines shown at higher temperatures on the right side of the diagram; that is, the triple point of this compound is above TE. The solid might experience a significant melting point depression when exposed to CO2 pressure [the dashed–dotted solid/liquid/vapor (SLV) line, which terminates in an upper critical end point (UCEP)]. For instance, naphthalene melts at 60.1 °C under CO2 pressure (i.e., one might observe a three-phase solid/liquid/vapor system), even though the normal melting point is 80.5 °C (McHugh and Yogan, 1984). To complicate things even further, there will be a region close to the critical point of pure CO2 where one will observe three phases as well, as indicated by the dashed–dotted SLV line that terminates at the lower critical end point (LCEP). The dotted line connecting the critical point of the light component and the LCEP is a vapor/liquid critical point locus.

Experimental Investigation to the Properties of Eutectic Salts by NaCl-KCl-ZnCl2 for Application as High Temperature Heat Transfer Fluids

2014 ◽  
Author(s):  
Kai Wang ◽  
Edgar Molina ◽  
Ghazal Dehghani ◽  
Ben Xu ◽  
Peiwen Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Melting Point ◽  
Vapor Pressure ◽  
Mole Fraction ◽  
Heat Transfer Fluid ◽  
Test Facility ◽  
Vapor Pressures ◽  
Heat Transfer Fluids ◽  
Temperature Heat

A group of eutectic ternary halide salts were surveyed and studied for the objective of developing a high temperature heat transfer fluid with a freezing point below 250°C and a low vapor pressure, below 1.0 atm, at temperatures up to 800°C. The studied salts include: 1) NaCl-KCl-ZnCl2 with a mole fractions of 18.6%-21.9%-59.5% and a melting point of tm=213°C; 2) NaCl-KCl-ZnCl2 with a mole fraction of 13.4%-33.7%-52.9% and a melting point of tm=204°C; and 3) NaCl-KCl-ZnCl2 with mole fraction of 13.8%-41.9%-44.3% and a melting point of tm=229 °C. Vapor pressures of these salts at different temperatures were experimentally obtained using an in-house developed test facility. The results show that vapor pressures of all the three eutectic molten salts are below 1.0 atm at a temperature of 800 °C. The salt of ZnCl2-KCl-NaCl in mole faction of 44.3%-41.9%-13.8% has lowest vapor pressure which is only about 1.0 atm even at a temperature of 900 °C. Viscosities of these salts were measured in the temperature range from after melting to 850°C. At low temperatures near their melting points of the salts, the viscosities are about 16 × 10−3Pa s, while at high temperatures above 700°C the viscosities are around 4 × 10−3Pa s, which is satisfactorily low to serve as heat transfer fluid for circulation in a CSP system. Both the vapor pressure and the viscosities of the studied three eutectic salts demonstrated satisfaction to serve as high temperature heat transfer fluids. Other thermal and transport properties of these salts are expected to be reported in the future for screening out a satisfactory high temperature heat transfer fluid.

The Vapor Pressure and Melting Point of Graphite

1948 ◽  
Vol 16 (12) ◽  
pp. 1165-1166 ◽  
Author(s):  
Leo Brewer
Keyword(s):  
Melting Point ◽  
Vapor Pressure

Study for Radionuclide Transfer Ratio of Aerosols Generated During Heat Cutting

2007 ◽  
Author(s):  
Yukihiro Iguchi ◽  
Tsutomu Baba ◽  
Hiroto Kawakami ◽  
Takashi Kitahara ◽  
Atsushi Watanabe ◽  
...  
Keyword(s):  
Melting Point ◽  
Vapor Pressure ◽  
Test Sample ◽  
Inert Gas ◽  
Metallic Elements ◽  
High Vapor Pressure ◽  
Transfer Ratio ◽  
Air Atmosphere ◽  
Arc Melting ◽  
High Vapor

The metallic elements with a low melting point and high vapor pressure seemed to transfer in aerosols selectively at dismantling reactor internals using heat cutting. Therefore, the arc melting tests of neutron irradiated zirconium alloy were conducted to investigate the radionuclide transfer behavior of aerosols generated during the heat cutting of activated metals. The arc melting test was conducted using a tungsten inert gas welding machine in an inert gas or air atmosphere. The radioactive aerosols were collected by filter and charcoal filter. The test sample was obtained from Zry-2 fuel cladding irradiated in a Japanese boiling water reactor for five fuel cycles. The activity analysis, chemical composition measurement and scanning electron microscope observation of aerosols were carried out. Some radionuclides were enriched in the aerosols generated in an inert gas atmosphere and the radionuclide transfer ratio did not change remarkably by the presence of air. The transfer ratio of Sb-125 was almost the same as that of Co-60. It was expected that Sb-125 was enriched from other elements since Sb is an element with a low melting point and high vapor pressure compared with the base metal (Zr). In the viewpoint of the environmental impact assessment, it became clear that the influence if Sb-125 is comparable to Co-60. The transfer ratio of Mn-54 was one order higher compared with other radionuclides. The results were discussed on the basis of thermal properties and oxide formation energy of the metallic elements.

scholarly journals Synthesis of New Energetic Materials and Ionic Liquids Derived from Metronidazole

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Miguel A. Romero
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Ionic Liquids ◽  
Melting Point ◽  
Vapor Pressure ◽  
Energetic Materials ◽  
Antineoplastic Agents ◽  
Enzyme Inhibitors ◽  
Scanning Calorimetry ◽  
Energetic Ionic Liquids

Simple and efficient synthetic procedures were established for the preparation of new energetic covalent compounds, salts, and protonated ionic liquids based on the readily available antimicrobial agent metronidazole. Some of these materials exhibit the desirable properties of energetic materials and energetic ionic liquids, such as low vapor pressure, low melting point, good chemical and thermal stability, and high energetic content. For each of the relevant compounds prepared, thermal stability was determined by differential scanning calorimetry. Some of these compounds may be considered promising precursors of pharmaceuticals such as antimicrobial, antiparasitic, antifungal, antineoplastic agents, or enzyme inhibitors.

Sign in / Sign up

Export Citation Format

Share Document